Your search resulted in 3098 documents. Displaying 25 entries per page.
Acetylation of pine wood in Uruguay
2022 - IRG/WP 22-40927
As a renewable material, wood is susceptible to decay by biologic (fungi, insects) and non biologic (water, radiation, mechanical wear, etc) agents. Such agents are controlled by using wood species of high natural durability, or by protecting the wood through drying, construction design, or the application of preservatives. The latter method has been and still is the most used in Uruguay, usually ...
C M Ibáñez, L Castillo
Durability against fungal decay of sorbitol and citric acid (SorCA) modified wood
2022 - IRG/WP 22-40928
Most European-grown wood species are susceptible to biological degradation, specifically, they suffer from a poor resistance against wood-destroying fungi. Therefore, prior to outdoor exposure, wood has to be treated either by applying a protective coating on its surface or by full-volume impregnation with antifungal chemicals. However, due to environmental and health concerns, the most frequently...
K Kurkowiak, L Emmerich, H Militz
Steam Pre-conditioning Treatment Prior to Acetylation: Impact on Dimensional Stability, Moisture Response Behaviour, and White-Rot Fungal Resistance of Hevea brasiliensis and Mitragyna ciliata Wood
2022 - IRG/WP 22-40930
The effect of steam pre-conditioning treatment on the dimensional stability, moisture response behaviour, and durability against white-rot fungus P. chrysosporium of acetylated Hevea brasiliensis and Mitragyna ciliata wood species were assessed. Defect-free specimens of both species from the top, middle, and base positions were selected, prepared according to ASTM D143-09 & ASTM D-2017 standards a...
E Uchechukwu Opara, J Mayowa Owoyemi, J Adeola Fuwape
Molecular dynamics investigation of wood modification with furfuryl alcohol
2022 - IRG/WP 22-40931
Molecular dynamics (MD) was applied to investigate and understand the structural characteristics and the interaction of cellulose and lignin with furfuryl alcohol for explaining the wood modification process. A single chain of cellulose polymer model and a softwood lignin model was considered to represent cellulose and lignin polymers. The obtained radial distribution function results revealed tha...
V Ponnuchamy, J Sandak, A Sandak
CIOL®-protection of wood – an update
2022 - IRG/WP 22-40932
Most commercial wood species from the northern European region are of low natural durability. Products from these wood species for outside applications need therefore protection to increase their service life. This protection should be free of biocides, come from renewable resource, have great performance and hold a low consumer price. A mixture of water, sorbitol and citric acid has the potential...
A Treu, E Larnøy, J Biørnstad
Surface chemical wood densification through in situ electron beam polymerization: description and dose study
2022 - IRG/WP 22-40933
Traditional wood chemical densification processes can be used to improve wood mechanical properties by increasing density of the material throughout its thickness. While mechanical surface densification has heavily been investigated, surface treatments involving impregnation of monomers remain unexplored. This study describes a new material, surface densified through lateral impregnation of acryla...
J Triquet, P Blanchet, V Landry
Comparative study of the properties of silicate coatings with different mineral pigments (titanium dioxide, iron (III) oxide, copper (II) oxide) on the surface of wood
2022 - IRG/WP 22-40936
Silicate coatings are attractive alternatives to conventional organic-based coatings for wood protection. In this work, silicate coatings were prepared with a potassium silicate binder modified with a methyl siliconate solution, and three types of mineral pigments titanium dioxide, iron (III) oxide and copper (II) oxide. The coatings were applied on beech wood and cured under ambient conditions. T...
A M Cheumani Yona, M Petrič
Premature adhesion failure of exterior wood coatings – The influence of substrate temperature at coating application and moisture accumulation during storage
2022 - IRG/WP 22-40937
The present study aimed at extending the knowledge about premature coating failures of industrially finished wood cladding. Two potential factors were studied: the influence of substrate temperature at coating application and moisture accumulation during storage on the adhesion of waterborne coating systems. In the first experiment, 4 batches of wood specimens were submitted to 4 different tempera...
U Hundhausen
Extraction of fungal colorants for their use in coloured coatings for wood
2022 - IRG/WP 22-40938
Microorganisms are highly interesting for the production of useful metabolites. Such metabolites are e.g. colorants, that can easily be produced on industrial scale and low material costs. To date some microbial produced colorants are used in textile- and food industry because of their low toxicity and sustainability compared to synthetically produced colorants. However, little is known about the ...
K Kusstatscher, N Pfabigan, M Senoner, L Orlowsky, A Steitz, B Forsthuber, S Niedermayer, R Gründlinger
Optimized composition of alkyd emulsion with nanoparticles of iron oxide for enhancing protection of thermally modified wood
2022 - IRG/WP 22-40940
Thermal treatment is acknowledged as an environmentally friendly method to improve durability of wood and some of its properties, such as biological resistance, dimensional stability, reduced hygroscopy. Despite these improvements, when used outdoors, also thermally treated wood is subjected to the action of environmental factors, like solar radiation, moisture, precipitations, temperature, etc., ...
E Sansonetti, D Cīrule, I Andersone, B Andersons, E Kuka
Effect of nano-particle characteristics and concentration on UV protection of timber: A field exposure test
2022 - IRG/WP 22-40941
Wood has a well-known susceptibility to ultra-violet light degradation, leading to premature replacement. A variety of products have been developed to protect against this damage, but most provide less than 12 months of protection and must be regularly reapplied. Developing improved coatings would help reduce wood losses and reduce maintenance costs. Nano-particles have a variety of attractive pro...
T Yi, J J Morrell
The influence of thermal modification and surface charring to different levels on wettability of Norway spruce wood
2022 - IRG/WP 22-40942
The wood can alternatively be protected from water absorption by thermal modification and charring. Both techniques cause certain chemical and physical changes in the wood, the extent of which depends on the level of temperature applied. The objective of this study was to determine how the combination of charring to different levels and thermal modification affects the chemical, morphological, and...
J Žigon, C Gerardin, M E P Wålinder, P Gerardin
Evaluation of the physical properties of heat-treated native Peruvian woods for their application as coverings in buildings located in in arid, semi-warm and humid climates
2022 - IRG/WP 22-40943
Wood is a material that has properties suitable for its use in construction: as a structural component, cladding or decorative element, however, it is necessary to have knowledge of its physical, mechanical and thermal properties in order to have a logical criterion when applying it. It is known that wood has hygroscopic properties, so it tends to absorb the relative humidity of the natural enviro...
K Ayala Castro, A Loayza Argüelles, V J Pilco Mamani
The Resistance of Some Commercially Thermally Modified American Hardwoods to Termites and Fungi
2022 - IRG/WP 22-40944
Thermally Modified Wood (TMW) is now being produced in the United States but there are few data on the durability of these materials. In this study, commercially-produced thermally modified yellow poplar (Liriodendron tulipifera), red maple (Acer rubrum), and white ash (Fraxinus americana) were evaluated for fungal and termite resistance. The resistance of the three TMW species against Gloeophyllu...
B Cortes, B Bond, A Taylor, J Lloyd
Mechanical Properties of Thermally Modified Wood after twelve Months of Field Exposure
2022 - IRG/WP 22-40945
This study aimed to evaluate the durability and mechanical properties of two different woood species, namely beech (Fagus sp.) and silver fir (Abies alba), from Bosnia and Herzegovina thermally modified at three different temperatures and duration at maximum temperature. Samples of the mentioned wood species wood (Abies alba) were prepared according to EN 408+A1 standard. The maximum 4-point bendi...
R Hasanagić, M Bahmani, L Fathi, M Humar
Effect of densification of Eucalyptus nitens and E. obliqua on moisture uptake, swelling, decay resistance, and fire performance
2022 - IRG/WP 22-40946
Some Australian Eucalyptus species that are abundantly available have low natural durability and poor resistance to fire. These same species are also extremely difficult to treat with preservatives or fire retardants using conventional pressure treatment methods due to a large proportion of refractory heartwood. The aim of this research was to understand whether thermo-mechanical densification had...
B Hassan, J J Morrell, F Wiesner, W Wu, B Belleville, K C Wood
Improving wood durability by mineralisation and thermal modification
2022 - IRG/WP 22-40948
A significant increase in the fungal durability of wood was achieved by using a modification procedure combining two environmentally friendly methods: thermal modification and mineralisation. It offers an ecological alternative to other biocidal treatments. European beech (Fagus sylvatica) and Norway spruce (Picea abies) were selected as model wood species and exposed to four different fungi: Gloe...
R Repič, A Pondelak, D Kržišnik, M Humar, A S Škapin
Durability of thermotreated Pinus sylvestris and Eucalyptus nitens against wood decay organisms
2022 - IRG/WP 22-40949
One of the alternative treatments to avoid the application of biocides is thermal modification of wood, which increases the durability of wood against attack by wood decay organisms. The durability of Pinus sylvestris and Eucalyptus nitens thermotreated at 180 and 212 ºC, was studied. The results show that thermotreatment against wood decay fungi in P. sylvestris is slightly more effective than i...
M T Troya, S M Santos, L Robertson, N Pérez-Molina, V Baños, A Dieste
Joints design considerations in indoor high humidity conditions
2022 - IRG/WP 22-40950
In recent years, a number of cases of degradation by wood destroying fungi have been detected in covered timber structures such as pools, wineries, bathrooms, etc. – in fact, any building where indoor air may reach high humidity values during certain periods of time.
The origin of this kind of decay was not related to water leaks, but to the condensation of the water vapor over the steel connec...
A Lozano, D Lorenzo, M Alonso, F Álvarez, J E Martínez
Influence of weathering on the mechanical properties and performance of exterior wood coatings
2022 - IRG/WP 22-40951
Three commercial coatings were exposed to artificial (EN 927-6) and natural weathering (EN 927-3) on wood samples. Cracking was visually assessed as well as Persoz hardness. Free films of the same coatings were also exposed to the same weathering tests before their tensile properties were measured. Results show that artificial and natural weathering modified the overall mechanical properties of wo...
L Podgorski, J-D Lanvin
Phenol formaldehyde modification and termite resistance under laboratory testing
2022 - IRG/WP 22-40952
The development of phenol formaldehyde (PF) resins as a means of impregnating solid wood is one that has been explored for several decades, both in terms of conventional impregnation processing (Impreg) or compressional impregnation (Compreg). However, it is only recently with advances in processing conditions that the method truly affords a means of achieving conventional modification for solid t...
L Nunes, A Pitman, M Duarte, B Stefanowski, D Jones
Durability of thermally modified western hemlock lumber against wood decay fungi
2022 - IRG/WP 22-40954
The chemical modification of wood is gaining popularity as a treatment to increase wood durability in the United States. Further standardization and testing of thermally modified North American species is needed to optimize the production of thermally modified products from regionally available resources. This work measures the impact of thermal modification of western hemlock lumber durability ag...
G Presley, J Cappellazzi, I Eastin
Evaluation of Decay Resistance for the Larch Wood Heat-treated with Superheated Steam
2022 - IRG/WP 22-40956
Heat-treatment of wood is a process that involves applying heat ranging 160–260°C to improve its physico-mechanical properties and resistance against wood rot fungi. The level of the changes in the wood properties by heat-treatment differs depending on the temperature and duration of heat-treatment, as well as the types of heat transfer media used for heat-treatment. The heat-treatment on wood ...
Y Park, S-M Yoon, H Kim, W-J Hwang
Biocomposites based on PVA, cellulose nanofibrils and tannic acid
2022 - IRG/WP 22-40957
Biocomposite films based on a polyvinyl alcohol (PVA) with the addition of cellulose nanofibrils (CNF) as a reinforcing component and with the addition of the biologically active tannic acid (TA) were prepared. The influence of different additions of CNF and TA in the polymer matrix PVA on the mechanical properties, improvement of hydrophobicity of the prepared films was studied. In all cases, the...
U Osolnik, V Vek, I Poljanšek, Poven
The influence of climate changes on Central European forests with an emphasis on Slovenia
2022 - IRG/WP 22-50368
When forests are managed sustainably, they play an essential role in protecting climate and biodiversity. They protect soils and water resources, provide livelihoods, and contribute to the well-being of rural and urban communities. European forests are multifunctional and provide a range of ecosystem services. These include the production of renewable materials that can replace materials with a la...
J Gričar, L Krajnc, M Westergren, S Rus, H Kraigher