Your search resulted in 3096 documents. Displaying 25 entries per page.
Modern Instrumental Methods to Investigate the Mechanism of Biological Decay in Wood Plastic Composites
2014 - IRG/WP 14-40674
Various instrumental techniques were used to study the fungal decay process in wood plastic composite (WPC) boards. Commercial boards exposed near Hilo, Hawaii (HI) for eight years in both sun and shadow locations were inspected and tested periodically. After eight years of exposure, both boards were evaluated using magnetic resonance imaging (MRI), while a selected area of the board exposed in sh...
G Sun, R Ibach, M Gnatowski, J Glaeser, M Leung, J Haight
Applicability of wood durability testing methods to bio-based building materials
2015 - IRG/WP 15-20561
It is well known that organic materials may be susceptible to attack from a range of fungal organisms and any bio-based material used in locations where there is the possibility of microbiological activity must be expected to be able to withstand or prevent such attack. There are a wide range of test methods and standards in place to test susceptibility although most of these test individual compo...
S F Curling, B K Stefanowski, E Mansour, G A Ormondroyd
Characterization of biofilm formation on wood treated with vegetable oils by color-based image interpretation method
2015 - IRG/WP 15-40697
The protection of wood in order to extend its service life is an important issue nowadays. As an alternative to traditional wood coatings biofilms can be used. It is a living protective coating for the wood surface against UV and bio-degradation that has the ability to recover from local damage, such as cracks. This paper presents preliminary results of biofilm formation from an 8-month’s fie...
K Filippovych, H Huinink, L van der Ven, O C G Adan
Experimental Measurements of Fire Retardants on Plywood at Fire Test
2015 - IRG/WP 15-40709
The use and development of wood composite materials increased in the past few years. However, in Brazil there are some restrictions on these products regarding their use, since it could be considered a potential risk at a fire situation. Thus, becomes evident the need for researches aiming to fit these in safety standards. This study aims to evaluate the efficiency of two new fire retardant produc...
G C A Martins, L A Marcolin, J M Vidal, C Calil Jr
On the effect of climate and exposure conditions on durability indicators and their potential for service life prediction of wood-based products
2016 - IRG/WP 16-20576
In order to encourage increased use of wood, different user groups need to be better informed regarding the variation in performance between different wood materials and the effect of different use classes. It is also important to provide good empirical data on the service life of wood products as input to for example life cycle assessment studies. In the current study the effect of temperature an...
G Alfredsen, C Brischke, P-O Flæte, M Humar, L Meyer-Veltrup
Development of decay hazard maps based on decay prediction models
2016 - IRG/WP 16-20588
Durability plays a very central role in timber engineering, especially when working with wood in use class 3 and above where the risk of decay is high. As one of the primary decay influencing factors, the external condition, i.e. the local climate, is often graded by some type of climate index value. Predominately, climate indices are based on a direct relationship between weather data and decay. ...
J Niklewski, E Frühwald Hansson, C Brischke, D Kavurmaci
A non-VOC approach of solvent-based wood preservatives for remedial treatment
2016 - IRG/WP 16-30681
Solvent-based wood preservatives are the workhorses in the field of remedial treatment. Due to new European regulations on the indoor air quality there is an increasing pressure on the VOC-content on these solvent-based product types. The transfer of these European regulations into national law is left up to each European member state and handled in different ways. E.g. France has introduced a VO...
M Pallaske, S Hellkamp, P Jüngel
Fabrication and characterization of MicroPCMs filled wood-plastic composites: Effects of polyethylene glycol on melamine–formaldehyde shell material
2016 - IRG/WP 16-40728
Microencapsulated phase change materials (MicroPCMs) containing dodecanol were fabricated using melamine-formaldehyde (MF) or polyethylene glycol 200 modified melamine-formaldehyde (PMF) resin as the shell materials by in situ polymerization. Wood flour/high-density polyethylene (WF/HDPE) composites with MF shell MicroPCMs (MF-MicroPCMs) or PMF shell MicroPCMs (PMF-MicroPCMs) were prepared, respec...
Xi Guo, Jinzhen Cao
Enhancing wood properties through bio-based and non-biocidal co-polyesters
2016 - IRG/WP 16-40740
The commonly used wood preservation treatments are nowadays facing huge environmental issues, as well as increasing public concern. As regards those concerns, legislation tends to regulate the use of biocidal preservation chemicals.
Thus, it does appear crucial to provide alternatives to the use of biocides to allow different outdoor uses of wood such as for, posts, decking, and cladding or even ...
C L’Hostis, M-F Thévenon, E Fredon, P Gérardin
New perspectives for wood protection: enzyme-based treatments
2016 - IRG/WP 16-40742
Wood protection research is continuously looking for more benign and effective treatments. One of the main concerns deals with the toxicity of the active compounds employed in the formulations of the preservatives, since they could become a health and environmental issue. Secondly, long-lasting treatments are preferred in order to increase the service life of the treated wood. Weathering condition...
C Fernández-Costas, S Palanti, M Á Sanromán, D Moldes
Properties of Wood Plastic Composites Made of Recycled HDPE and Remediated Wood Flour from CCA/CCB Treated Wood Removed from Service
2016 - IRG/WP 16-40747
Chromated copper arsenate (CCA) and copper, chromium and boron (CCB) have been widely used in pressure treated wood as a heavy duty preservative to protect wood against insects and fungi for more than 60 years. Although many attempts have been done to solve the problems related to out-service treated wood, the problem still remains. Only a few studies were done to utilize the out-of service treate...
E D Gezer, S Akbaş, M Tufan, A Temiz
Fungal resistance and accelerated weathering of Wood-Plastic composites reinforced with Maritime pine wood flour
2016 - IRG/WP 16-40750
This study evaluates the durability of wood-polymer composites (WPCs) elaborated for use in cladding application from recycled polypropylene (rPP) and wood flour. Local Maritime pine wood flour derived from regional sawmills was used in the study to reduce the environmental impact associated with transport. Different wood-plastic ratios with and without UV stabilizers and biocide were tested. One ...
M Jebrane, T Fournier, N-E El Bounia, F Charrier-El Bouhtoury
Development of a new method for wood hydrophobizing and fixation of copper compounds by chemical hardening of vegetable based modified oils
2016 - IRG/WP 16-40754
Wood products with ground and direct water contact, but without sufficient biological durability, have to be protected against biological degradation by fungi and other microorganisms. Due to European legislation (Biocidal Products Regulation 528/2012), the selection of possible chemical agents, which are still allowed to be used, is diminishing rapidly. The use of previously widely applied, very ...
C Swaboda, M Fischer, K Jacobs
Improvement of wood properties by impregnation with liquefied spruce bark based resins
2016 - IRG/WP 16-40761
In this paper, biobased phenolic thermosetting resins are designed to be used as wood stabilization treatment. The originality of the study stands in substituting part of phenol by spruce (picea abies) bark: this is achieved by a liquefaction process in phenol in the presence of sulfuric acid as catalyst. Next, thermosetting resins are synthetized from liquefied bark by condensation on formaldehy...
X Duret, E Fredon, E Masson, P Gérardin
Lignin-Based Adhesive for Engineered Wood Products
2016 - IRG/WP 16-50319
Lignin as a naturally occurring polyphenolic compound has an excellent potential to replace petroleum-based phenol in formulation of phenol-formaldehyde adhesive that are used in manufacturing of engineered wood products. However, there are three major obstacles in application of polymeric lignin as phenol replacement: 1) low reactivity toward phenol, 2) high molecular weight, and 3) high polydisp...
I Kalami, M Arefmanesh, E Master, M Nejad
A Treatability Study of Western Wood Species with Water Based Azoles and Insecticides Using Buffered Amine Oxides
2016 - IRG/WP 16-40766
The use of Western U.S. Wood Species remains small in today’s global wood product market when compared to the use of other commercially available softwoods. One reason that other fiber sources, those that may be less naturally durable or exhibit slightly inferior mechanical properties, are utilized is ease of treatment. In an attempt to ensure adequate penetration in commercially important an...
R W Clawson Jr, C N Cheeks, K A Cutler
Liquefaction of woody waste: A novel approach in wood protection from CNSL based liquefied wood polyols
2017 - IRG/WP 17-30711
Liquefaction of lingo-cellulosic biomass is one of the thermo-chemical conversion processes for developing new materials, adhesives, preservatives and energy systems. The process also provides an opportunity to utilize waste wood such as saw-dust, woody wastes, branches and twigs for the development of value added products. Thus, this research paper deals with an investigation of antifungal and a...
A Kumar, G B.Nagarajappa, S Singh Chauhan
The use of new, aqueous chemical wood modifications to improve the durability of wood-plastic composites
2017 - IRG/WP 17-40787
The wood flour used in wood-plastic composites (WPCs) can biologically deteriorate and thus the overall mechanical performance of WPCs decrease when exposed to moisture and fungal decay. Protecting the wood flour by chemical modification can improve the durability of the wood in a nontoxic way so it is not harmful to the environment. WPCs were made with modified wood flour and then evaluated for m...
R E Ibach, C M Clemons, G C Chen
Treatability of beechwood railway sleepers with potential creosote substitutes
2017 - IRG/WP 17-40790
Maintenance of an efficient railway infrastructure still requires the use of wooden railway sleepers, particularly because wooden sleepers have more favourable properties for intensified vibrations than concrete or steel sleepers. Creosote, used for decades for the impregnation of railway sleepers, will possibly no longer be available for this application due to European legislation. This reveals ...
N Pfabigan, E Habla, R Gründlinger
Organosilicon-based impregnation hydrophobers for wood
2017 - IRG/WP 17-40808
The SILEX project “Improving sustainability of construction materials using innovative Silicon based treatment” is a Life+ project with reference LIFE+11 ENV/BE/1046 and started in April 2013. This project intends to demonstrate that a new class of compounds can be used for wood treatment for an extended service life combined with enhanced new testing methodology. The project aims at demonstra...
J-P Lecomte, J Van Acker, J Van den Bulcke, M Kutnik, M Montibus, S Salvati, S Derocker
Analysis of Wood Industrial Pollutants Based on Emission Coefficients
2017 - IRG/WP 17-50325
Accurate calculation and estimation pollutants is one of the basic tasks of environmental protection .The low carbon economy put forward However，low carbon economy data of wood industry is lack. The paper research on emissions and pollution of Chinese wood industry. The results showed dust emissions from much to least is: fiberboard, plywood and particle board; the amount of industrial ...
Chu Jie, Ma Ji, Zhangjing Chen
How carbon stored in harvested wood products contribute in a greenhouse gas accounting perspective
2017 - IRG/WP 17-50327
In 2014 the net annual removal by Norwegian forests was 30.4 mill ton CO2-eqvivalents while the emissions in other sectors was 53.2 mill ton CO2-eqvivalents. Hence, forests can play a major role in the national greenhouse gas balance. But forests also contribute to the carbon pool stored in wood products. The aim of this paper is, by using Norway as an example, to illustrate how the greenhouse gas...
G Alfredsen, G Søgaard
Review of Leaching Experiments of CCA-Treated Wood and Wood Treated with Copper-based Alternatives
2017 - IRG/WP 17-50330
The objective of this study was to compare leaching rates of various wood preservatives from treated wood and the tests used to gather this information. The preservatives compared included CCA and the copper-based alternatives, MCQ, ACQ, and MCA. The tests compared included AWPA E11, SPLP, TCLP, and environmental leaching tests. Among all of the tests evaluated, environmental tests most closely si...
A Jones, J Marini, H Solo-Gabriele
Liquefied wood polyols: Ecofriendly bio-based preservative for sustainable protection of wood from Termite attack
2018 - IRG/WP 18-10916
The major problems encountered in both indoor and outdoor utilization of wood are biological decay due to termite. The modification of wood with liquefied wood polyols has been found to be effective against termite attack. The liquefaction of wood aims to utilize woody wastes which are being generated during primary and secondary processing of wood in wood based industry. One of promising approach...
A Kumar, A John, T S Mehra, A K Pandey, S Singh Chauhan
Termite resistance of wood-plastic composites made with acetylated wood flour, coupling agent or zinc borate
2018 - IRG/WP 18-10917
There is little published scientific literature on the laboratory or field testing of wood-plastic composites (WPC) against termite attack. Therefore, the objective of this research was to investigate termite resistance (both laboratory and field) of 5 different extruded WPC blends of 50% western pine wood flour (WF) and high-density polyethylene (HDPE), and untreated pine solid wood. The study in...
R E Ibach, Y S Hadi, C M Clemons, S Yusuf