Your search resulted in 1507 documents. Displaying 25 entries per page.
Assessment of the effects of rentex remedial treatment on some wood pole inhabitant micro-organisms
1994 - IRG/WP 94-30053
The effects of a remedial ground-line treatment using Rentex, a stabilised paste containing a mixture of fluoride and dichromate salts, on the micro-organisms inhabiting a sample of some 160 creosoted, on-line, electricity distribution poles, have been investigated as part of an appraisal of the efficacy of this remedial treatment. Half of the poles were treated and the other half used as controls...
D C R Sinclair, G M Smith, A Bruce, H J Staines
Experiences with supervision schemes for treated timber in Denmark
1984 - IRG/WP 3315
Since 1967 a voluntary supervision scheme for vacuum-pressure treatment was established in Denmark. In 1976 the Nordic Wood Preservation Council - NWPC - established a scheme based on wood preservation classes for treated timber as a joint technical standard valid in Denmark, Finland, Norway and Sweden. This paper deals with inspection results over 17 years for CCA treatment within our organizatio...
J Sabroe
Biological and physical properties of phenolic-resin treated wood before and after natural weathering
1999 - IRG/WP 99-40132
Biological and physical properties of phenolic resin-treated particleboards, which were made from fast growing tress and agrowaste as raw materials, were evaluated before and after natural weathering in tropical climate. The particles were sprayed with a mixture of a low molecular weight phenol-formaldehyde resin (5.0, 7.5 and 10% loading) and the adhesive phenol resin (8% loading). Results with l...
S Yusuf, Y Sudiyani, H Kajita, Y Imamura, M Takahashi
A report of the Technical Recommendations documents for the Canadian Wood Protection and Preservation Facilities and an environmental study of storm water runoff from anti-sapstain treatment plants
1988 - IRG/WP 3478
With the completion of the Final draft of the Technical Recommendations (TR) documents for the Wood Preservation and Wood Protection Industry, there are naturally questions on what is expected from these documents and how Environment Canada and Provincial regulatory agencies may interact with the wood preservation industry. In general, it is expected that the Canadian Wood Preservation and Protect...
G Das, V N P Mathur
Kerfing and center-boring reduce checking in CCA-treated slash pine posts
1997 - IRG/WP 97-40082
Single and double kerfing, center-boring and incising were applied to green, peeled, slash pine posts. Posts were air dried for ten weeks and assessed for the number of surface drying checks greater than 1.0 mm in width. Posts were then pressure treated with a chromated-copper-arsenate (CCA-C) preservative and exposed outdoors in a horizontal position. The number of surface weathering checks in th...
P D Evans, R Wingate-Hill, R B Cunningham
Migration of chlorothalonil and carbendazim in fruits stored in wood treated with the anti-sapstain formulation Tuff Brite C
1997 - IRG/WP 97-50097
Fruits and vegetables stored in treated wood boxes are in contact with the products used for the treatment. In order to obtain regulatory approval for incidental food contact it is necessary to determine the quantity of residues on these fruits or vegetables. When the active materials are used in agriculture it is required that residues found are below to the MRL fixed for these substances. In the...
J F Cooper, D Riboul, M De Vleeschauwer, T L Woods
Preservative treatment of green timber by soaking in ammoniacal copper borate
1984 - IRG/WP 3292
Freshly sawn boards of radiata pine sapwood were preservative treated by soaking in ammoniacal copper borate. Optimum schedules were obtained by partially seasoning the boards for one week prior to treatment. This aided the absorption of preservative and reduced the required soaking time to approximately 2 hours. Complete boron penetration was obtained after one week of block storage under cover a...
P Vinden, A J McQuire
Development of software to automate the quantification of checking occurring in preservative treated wood exposed to weathering
2001 - IRG/WP 01-20228
Surface checking often disfigures the appearance of wood treated with water-borne preservatives and treatments designed to reduce such checking have been receiving increasing attention. Progress in this area has however been slowed by the lack of a method of rapidly and accurately quantifying checking at treated wood surfaces. A software package has therefore been developed which identifies, measu...
A G Christy, P D Evans
Microdistribution of Copper in Copper-Ethanolamine (Cu-EA) Treated Southern Yellow Pine (Pinus spp.) related to density distribution
2004 - IRG/WP 04-40270
The relationship between copper absorption and density distribution in wood cell walls was investigated in this study. The density distribution on layer level was obtained from two approaches: (1) calculation by using data obtained from literature; (2) microdistribution of carbon and oxygen atoms in the wood cell. The microdistribution of carbon and oxygen in untreated southern yellow pine (Pinus ...
Jinzhen Cao, D P Kamdem, E Pasek
Study of modulus of rupture, circumference taper, sapwood thickness and CCA treatment of Norwegian origin Pinus sylvestris poles
1994 - IRG/WP 94-20054
Nondestructive strength testing with Pilodyn (6J) of Norwegian Pinus sylvestris poles revealed effective modulus of rupture (MOR) of 54.39 N/mm² at wet conditions after CCA-C treatment and circumference measurement revealed circumference taper of 0.021 m/n. Sapwood thickness or penetration of CCA-C study revealed that 77% poles were with sapwood thickness equivalent to 39.6% of radius of poles an...
A K Lahiry, S Begum, G N M Ilias, M A B Fakir, R U Hafiz
Environmental aspects of wood preservation
1987 - IRG/WP 3406
The preservation industry employs a wide range of chemicals and processes to provide timber commodities capable of resisting biodeterioration and degradation. The public often perceives the chemicals as health hazards and treatment plants as potential threats to the environment. This paper attempts to place in proper perspective the value of wood preservation. It discusses aspects of health and sa...
H Greaves
Evaluation of impact of CCA-treated wood on the marine environment
1995 - IRG/WP 95-50040-15
This paper reviews the literature relating to the potential of CCA-treated wood to affect the marine environment and outlines the compounds required for a model which could be used to predict the environemental impact of maritime construction using such timber. Marine pilings require high loadings of CCA to provide protection from marine borers. Though loadings of 32-48 kg/m³ provide long-term pr...
R M Albuquerque, S M Cragg
Effect of treatment process on performance of copper-chrome-arsenate. Part 1: Fungus cellar tests
1995 - IRG/WP 95-40045
Pinus radiata sapwood stakes 20 x 20 x 400 mm³ were treated with CCA Type C using a range of concentrations and three treatment processes; Bethell, Lowry and Rueping. Preservative retention was determined by chemical analysis of treated material. Following fixation, fungus cellar stakelets, 5 x 10 x 180 mm³ were cut from treated material and after leaching were exposed in unsterile soil beds in ...
M E Hedley, J Anderson, J B Foster, B E Patterson
Evaluation of fluid distribution in pressure treated wood in different flow directions
2004 - IRG/WP 04-40281
Among different methods, polymerization technique was chosen to study distribution of fluid through cell types in treated wood. Red maple wood specimens with the size of 2 by 2 by 4 cm (radial, tangential and longitudinal, respectively) were prepared. Styrene monomer was used as the fluid for impregnation; because its physical properties such as surface tension, specific gravity and viscosity fall...
A Omidvar, M H Schneider
The Disposal of CCA-Treated Wood in Simulated Landfills: Potential Impacts
2003 - IRG/WP 03-50198
Landfills are typically where CCA-treated wood is currently disposed, and will likely continue to be the primary form of management in the future. It has been shown that arsenic, copper and chromium leach from CCA-treated wood in certain situations; however, the impact of the disposal of CCA-treated wood on landfill leachate is currently unknown. The objective of this research is to examine the po...
J Jambeck, T G Townsend, H M Solo-Gabriele
A method test of chemicals for the treatment of walls infected with Serpula lacrymans
1992 - IRG/WP 92-2408
A method, which has been used in the UK for over 25 years, is described for assessing the effectiveness of products for application to walls during remedial treatment to eradicate the dry rot fungus Serpula lacrymans. Approvals for products previously used for this purpose in the UK are being changed. Approval for tri n-butyltin oxide has been withdrawn, and PCP derivatives can continue to be used...
J K Carey
Occupational exposure risk assessment at a commercial treatment plant using copper azole preservative
1998 - IRG/WP 98-50101-15
Experience with traditional water-based preservatives such as chromated copper arsenate (CCA) applied in closed system vacuum pressure impregnation plants has shown that operator atmospheric exposure is low during normal operation.
TANALITH E is a commercially available copper azole wood preservative introduced as a chrome and arsenic-free alternative to CCA based on the actives copper, tebuconaz...
A S Hughes, M Connell
Comparison of the anti-fungal efficacy of Cobra with drill perforation on oscillating pressure treated spruce transmission poles -Laboratory test
1988 - IRG/WP 3469
A laboratory method for measuring the depth of penetration of the fungicidal concentrations effective against basidiomycetes (brown rot) was developed. The tests on CCB oscillating pressure treated spruce transmission poles have shown that the depth of salt penetration can be increased by about 10 mm by a drill perforation before the impregnation. An even better penetration is reached, however, if...
E Graf, B Zgraggen
Comparison of thermally modified wood originating from four industrial scale processes – durability
2002 - IRG/WP 02-40229
This study examined the differences in biological wood properties of heat treated wood originating from four different European industrial heat treatment plants. The manufacturers of heat treated material were: PLATO Hout B.V./Netherlands, Thermo Wood/Finland, New Option Wood/France and Menz Holz/Germany where Oil-Heat treated Wood (OHT) is produced.
The results of miniblock tests with basidiomyc...
C R Welzbacher, A O Rapp
Management strategies for the disposal of CCA-treated wood
2000 - IRG/WP 00-50155
A two-fold management strategy is presented for the disposal of wood treated with chromated copper arsenate (CCA). The first part focuses on the use of alternative wood treatment preservatives. The second part of the management strategy addresses short-term disposal issues (less than 25 years) by developing new methods to handle the waste. A set of seven alternative wood preservatives were evaluat...
H M Solo-Gabriele, T G Townsend
Reappraisal of some fungicides by the amended JWPA method
1992 - IRG/WP 92-3689
Organoiodine compounds which have been commercialized these years in Japan poorly performed as fungicides in the amended JWPA decay test (Standard 1, 1989) when applied to superficial treatment of timber. Because some parts of active ingredients seemed to disappear from the treated timber surface mainly due to the severe leaching cycles. This was prominently true for beech (Fagus crenata Blume) sa...
K Tsunoda
The effect of heat treatment on the properties of spruce
1994 - IRG/WP 94-40032
The effect of high temperature treatment (above 150°C) on the wood quality is studied at the VTT. Improved dimensional stability, lower equilibrium moisture content and increased durability against biodeterioration is achieved, depending on the environmental factors. The biodeterioration resistance of spruce is improved due to changes in chemical composition and lower equilibrium moisture content...
H Viitanen, S Jämsä, L Paajanen, A J Nurmi, P Viitaniemi
Kiln drying of LSOP treated timber: rate of solvent evaporation, overpaintability and recovery of the solvent
1992 - IRG/WP 92-3711
The rate of solvent evaporation from LOSP treated timber dried in a kiln at 35°C has been investigated. Around 50% solvent removal has been found to be consistent with good overpaintability using a water based acrylic primer. It has been demonstrated that an activated carbon solvent recovery system is capable of removing all the solvent vapour from the outlet of a commercial joinery drying kiIn, ...
P Warburton, L B Sheard
Field fencepost tests of several species treated with water-borne preservatives by rural methods
1986 - IRG/WP 3385 E
Fencepost field results in ground-contact treated by rural methods: immersion-diffusion and sap displacement by evaporation are analyzed. Copper-chrome-arsenic and copper-fluor-chrome preservatives were used in two concentrations. The wooden species studied were: Pinus pinaster, Eucalyptus globulus and Quercus rubra. For each of the test units decay index evolution was analyzed after five years ex...
M V Baonza Merino
Occurrence and importance of various types of fungal and bacterial decay in CCA-treated horticultural pine posts in New Zealand
1984 - IRG/WP 1234
A detailed microscopical examination has been carried out on samples taken from CCA-treated pine posts exposed in horticultural soils. The following decay types were observed: white rot, brown rot, soft rot, tunnelling bacteria, cavitation bacteria, and bacterial erosion. The occurrence and importance of the various decay types between different regions, and plots within a specific region, varied ...
T Nilsson