Your search resulted in 3042 documents. Displaying 25 entries per page.
Effect of a wood stabilizer on checking of red oak log sections
2015 - IRG/WP 15-30664
Abstract: Reduced check development and dimensional stability can be important attributes in wood products used for decorative applications. The potential for using a silane-based stabilizer product to reduce checking was assessed on red oak stem and log sections. Pressure treatment produced the largest uptakes, although the levels suggested that the solution had failed to completely penetrate th...
C S Love, J J Morrell
Functional silicones used as a potential tool for the development of non-biocidal wood treatments
2015 - IRG/WP 15-30665
The increase of wood resistance against biological agents for outdoor use is conventionally performed by deep impregnation with preservatives. However, some of the traditional wood preservatives, used for decades for wood protection and regarded as the most effective, are currently subjected to severe restrictions because of their toxicity. In fact, new preservation technologies are constantly ent...
F Lhumeau, C Delaite, F Marchal, F Pochon, M Kutnik
Potential of teak heartwood extractives as a natural preservative against Nasutitermes corniger termite
2015 - IRG/WP 15-30666
Most low durability timber are treated with waterborne preservatives consisting of metallic salts, however, these substances make the process expensive and are harmful to man and the environment, requiring cares with handling, dosing and leaks. Due to these facts, several researches have shown the use of natural substances, extracted from the wood of various naturally durable species, as potential...
V Fassina Brocco, J Benigno Paes, L Gonçalves da Costa, S Brazolin
The effect of preservative treatment on mechanical strength and structural integrity of wood
2015 - IRG/WP 15-30667
The use of wood for demanding construction applications is increasing in Europe. Wooden constructions are frequently designed of susceptible conifer wood, which is endangered by wood decay fungi in wet applications. Therefore in many cases treating wood with preservatives is unavoidable to ensure the desired service life. However, chemical treatment of wood can result in changes of its mechanical ...
M Humar, D Kržišnik, C Brischke
Performance of kiln-dried and air-dried anti-sapstain treated pallet timber under use scenarios against wood discolouring fungi
2015 - IRG/WP 30669
During their lifespan there is a high probability that wooden pallets and packaging material will be exposed to rainfall or rewetting conditions, increasing the risk of growth of discolouring fungi. Kiln-drying of wooden pallets and packaging material without anti-sapstain treatment does not give efficient protection against wood discolouring fungi during rewetting periods. However additional temp...
A Steitz, E Stoyanova, N Pfabigan, R Gründlinger
Durability of Fence Posts of Four Wood Species After 20 Years in Field Test
2015 - IRG/WP 15-30670
In the past years, wood consumption from native forests has drastically reduced the availability of wood. Fast-growing species such as Pinus and Eucalyptus suitably impregnated with chemicals may show a service life equal or higher than hardwood with high natural durability. The field tests have been an alternative widely used to evaluate the durability of wood and the efficiency of preservatives....
A Florian da Costa, A C Salgado de Freitas, E Meneses Oliveira
Mould growth on spruce claddings and the effect of selected influencing factors after 4 years of outdoor testing
2015 - IRG/WP 15-30671
Norway spruce (Picea abies) is the most frequently chosen wood species as claddings in façades in Norway, and is used both coated and uncoated. The visual changes that occur during weathering can be colour changes, abrasion or wear, blistering, flaking, and even cracks in the wood or coating, but more often growth of mould and blue stain fungi is the main challenge. A field test with synchronous monitoring of relative humidity, air temperature, material temperature and wood moisture content in Norway spruce claddings has been performed in southern Norway as part of the ClimateLife project. Visual evaluation of blue stain and mould growth according to EN 927-3 was performed, and evaluation data after 46 months exposure is presented. The objectives were to study the effect of 1) environment, 2) cardinal direction and 3) colour of the coated surface on growth of blue stain and mould fungi and to study the variation in relative humidity, air temperature, wood moisture content and material temperature. After 46 months exposure, the red coating system had generally the lowest mould ratings and the uncoated claddings had the highest. Of the white coloured claddings the ones facing south had lower mould ratings than those facing north, but the opposite were found for red coloured claddings. The relative humidity was higher in front of claddings exposed northwards and in a shaded environment compared to an open environment against south. In an open environment red coloured claddings had the lowest wood moisture content and highest material temperature, and red coloured claddings against south had the highest maximum material temperature.
L Ross Gobakken, G I Vestøl
Search for an anti-sapstain treatment for fresh radiata pine wood in compliance with European BPD norms: Field Tests
2015 - IRG/WP 15-30673
In response to the impending restrictions on the use of pesticide active ingredients developed to control the staining of fresh wood, as a result of regulation issued in 2009 by the European Union, a project was proposed to test an alternative anti-sapstain treatment that meets both the European restrictions and the performance required for an export-quality radiata pine fresh wood treatment. A se...
P Montes C, T Hanke W
Development of a new characterization method to analyse Cypermethrin penetration in wood material by immunolabelling
2015 - IRG/WP 15-30674
The preservative efficacy of organic biocides is strongly related to their capacity of penetration and retention within wood tissues. The specific detection of the pyrethroid insecticide cypermethrin is currently obtained after extraction followed by chemical analysis by chromatography techniques. However visualizing the insecticide molecule within the wood structure requires specific probes toget...
S Tapin-Lingua, K Ruel, J-P Joseleau, D Messaoudi, O Fahy, M Jequel, M Petit-Conil
The situation of the industrial protection of wood in Argentina (La situación de la protección industrial de la madera en Argentina)
2015 - IRG/WP 15-30675
Argentina holds 33 million hectares of native forests and 1.2 million hectares of cultivated forests, which make it the 3rd Latin American country with the largest surface of cultivated forests of the region. (Ministry of Industry, 2012). The industrial impregnation of wood through vacuum pressure was first implemented in our country in the year 1932, and currently there are over 100 active plants...
D A Gherscovic
Antifungal properties of wood treated with IPBC and organosilicone compounds against Coniophora puteana
2015 - IRG/WP 15-30676
The aim of the research was to increase durability of Scots pine wood treated with 3-Iodo-2-propynyl butylcarbamate (IPBC) through organosilicon compounds. The IPBC was combined with organosilicon compounds (alkylsilane and alkylsilane with amino groups) for supporting its antifungal properties. The mycological examination against Coniophora puteana was performed to determine the resistance of woo...
W Perdoch, B Mazela, A Waśkiewicz
Bio-friendly preservative systems for enhanced wood durability - the first periodic report on DURAWOOD
2015 - IRG/WP 15-30677
The objective of the paper is the DURAWOOD scientific project carried out within Polish-Norwegian Research Programme, which lasts from September 2013 till August 2016. The aim of the project concentrates on the developing of a new, eco-friendly and biocide-free wood protective systems as an alternative to traditional, commonly used preservatives or coatings, containing biocides. Several wood prese...
B Mazela, M Broda, W Perdoch, L Ross Gobakken, I Ratajczak, G Cofta, W Grześkowiak, A Komasa, A Przybył
Indentation and pendulum hardness tests: two convenient assessment methods of the performance of exterior wood coatings
2015 - IRG/WP 15-40689
Developing formulations of exterior wood coatings with long service life is a big challenge. For many years in Europe the performances have been mainly evaluated through weathering tests (within the EN 927 series) followed by visual assessment (blistering, flaking, mould growth, chalking and cracking), colour and gloss measurements, and adhesion tests. Very recently the importance of the mechanica...
L Malassenet, L Podgorski, M Truskaller, G Grüll
A review of the analytical methods used in determining the decay resistance of heat treated wood
2015 - IRG/WP 15-40690
Heat treatment as a wood process is increasingly used because of its non-biocide behaviour and its low environmental impact. This sort of treatment is based on biopolymer chemical degradation by heat transfer. This process improves mainly the dimensional stability and the decay resistance of wood.
Wood becomes darker after this type of treatment and thus gives it an aesthetic appearance. These i...
K Candelier, M-F Thévenon, A Pétrissans, S Dumarçay, P Gérardin, M Pétrissans
Remedial treatment of difficult to access timber in buildings
2015 - IRG/WP 15-40691
The quest to understand remedial treatment for timber framing begun following the ‘leaky building crisis’ in New Zealand which came to prominence in 2000. Several in-situ remedial treatment products are used in New Zealand. However, effectiveness of these treatments is still unclear particularly in situations where not all faces of the timber can be assessed. This research was conducted to det...
T Singh, I Simpson, D Page
Effect of natural variability of European Oak wood on heat treatment process and potential implication on wood durability
2015 - IRG/WP 15-40693
Environmental pressures appeared in France and in most European countries during the last decade has led to the development of more environmentally acceptable preservation methods. In this context, wood heat treatment has been one of the most investigated alternative method during the last years. Treated at temperatures ranging between 180 and 220°C, wood components undergo more or less important...
J Hamada, A Pétrissans, F Mothe, M Pétrissans, P Gérardin
Depictions on Wood: Acceptation and Internalization of Wood, which is an intercultural interaction tool, as “A Valuable Object” (Wood is Good)
2015 - IRG/WP 15-40694
These sample descriptions have been made for the course named “Importance of Wood in Intercultural Interaction”, a new elective course for all undergraduate students of Hacettepe University, within the framework of the curriculum of Wood Products Industrial Engineering, which has been updated within the scope of Bologna Process. With this course, designed by a woodlover viewpoint for the first...
I Usta
Characterization of biofilm formation on wood treated with vegetable oils by color-based image interpretation method
2015 - IRG/WP 15-40697
The protection of wood in order to extend its service life is an important issue nowadays. As an alternative to traditional wood coatings biofilms can be used. It is a living protective coating for the wood surface against UV and bio-degradation that has the ability to recover from local damage, such as cracks. This paper presents preliminary results of biofilm formation from an 8-month’s fie...
K Filippovych, H Huinink, L van der Ven, O C G Adan
Application of nanoparticles of silver and nanoparticles of titanium dioxide in reinforcement of wood and coating for wood in Costa Rica
2015 - IRG/WP 15-40698
Wood is one of the most widely used materials in last 20 years by society in many applications, with a considerable proportion of this material coming from forest plantations. Plantations usually produce timber with reduced strength properties and low natural durability. On the other hand, nanotechnology applications have the potential to increase wood properties. Likewise, nanotechnology cannot o...
A Berrocal Jiménez, R Moya Roque, A Lucrecia Rodríguez, J R Vega Baudrit
How does the test methodology influence the outcome of durability testing of thermally modified wood
2015 - IRG/WP 15-40699
Thermally modified wood is commercially available on the European market since many years. Today, many production units with various production capacities and different modification processes exist. Industrial scale wood heat treatment processes, under the trade name of ThermoWood were developed in Finland. ThermoWood has two standard treatment classes with different target properties, namely Ther...
A Gellerich, S Bollmus, H Militz
How to Increase the Lifespan of Exterior Wood Coatings
2015 - IRG/WP 15-40700
In addition to aesthetic appeal, coatings are designed to protect the wood from weathering degradation in outdoor conditions. This paper gives an overview of the effects of main components of coating, coating properties, and wood treatments on coating performance. Understanding how different type of resins (alkyd, acrylic or polyurethane), amount of pigments, type of solvents (organic or water), a...
M Nejad
A novel enzymatic treatment as a new approach for wood protection
2015 - IRG/WP 15-40701
Wood durability is a worldwide concern and most treatments tend to fail with regard to their efficacy along the time. Weather conditions lead to a loss of the treatment substances into the surrounding environment and, in consequence, generate also a public health concern.
Recently, the employment of oxidative enzymes, such as laccases, has been proposed as a tool for lignocellulosics modificatio...
C Fernández-Costas, S Palanti, M Ángeles Sanromán, D Moldes
Investigation of Dimensional Stability and Coating Performance of Different Heat-Treated Poplar Wood Before and After Accelerated Aging
2015 - IRG/WP 15-40702
In this investigation, coating performance of heat-treated poplar wood (Populus tremuloioes) in different environments, before and after accelerated aging was studied. Specimens with 150×100×20 mm and 20×20×20 mm in dimensions were prepared. Heat treatments were performed in air, steam and linseed oil media. Specimens were coated by alkyd based stain. Adhesion strength before and after aging, ...
A Talaei, D Ansari Movahed, G Rassam
Termite and insect resistance of acetylated wood
2015 - IRG/WP 15-40703
The benefits from acetylation of wood to enhance resistance against fungal decay and dimensional stability have been known for many years. Since 2007 Accsys Technologies has been commercially producing Accoya® wood that is based on acetylation of radiata pine. A number of studies on the resistance of acetylated wood to attack by wood destroying termites have been conducted, but there is no common...
F Bongers, M Kutnik, I Paulmier, J Alexander, H Militz
Durability of reaction to fire performance of FRT wood products in different end use applications – Methods and results
2015 - IRG/WP 15-40705
Fire retardant treatments (FRT) may considerably improve the reaction to fire properties of wood-based products and the highest fire classifications for combustible products can be reached, but the maintained reaction to fire performance e. g. in exterior applications needs to be addressed in order to form a basis for new and reliable wood products with improved fire performance.
A European Techn...
B Östman, L Tsantaridis