Your search resulted in 3419 documents. Displaying 25 entries per page.
Incorporating insect behaviour in standard tests of wood preservatives - A possible way to reduce pesticide loadings
2000 - IRG/WP 00-20190
The application of wood preservatives to protect timber against insect infestation is common practice world wide. The effectiveness of wood protecting insecticides is usually determined in various standard tests. Depending on the target pest species and the test method, larvae of different developmental stages and sizes or adult insects are exposed artificially to the insecticide-treated commodity...
H Hertel, R Plarre
Heat treated timber in Finland
2000 - IRG/WP 00-40158
Heat treatment permanently changes the physical and chemical properties of wood by means of high temperatures (150 - 240°C). Heat treatment darkens the colour of the wood. Heat treatment improves the equilibrium moisture content of the wood and the shrinkage and swelling of the wood is reduced. Very high temperatures improve the resistance to rot and also reduce the susceptibility to fungal decay...
T Syrjänen, E Kangas
The leachability and specificity of the biological protection of timber using Scytalidium sp. and Trichoderma spp
1986 - IRG/WP 1302
The results of field experiments, using biological control against internal decay of creosoted poles, are briefly reviewed and the evidence concerning the leachability of the antibiotics produced by these species is presented. A pure culture miniblock decay test on biological control treated pine sapwood is described and the results compared to previously published data. The protection against Len...
P I Morris, N A Summers, D J Dickinson
End grain sealants for wood preservation studies
1985 - IRG/WP 3341
The results of tests with possible end grain sealants for wood preservation studies are reported. The epoxy resins used gave satisfactory performance on wet or dry Sitka spruce and have been used with success for diffusion treatment studies....
R J Murphy, N A Summers
Status of the Working Group on Preservation of Wood in the Marine Environment - Questionnaire results
1977 - IRG/WP 434
At the joint meeting of the IRG and COIPM dealing with preservation of wood in the marine environment, it was suggested that a Marine Group should be formally recognised within IRG. It was agreed that a questionnaire (Document No: IRG/WP/424) should be circulated to determine the views of the membership on the future status of this group. The results of this questionnaire are presented....
R A Eaton
A collaborative test to determine the efficacy of poyurethane coatings on wood samples exposed in the marine environment. 1st Interim Report
1988 - IRG/WP 4145
Wood samples coated with elastomeric polyurethane (ca. 50 mils thick) were exposed for up to 2 years in 12 tropical and temperate marine test sites with known teredinid, pholad and/or crustacean infestations. All uncoated control samples were destroyed or partially destroyed. Polyurethane-coated samples were not attacked, the surfaces of the coating were sound and the polyurethane adhered well to ...
R A Eaton
Sap displacement treatment of utility poles in Papua New Guinea
1977 - IRG/WP 3102
Rapid growth of rural electrification in P.N.G. has created a considerable demand for treated poles. In the past power lines have been run on steel poles but the Government of P.N.G. is now seeking to make maximum use of the country's own resources rather than continue to rely upon imported materials such as steel poles. To some extent, this demand is being met by expansion of existing va...
C R Levy
Antifungal properties of new quaternary ammonium and imidazolium salts against wood decay, staining and mould fungi
2004 - IRG/WP 04-30347
The biological activity of twenty-four potential wood preservatives – imidazolium and quaternary ammonium salts with a modified anion structure was determined employing screening agar-plate and agar-block methods. Experiments were carried out on Scots pine (Pinus sylvestris L.) wood. The aim of the performed studies was to investigate the effect of structure modification of IC and QAC with organ...
J Zabielska-Matejuk, W Wieczorek
Environmental behaviour of treated wood in (semi-)permanent contact with fresh or seawater
1998 - IRG/WP 98-50101-20
This study presents a strategy for the environmental toxicity evaluation of treated wood towards the aquatic compartment, using non target water organisms toxicity tests. A lixiviation process is applied on wood (Pinus sylvestris) treated with several wood preservatives formulations. The lixiviation process is carried out in the laboratory with ultrapure water or synthetic seawater.
After chemica...
P Marchal, C Martin
Available iron promotes brown rot of treated wood
1992 - IRG/WP 92-1526
Exposure of treated wood blocks to rusting iron increased the toxic threshold of chromated copper arsenate and ammoniacal copper arsenate to a brown-rot fungus Leucogyrophana sp. This supports the hypothesis that the movement of iron ions into wood contributes to the unexpectedly high decay rate of treated wood at the stake test site at Westham Island BC. To what extent this phenomenon may occur e...
P I Morris
Preliminary note on the fungal problem of rubber wood
1983 - IRG/WP 3246
Susceptibility of rubber wood to fungal attack limits its wider utilisation. Fungal problems encountered in treating rubber wood with boron compounds by diffusion process have been discussed. Sodium pentachlorophenoxide and 2-thiocyanomethylthio benzothioazole (TCMTB) were investigated for possible control of fungal growth during diffusion storage and their performance has been reported....
R Gnanaharan
An experimental method to simulate incipient decay of wood by basidiomycete fungi
2000 - IRG/WP 00-20200
At very early stages of decay of wood by basidiomycete fungi, strength loss can be measured from wood before any measurable weight loss. Therefore, strength loss is a more efficient measure of incipient decay than weight loss. However, common standard decay tests (e.g. EN 113 or ASTM D2017) use weight loss as the measure of decay. A method was developed that allowed progressive removal of samples ...
S F Curling, J E Winandy, C A Clausen
Leaching of inorganic wood preservatives – Investigating the relationship between leachability, dissociation characteristics and long-term leaching potential
2003 - IRG/WP 03-50199
Estimation of the leaching properties of preservative components is greatly affected by the leaching test method applied since not all methods equally consider the physical components responsible for leaching. These include: wetting of the wood and penetration of water (affected by dimensions, amount of end grain, permeability, duration and nature of water exposure); solution of preservative comp...
L Waldron, Y T Ung, P A Cooper
Laboratory experiments on aerial emissions from wood treated with wood stains
1993 - IRG/WP 93-50001-06
Due to the actual environmental interest in wood preservation, a series of experiments was carried out on the emission of biocides from treated wood. The research focussed on the volatilization of 5 biocides from boards treated with wood preservative finishes containing dichlofluanide (DCF) azaconazole (AZA), pentachlorphenol (PCP), iodopropynylbuthylcarbamate (IPCB) and tributhyltinoxide (TBTO). ...
G M F Van Eetvelde, M Stevens
The development of a screening method for the activity of pyrethroids against wood boring marine crustaceans, Limnoria spp
1978 - IRG/WP 443
The present work is concerned with the develepment of a suitable bio-assay technique to determine the biological activity (contact action) of pyrethroids against Limnoria spp. Estimates of the toxicity of three pyrethroids, permethrin, cypermethrin and decamethrin (the structures of which are shown in Fig. 1.) to the marine borer have been obtained....
D Rutherford, R C Reay, M G Ford
The Biocidal Products Directive ( 98/8/EC ) - its consequences for the wood preservation industry
2001 - IRG/WP 01-50166-04
1. The Current Position
This European Union Directive is one of the most technically complex pieces of legislation that has been developed by the European Commission (EC). Although the Directive was to have been implemented in the legislation of individual Member States of the EU by May 2000 progress has been slow. A number of Member States have yet to declare the Competent Authority who will handle their legislation. The body text of the Directive cannot stand-alone and is dependent on ancillary regulations and the development of technical guidance for both the Competent Authorities in the Member States and also industry to understand their roles in the whole process for the regulation of biocides and the biocidal products containing them. The process is far from complete in terms of a piece of workable legislation and this leaves not only industry but also the Competent Authorities with significant areas of uncertainty. This is potentially economically and socially damaging to the marketing and use of biocides and biocidal products. Because of this evolutionary process this paper can only be written in general terms as by the time the symposium takes place some significant changes to the position at the time of writing may have occurred.
2. Background
The Biocidal Products Directive (98/8/EC), (BPD), is a directive which requires that biocides ( as active substances) are approved for use within the EU and the individual biocidal products containing these active substances are approved for use by the Competent Authority(s) of the Member State(s) in which it is intended to market the product. The product authorisation obtained in the first Member State should be mutually recognised by the other Member States in which application for authorisation to place the product on the market is sought. The Directive has to be seen in the context various other Directives, notably the Plant Protection Directive 91/414/EC). Biocidal products are grouped in the directive into twenty three "product types" and wood preservatives are Product Type 8. The intention of the directive is to harmonise the requirements for the placing of biocidal products and active ingredients on the market throughout the EU. EU wide use of so-called Common Principles are intended to be used to assess the dossiers in order to achieve a common approach and eliminate the current situation where individual Member States apply their own particular national approaches and criteria in the assessment and regulation of products . Annex IIA of the directive identifies the data requirements for the active substance and Annex II B for the biocidal product. There are additional data requirements identified in Annexes IIIA and IIIB for each product type reflecting potential for exposure to man and the environment.
3. Entry onto Annex I
Any new active substance will require approval before it or any biocidal products including it can be placed on the market. The dossier to be submitted to the EC will have to include additional data and risk assessments for the product types (as defined in the BPD) in which it will be intended to be used. For those active substances that are accepted as being existing substances on the market before May 2000 (say in wood preservatives) these will be ranked and prioritised. This process is being defined in the so-called: Review Regulations.
4. An environmental directive
There is no doubt that this Directive has a high environmental content in terms of the data and the associated risk assessments which are to be prepared. The protocols and the end points for some of these data requirements are still being developed. In general the EC considers that modelling exposure using human and environmental exposure scenarios covering the end use of the product is an acceptable approach . Data are required to enable these scenarios to be modelled and risk assessments made. It is necessary that regulators do not make decisions based on hazard assessment alone in the absence of fully worked out and agreed emission scenarios to define exposure levels which generate a realistic worst case risk assessment. Risk is a function of both hazard and exposure. A lot of work has been done in the development of Technical Notes for Guidance intended to help the regulator and the applicant in the submission and the interpretation of the data. Whilst it may be the case that the human toxicity data requirements still leave questions to be answered it is in the environmental aspects part of the regulatory process where there is still much work to be done. The Directive would seem to rely heavily on the development of Pass / Fail criteria in simulation tests. This is a big subject and of key importance to the risk assessment.
5. Wood preservatives ---- a test case
Wood preservation has achieved a certain reputation. On the one hand it is said that a prime reason for the development of the Biocidal Products Directive arose from European problems in the regulation of the marketing and use of dangerous substances, notably wood preservatives. On the other hand because wood preservatives have been regulated by a number of Member States for many years it is believed they are well understood. The EC and the Member States also wanted to be seen to have achieved early success in the implementation of the Directive therefore the decision was taken to start, following failings with the speed of progress of the Plant Protection Products Directive, with a product type they knew all about i.e. wood preservatives. There is no doubt that there is a much greater understanding on the exposure scenarios, both human and environmental, for wood preservatives than many other product types. However, would it not have been better to have tackled some of the other product types where such an understanding is much less well developed? It is regrettable that the EC and Member States did not feel able to accept the results of an EC sponsored study (Haskoning report) on the assessment of risks for all the product types covered under the BPD. The results of this study clearly showed that wood preservatives did not constitute the most significant risk to man or the environment and in fact the risk was significantly greater for other product types.
6. Wood preservatives and the OECD Biocides Programme
Another speaker will be covering this subject in more detail. Suffice it to say that because of the perception there was good knowledge about wood preservatives again they were selected as the pilot for an OECD project looking at environmental and human exposure assessment under the OECD Biocides Programme. The findings from two OECD Workshops actually demonstrated there was still much to be learnt about wood preservatives in order to refine the risk assessments to a state where they would be sufficient for the requirements of the BPD. This work is ongoing but it clearly demonstrates the problems that both the regulator and industry will have in the preparation and the assessment of the dossiers for both the active substances and the biocidal products. This is especially the case for other biocidal products that have not been subject to the same kind of regulation that wood preservatives have subjected to in the past.
7. Inorganic and organic biocides
With current wood preservation technology there is still a dependence on inorganic chemicals such as copper (in conjunction with other biocides) or with chromium, as well as arsenic and boron for many end use applications. This is very much the case where a long term service life is a key factor in the use of treated wood for that end use. These substances are commodity chemicals and are also covered under the Existing Substances Regulations (EC) 1488/94. There is also work going on revising the Technical Notes for Guidance covering them . This includes a significant addition in the environmental risk assessment area. Efforts are being made to integrate and coordinate the requirements for both the BPD and the Existing Substances Regulations and OSPAR ( OSPAR Convention for the Protection of the Marine Environment of the North-East Atlantic). OSPAR refers to the Oslo Paris Convention. Whilst the BPD seems primarily aimed at the regulation of biocides based on organic chemicals wood preservative products may contain both inorganic and organic components. Indeed there are probably few wood preservative formulations on the market that contain only one active substance. This must have a significant impact on the way the dossiers are prepared for the active substance and the biocidal products and how they are assessed both at the EC and the Member State level.
8. Consequences of the BPD for the wood preservation industry
Whilst this paper addresses the consequences for the wood preservation industry per se, it must not be overlooked that there may be implications for the fabricaÈors of articles made from treated timber. Some current wood preservative formulations may over a period of time be withdrawn from the market because the risks and costs of generating the data and the preparation of the dossier make the product economically unviable. The presence of large working volumes of wood preservative solutions at treatment plants requires realistic withdrawal periods to avoid the unnecessary disposal and associated environmental risk of products that have been used satisfactorily for many years.
9. Availability of active substances
The structure of the industry has changed dramatically in the past few months and there is no doubt that other changes both within and outside the wood preservation industry itself are yet to happen. The original differentiation between formulator of wood preservatives and active substance suppliers to the wood preservation industry has become blurred. Some of the active substances used in wood preservation are used in other either other biocidal product types or in products regulated under another directive, e.g. Plant Protection Products Directive 91/414/EC.
10. Data protection
This continues to be a key issue for industry and some companies may find it strategically or financially necessary not to support an active substance in a particular product type thus leaving that sector without being able to use the active substance. The coming months will start to reveal which active substances are likely to be supported, at least through the notification process. Formulators are therefore in a close dialogue with their suppliers to try to determine their intentions on whether or not they intend to support their active substance. Today's wood preservative formulations are largely multi active substance based. Product costs, efficacy spectra, niche marketing and other considerations have made this process inevitable. New wood preservative formulations take time to research and develop and the continuity of availability of a choice of active substances is of key importance. A lack of adequate return on investment necessary to sustain the development of new products could have a negative impact on innovation and the rate of introduction of new products. It is extremely unlikely that any new active substance will be solely developed for use in wood preservation. This would be an effect contrary to expectations of the EC. The situation with wood preservatives is complicated by the fact that treated wood is a construction product and comes under the scope of the Construction Products Directive (89/106/EEC) (CPD). Products under the scope of the CPD are required to meet certain so-called essential requirements and one of these is durability. Demonstration of compliance involves the extensive suite of CEN wood preservative efficacy tests. Even relatively small changes in formulations may require extensive re-testing under the EN 599 regime in some Member States.
11. Task Forces
Companies are encouraged by the EC to enter into Task Forces in order to reduce the burden of testing on animals and also to reduce the number of dossiers to be reviewed for each active substance. Ideally, and understandably, the EC would like one dossier per active substance. Parts of the wood preservation industry have been co-operating in Task Forces and much practical experience has been gained. Even closer co-operation will be required and this will enable companies to pool experience and expertise and manage their financial exposure to potentially high regulatory costs by sharing them amongst a larger number of parties.
12. Financial aspects
Industry will have to make some best guesses with respect to its investment programmes for supporting its portfolio of products. Formulators and active substance suppliers are likely to group into Task Forces in order to reduce their costs in terms of data generation and the fees likely to be charged at the EU and the Member State level for the assessment of the dossiers. The compilation of the dossiers requires specialist expertise to assist the industrial applicant(s). This is likely to cost in the order of £100,000 per active substance, not including the costs of generating any data. The Rapporteur State's costs for reviewing the dossier is also expected to be of the same order. Clearly these kinds of costs will impact on innovation. An adequate payback must be available to the company to justify this level of investment.
13. Will mutual recognition work?
Member States are required to recognise the authorisation of the biocidal product placed on the market in the first Member State when subsequent applications are made to place the product on the market. This is a fundamental principle of the BPD, although there is concern that Member States continue to have enough flexibility to prevent this happening if there are particular concerns in that Member State. Industry very much hopes this will not be the case and that mutual recognition, a fundamental principle of the BPD, will work in practice.
14. Environmental aspects
Biocidal products such as wood preservatives are generally applied in controlled situations and not over large areas. Consequently any emissions can be considered to be from discreet sources, such as treated timber or potentially from timber treatment plants. This is in contrast to plant protection products and some other biocidal products that are usually dispersed over a relatively large area. Because of this a lot of work is required to be done to re evaluate how the environmental aspects of biocidal products such as wood preservatives can be assessed in an objective manner. The criteria that define an emission and how the PEC (Predicted Environmental Concentration) for each environmental compartment is determined are critical. The wood preservation industry, through the EWPM (European Wood Preservative Manufacturers Group), has been working with institutes and other interested parties in a co-operation known as the EFG (Environment Focus Group) to progress the development of appropriate methodology. Data will be required for both primary and secondary exposure to treated timber. The protocols for this work are yet to be agreed. This work is being further progressed in the OECD together with input from CEN TC 38 WG27. This co-operation between the OECD and CEN is extremely significant in that it is, I believe, the first time such a co-operation has taken place in the development of an OECD Guideline. If one considers all of the end uses where treated timber may be found carrying out a risk assessment with few guidelines on how it should be done is a very uncertain process for both industry and the regulator. Reliance on so-called expert opinion may be inadequate.
15. Comparative assessment (the substitution principle)
This is a process whereby the health safety and environmental properties of acti_u101 ? substances used in the same product type could be compared and those with the most undesirable properties would not be placed on Annex I. Consequently biocidal products containing them would have to be removed from the market. This process is embodied in the BPD but it was initially considered that it would only be applied in the event of problems arising with active substances or products containing them rather than being used as a screening tool early on in the review process for active substances. This area is still an uncertain one with Member States having different interpretations of this principle. It is unfortunate that the wood preservation industry could be used to test out this concept at a European level. The consequences of this principle could be further losses of active substances available to the wood preservative formulators.
16. Substances of concern
The BPD is not only concerned with the active substances that are formulated into the biocidal product but also with so-called "substances of concern". These are defined as any substance, other than the active substance, which has the inherent capacity to cause an adverse effect on humans, animals or the environment and is present or is produced in a biocidal product in sufficient concentration to create such an effect. There are significant implications for the formulator of the biocidal product . The formulator may have to submit an extensive dossier containing toxicological and metabolic as well as ecological data on each of the substances of concern when seeking approval for the biocidal product. There may be classes of compounds that become unavailable to the formulator either because of the risks posed by the co-formulant or because the cost of generating data will be uneconomic.
17. The wood preservation Industry's view on the BPD
Industry has supported the development of the BPD since its conception in 1989. It is still supportive it but believes that the degree of complexity is disproportionate to the level of risk when it comes to wood preservatives. After all wood preservatives have been regulated for a long time and in reality there have been few significant health safety and environmental problems associated with them. Industry believes there is no need to determine an absolute understanding about a biocide and its application but rather there is a need to determine the level of understanding that will enable characterisation so that a risk assessment can be made. The wood preservation industry has sought either directly or through representative bodies a pro-active and collaborative approach with the regulators although at times this appears to have encouraged inappropriate demands. The regulators have invariably responded positively to this however they may not always understand the burden in both time and resource in having made wood preservatives the test case. Industry hopes that its efforts to be pro-active will be recognised and will be dealt with equitably when considered before the other product types defined in the Biocidal Products Directive.
D Aston
Developments in wood preservation
1978 - IRG/WP 3121
The purpose of this paper is to comment very briefly upon recent developments and trends in wood preservation so that members of this Working Group have a basic knowledge of activities in other countries. The last paper was prepared in September 1977 and the present paper refers to developments since that time....
B A Richardson
Disposal of Pressure Treated Wood in Construction and Demolition Debris Landfill
2005 - IRG/WP 05-50235
Pressure treated wood is often disposed in landfills in the US, very frequently in construction and demolition (C&D) debris landfills. C&D debris disposal facilities in many states are not equipped with liner systems to protect underlying groundwater. In this paper, issues associated with the disposal of metal-containing treated wood in C&D debris landfills are discussed. C&D de...
T G Townsend, B Dubey, J Jambeck, H M Solo-Gabriele
Quality control of microwave treatment of timber after dry rot attack
2001 - IRG/WP 01-40205
In Denmark microwave treatment of timber has been used during the last 15 years for eradication of dry rot (Serpula lacrymans). About 1500 microwave treatments have been employed in coorporation with Hussvamp Laboratoriet. Previously all the infected timber was removed plus an extra metre as a safety zone. This meant that all casting boards and plaster had to be removed as well and joists replaced...
J Bech-Andersen, J Andreasson, S A Elborne
Disposal of CCA treated waste wood by combustion - An industrial scale trial
1996 - IRG/WP 96-50068
Totally 272 m³ (62.7 t) of CCA treated utility poles were chipped and incinerated at Jalasjärvi Gasification Plant. In average the whole batch of chips contained 57 kg of elementary copper, 95 kg chromium and 76 kg arsenic. During the 56 h combustion trial the measured arsenic emission to the air was 76 g in total. Copper and chromium emission was less than 1 g. The condensing water from the coo...
A J Nurmi
Ancillary properties of vapor boron-treated composites
2001 - IRG/WP 01-40210
This paper discusses the water absorption, thickness swelling, and internal bond strength of North American composites treated using a vapor boron treatment process. For oriented strandboard, high boron loadings led to lower internal bond strength and lower thickness swelling. Water absorption results were variable but no deleterious effect of treatment was noted. For medium density fiberboard, th...
W A Jones, H M Barnes, R J Murphy
Germination of basidiospores on preservative treated wood after leaching or natural weathering
1981 - IRG/WP 2150
In tests of residual toxic efficacy after leaching or natural weathering, spore germination with Gloeophyllum trabeum has proved to be a less reliable criterion of attack than when used with unaged preservative treatments. Since spores sometimes prove more tolerant than their parent mycelium, their use should be continued....
J K Carey
Report of activity of CEN/TC 38: Test Methods for Wood Preservatives
1987 - IRG/WP 2287
G Castan
The proposal for optimalization of the agar-block method for wood preservatives fungitoxic evaluation
1995 - IRG/WP 95-20065
On the base of own research and other scientists results the proposal for optimalization of agar-block method was presented by:
- selection of test fungal species and strains and central distribution of their pure cultures,
- change of the treatment and control samples exposure procedure,
- application of mathematical estimation of toxic value results,
- shortening the duration of fungitoxic t...
J Wazny
Correlation between a laboratory bioassay and field trial conducted to determine the termiticidal effectiveness of bifenthrin
2002 - IRG/WP 02-20248
Details are given of a laboratory bioassay and field trial undertaken to determine the termiticidal effectiveness of the synthetic pyrethroid bifenthrin, when impregnated into Pinus radiata D. Don sapwood specimens. Results show a strong correlation between the laboratory and field methods of evaluation. Protection threshold limits obtained were the same for the two test species of termite employe...
J W Creffield, K Watson