Your search resulted in 3575 documents. Displaying 25 entries per page.
Optimized composition of alkyd emulsion with nanoparticles of iron oxide for enhancing protection of thermally modified wood
2022 - IRG/WP 22-40940
Thermal treatment is acknowledged as an environmentally friendly method to improve durability of wood and some of its properties, such as biological resistance, dimensional stability, reduced hygroscopy. Despite these improvements, when used outdoors, also thermally treated wood is subjected to the action of environmental factors, like solar radiation, moisture, precipitations, temperature, etc., ...
E Sansonetti, D Cīrule, I Andersone, B Andersons, E Kuka
Evaluation of the physical properties of heat-treated native Peruvian woods for their application as coverings in buildings located in in arid, semi-warm and humid climates
2022 - IRG/WP 22-40943
Wood is a material that has properties suitable for its use in construction: as a structural component, cladding or decorative element, however, it is necessary to have knowledge of its physical, mechanical and thermal properties in order to have a logical criterion when applying it. It is known that wood has hygroscopic properties, so it tends to absorb the relative humidity of the natural enviro...
K Ayala Castro, A Loayza Argüelles, V J Pilco Mamani
Effect of densification of Eucalyptus nitens and E. obliqua on moisture uptake, swelling, decay resistance, and fire performance
2022 - IRG/WP 22-40946
Some Australian Eucalyptus species that are abundantly available have low natural durability and poor resistance to fire. These same species are also extremely difficult to treat with preservatives or fire retardants using conventional pressure treatment methods due to a large proportion of refractory heartwood. The aim of this research was to understand whether thermo-mechanical densification had...
B Hassan, J J Morrell, F Wiesner, W Wu, B Belleville, K C Wood
Improving wood durability by mineralisation and thermal modification
2022 - IRG/WP 22-40948
A significant increase in the fungal durability of wood was achieved by using a modification procedure combining two environmentally friendly methods: thermal modification and mineralisation. It offers an ecological alternative to other biocidal treatments. European beech (Fagus sylvatica) and Norway spruce (Picea abies) were selected as model wood species and exposed to four different fungi: Gloe...
R Repič, A Pondelak, D Kržišnik, M Humar, A S Škapin
Durability of thermotreated Pinus sylvestris and Eucalyptus nitens against wood decay organisms
2022 - IRG/WP 22-40949
One of the alternative treatments to avoid the application of biocides is thermal modification of wood, which increases the durability of wood against attack by wood decay organisms. The durability of Pinus sylvestris and Eucalyptus nitens thermotreated at 180 and 212 ºC, was studied. The results show that thermotreatment against wood decay fungi in P. sylvestris is slightly more effective than i...
M T Troya, S M Santos, L Robertson, N Pérez-Molina, V Baños, A Dieste
Durability of thermally modified western hemlock lumber against wood decay fungi
2022 - IRG/WP 22-40954
The chemical modification of wood is gaining popularity as a treatment to increase wood durability in the United States. Further standardization and testing of thermally modified North American species is needed to optimize the production of thermally modified products from regionally available resources. This work measures the impact of thermal modification of western hemlock lumber durability ag...
G Presley, J Cappellazzi, I Eastin
Evaluation of Decay Resistance for the Larch Wood Heat-treated with Superheated Steam
2022 - IRG/WP 22-40956
Heat-treatment of wood is a process that involves applying heat ranging 160–260°C to improve its physico-mechanical properties and resistance against wood rot fungi. The level of the changes in the wood properties by heat-treatment differs depending on the temperature and duration of heat-treatment, as well as the types of heat transfer media used for heat-treatment. The heat-treatment on wood ...
Y Park, S-M Yoon, H Kim, W-J Hwang
Novel bio-based tannin/furfurylic alcohol thermosets: application to wood preservation
2022 - IRG/WP 22-40959
This project is integrated within the overall context of sustainable development and targets the valorization the wood industry by-products such as polyphenolic extractives, and in particular tannins. The objective targets the use of the same polymer used for production of tannin-furanic foams, but here for wood preservation to avoid the utilization of biocides. The aims is to the design of copoly...
C Gérardin-Charbonnier, E Azadeh, A Pizzi, P Gerardin
Assessment of the Material Durability and Structural Integrity of the Wooden Velodrome in Češča vas, Slovenia
2023 - IRG/WP 23-11012
Wood is a widely used material in the construction industry, and it has been utilized for thousands of years to create buildings and other structures. When wooden structures are designed, built, and maintained properly, they can be safe and long-lasting. Sports facilities, which provide athletes with a space to train, compete, and improve their abilities, are crucial in creating a strong and susta...
D Kržišnik, M Humar, B Lesar
Natural durability of 9 tropical species suitable for round wood timber building: fungi and termites laboratory screening tests
2023 - IRG/WP 23-11013
In numerous tropical forest species, wood properties are poorly described and wood is under-valorized. Especially very few is known about small diameter trees although they may be used, directly as round wood, in construction timber building. A selection of abundant species was done and characterization tests were performed to assess their usability as building material. The aim of this work was t...
M Leroy, K Candelier, J Damay, J Bossu, R Lehnebach, M-F Thevenon, J Beauchene, B Clair
Field durability testing of wood above ground - Part 1: 15 years’ experience with the Bundle method
2023 - IRG/WP 23-20695
A ‘jack of all trades’ method for above-ground wood durability testing has been sought for decades, but until now no method has found its way into standardization. The method of choice shall be applicable for untreated and treated wood – ideally also for wood composites. It shall be reproducible, objective, fast, easy, and inexpensive. Finally, it shall provide high predictive power.
This s...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Field durability testing of wood above ground - Part 2: The full guideline of the Bundle method
2023 - IRG/WP 23-20696
To determine the biological durability of wood above ground, numerous approaches for test methods have been pursued and tried out in the field in the past. So far, no method has managed to find its way into a European standard. During the last 15 years, experience with the Bundle method has been gained. As described in Part 1 of this paper, the method is recommended as a suitable tool for determin...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Laboratory durability testing of preservative treated wood products – first attempts and observations
2023 - IRG/WP 23-20697
In the past, durability classes (DC) had been assigned to wood species, sometimes also to homogenously modified wood-based materials such as thermally modified wood. More recently, some standards allow for classifying the biological durability of chemically modified wood, preservative treated wood and wood composites. Even treated products may be subject to durability classification, but necessary...
C Brischke, M Sievert, M Schilling, S Bollmus
Accelerated surface mould testing for exterior wood treatment in Temperate, Tropical and Laboratory environments
2023 - IRG/WP 23-20699
Mould attack is a very common cause of discoloration on wooden surfaces and can subsequently promote development of wood decay by other organisms. Prevention of mould growth is relevant for both pigmented wood paints as well as more transparent systems with a high or low amount of binder. The use of commercial biocides has led to effective microbiological inhibition in many contexts, but the incre...
A Nazeri, J Stenbaek, T R Laursen, A H H Wong, B M Hasnul
Improvement of durability of Scots pine against termites by impregnation with citric acid and glycerol followed by in situ polyesterification
2023 - IRG/WP 23-30777
Scots pine (Pinus sylvestris) sapwood samples were impregnated with solution containing citric acid (CA) and glycerol (Gly) followed by heating 140 °C according to already described procedure (L'hostis et al. 2018). The resulting modified woods were then used to evaluate the effect of chemical modification on the durability against termites. Two kinds of experiments were conducted for this purpos...
M Mubarok, J Damay, E Masson, E Fredon, Y S Hadi, I W Darmawan, P Gerardin
Suitability of boron preservative treatment of minor species as framing in New Zealand buildings
2023 - IRG/WP 23-30778
The inclusion of alternative species to radiata pine, predominantly exotic species, in the building code (NZS 3602) raises questions as to whether they require preservative treatment and, if so, whether they can be adequately treated using current industry processes.
Early research with boron indicated that the dip/diffusion method for green timber would give adequate preservative retention in sa...
D Page, I Simpson, T Singh
Establishing the minimum effective penetration of wood preservatives in the refractory heartwood of E. nitens
2023 - IRG/WP 23-30780
Conventional pressure treatment of many Australian hardwoods results in little to no penetration of heartwood and a non-uniform envelope treatment of <5 mm surrounding a mostly untreated core. This is a major issue for many of the low durability plantation hardwood timbers that are grown in Tasmania, which contain high percentages of heartwood. Long term studies on softwoods such as spruce decking...
J R Vargas, J J Morrell, L Yermán, K C Wood
Influence of weathering of wood surfaces before and after treatment with iron(II) sulphate
2023 - IRG/WP 23-30786
Outdoor wood is exposed to various factors that cause the wood to grey or age. The ageing processes can vary greatly depending on the exposure. Parts of the wood that are not exposed to external factors, e.g. under the eaves, are less exposed and the ageing process is therefore slower. This can be accelerated by solutions based on iron ions. In this way, the wood greys quickly and evenly. However,...
B Lesar, M Humar, F Osvald
A novel wood preservative with vegetal extracts-cypermethrin mixture protects H2-weathered envelope-treated tropical hardwood kempas against Coptotermes termites
2023 - IRG/WP 23-30794
In accordance with sustainability development initiatives by commercial wood protection to conceive of cost-effective, environmentally acceptable wood treatment solutions replacing traditional biocides, this paper reports an aboveground subterranean termite test of termite-susceptible heartwood blocks of the tropical (Malaysian) structural hardwood kempas (Koompassia malaccensis) envelope-treated ...
D Messaoudi, A H H Wong
Envelope wood protection against subterranean termites under H2-hazard class tropical environment by a new generation wood preservative with vegetal extracts-cypermethrin mixtures
2023 - IRG/WP 23-30795
Wood protection industries in progressive economies globally are compelled to develop cost-effective, environmentally acceptable wood treatment solutions for long term carbon storage in wood materials/products while appealing to consumer demands for low environmental impact treated wood. A new generation wood preservative, based in part on 2% vegetal extracts and 0.16% cypermethrin components, has...
D Messaoudi, A H H Wong
Biological durability and wood-water interactions of sorbitol and citric acid modified wood – Effects on the expected service life
2023 - IRG/WP 23-40960
A high level of research activities on sorbitol and citric acid (SorCA) modified wood has been recognized in Europe over the last few years. As this treatment is close to entering an industrial-scale production, it is of interest to investigate how such treated wood performs upon long-term outdoor exposure. Hence, in this study Scots pine (Pinus sylvestris L.) sapwood was modified with aqueous sol...
K Kurkowiak, L Emmerich, H Militz
The influence of chemical and thermal modification on homogeneity between sapwood, heartwood, and transition wood of short rotation teak
2023 - IRG/WP 23-40961
Short rotation teak wood has low quality especially in durability. Heartwood presents sufficient natural durability and poor impregnability; meanwhile, most sapwood requires special treatment to increase its durability. The objective of this work was to investigate the effect of thermal or chemical treatment on homogenization between sapwood, heartwood, and transition wood for some selected proper...
R Martha, B George, W Darmawan, P Gerardin
Field test methods as long-term aging – report of selective wood properties
2023 - IRG/WP 23-40962
Wood samples from a long-term field test are a valuable compendium of information about the material in the context of its aging processes. In the current work, wood samples from the round-robin test within the ECOMOD project were used as a material for the natural aging process (III and IV class of utility). The research scope was to determine selected properties of this wood which can be partial...
W Perdoch, M Benc, B Mazela, A Szulc, J Cegiela
Evaluation of the efficacy of silver nanoparticles and chitosan oligomer composites as poplar wood protective treatments against termites
2023 - IRG/WP 23-40963
Populus × euramericana ‘I-214’ (poplar) is a fast-growing species widely distributed throughout the world, and in the Castile-Leon region of Spain it accounts for more than 50% of all plantations. Its wood is becoming increasingly appreciated, yet its low durability against xylophagous agents —termites being one of the most aggressive and destructive in warm climates— continues to be a li...
E Spavento, M T Troya, M Casado-Sanz, J Martín-Gil, P Matín-Ramos, L Robertson, L Acuña-Rello
Effect of impregnation modification treatment on properties of Paraserianthes falcataria wood
2023 - IRG/WP 23-40966
Modification treatment can improve the properties of wood, particularly those of fast-growing species. Paraserianthes falcataria, also known as batai, is a fast-growing species with low wood density. This species has piqued the interest of those involved in industrial wood processing as a promising alternative for construction. The aim of this study is to improve the dimensional stability of batai...
A S Yusoh, A S Boneka, M K Anwar U, S Salim, S H Lee