Your search resulted in 1000 documents. Displaying 25 entries per page.
Effect of Moisture Cycles and Timber Treatment on the Performance of Screwed Connections
2023 - IRG/WP 23-20694
The impact of moisture in timber structures is associated with the deterioration of timber, and loss of mechanical performance. Methods have been developed to treat timber using chemicals to inhibit deterioration, however, water intrusion has much more immediate effects on the mechanical properties of timber associated with swelling and shrinkage of the wood. The effects of moisture on the mechani...
L Yermán, M Xiao, Z Yan, L-M Ottenhaus
Field durability testing of wood above ground - Part 1: 15 years’ experience with the Bundle method
2023 - IRG/WP 23-20695
A ‘jack of all trades’ method for above-ground wood durability testing has been sought for decades, but until now no method has found its way into standardization. The method of choice shall be applicable for untreated and treated wood – ideally also for wood composites. It shall be reproducible, objective, fast, easy, and inexpensive. Finally, it shall provide high predictive power.
This s...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Field durability testing of wood above ground - Part 2: The full guideline of the Bundle method
2023 - IRG/WP 23-20696
To determine the biological durability of wood above ground, numerous approaches for test methods have been pursued and tried out in the field in the past. So far, no method has managed to find its way into a European standard. During the last 15 years, experience with the Bundle method has been gained. As described in Part 1 of this paper, the method is recommended as a suitable tool for determin...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Laboratory durability testing of preservative treated wood products – first attempts and observations
2023 - IRG/WP 23-20697
In the past, durability classes (DC) had been assigned to wood species, sometimes also to homogenously modified wood-based materials such as thermally modified wood. More recently, some standards allow for classifying the biological durability of chemically modified wood, preservative treated wood and wood composites. Even treated products may be subject to durability classification, but necessary...
C Brischke, M Sievert, M Schilling, S Bollmus
Improvement of durability of Scots pine against termites by impregnation with citric acid and glycerol followed by in situ polyesterification
2023 - IRG/WP 23-30777
Scots pine (Pinus sylvestris) sapwood samples were impregnated with solution containing citric acid (CA) and glycerol (Gly) followed by heating 140 °C according to already described procedure (L'hostis et al. 2018). The resulting modified woods were then used to evaluate the effect of chemical modification on the durability against termites. Two kinds of experiments were conducted for this purpos...
M Mubarok, J Damay, E Masson, E Fredon, Y S Hadi, I W Darmawan, P Gerardin
Suitability of boron preservative treatment of minor species as framing in New Zealand buildings
2023 - IRG/WP 23-30778
The inclusion of alternative species to radiata pine, predominantly exotic species, in the building code (NZS 3602) raises questions as to whether they require preservative treatment and, if so, whether they can be adequately treated using current industry processes.
Early research with boron indicated that the dip/diffusion method for green timber would give adequate preservative retention in sa...
D Page, I Simpson, T Singh
Establishing the minimum effective penetration of wood preservatives in the refractory heartwood of E. nitens
2023 - IRG/WP 23-30780
Conventional pressure treatment of many Australian hardwoods results in little to no penetration of heartwood and a non-uniform envelope treatment of <5 mm surrounding a mostly untreated core. This is a major issue for many of the low durability plantation hardwood timbers that are grown in Tasmania, which contain high percentages of heartwood. Long term studies on softwoods such as spruce decking...
J R Vargas, J J Morrell, L Yermán, K C Wood
Performance of treated Malaysian semantang bamboo (Gigantochloa scortechinii) - field and laboratory durability evaluation
2023 - IRG/WP 23-30788
Field performance of sematan bamboo, Gigantochloa scortechinii was evaluated under the Malaysian tropical climate, along with laboratory evaluation to white-rot fungi and mold. Starch was removed from the bamboo by submerging the bamboo in the river for 6-8 weeks, kiln-dried and cut to 300 mm (L) round bamboo and 25 mm (W) x 50 mm (L) stripe for the field and laboratory test respectively. Bamboo w...
S Lipeh, T Khadiran, Z Jalaludin, M K Anwar U
Identifying compatible waterborne timber preservatives and fire retardants for use in a VPI system: a practical approach
2023 - IRG/WP 23-30796
To enhance the use and suitability of timber in all applications in both exterior and interior settings, timber typically needs to be treated with a preservative and/or a fire retardant chemical. Combining fire retardants with preservatives into a single treatment process has been a long-term aim of researchers in the timber preservative industry because of the significant logistic and economic ad...
R Robinson, S Meldrum
Outdoor performance of Tanalith® K treated timber: Dimensional stability and corrosivity towards metal fasteners
2023 - IRG/WP 23-30798
This study was carried out to investigate dimensional stability and corrosivity towards metal fasteners in radiata pine (Pinus radiata D. Don) treated with Tanalith® K to Hazard class 4 (H4) retentions in comparison with chromated copper arsenic (CCA) treated timber. For corrosion test, untreated and treated matched specimens were prepared from Australian-grown radiata pine, tested with mild stee...
G Rassam, J Hague, D Humphrey
Biological durability and wood-water interactions of sorbitol and citric acid modified wood – Effects on the expected service life
2023 - IRG/WP 23-40960
A high level of research activities on sorbitol and citric acid (SorCA) modified wood has been recognized in Europe over the last few years. As this treatment is close to entering an industrial-scale production, it is of interest to investigate how such treated wood performs upon long-term outdoor exposure. Hence, in this study Scots pine (Pinus sylvestris L.) sapwood was modified with aqueous sol...
K Kurkowiak, L Emmerich, H Militz
The influence of chemical and thermal modification on homogeneity between sapwood, heartwood, and transition wood of short rotation teak
2023 - IRG/WP 23-40961
Short rotation teak wood has low quality especially in durability. Heartwood presents sufficient natural durability and poor impregnability; meanwhile, most sapwood requires special treatment to increase its durability. The objective of this work was to investigate the effect of thermal or chemical treatment on homogenization between sapwood, heartwood, and transition wood for some selected proper...
R Martha, B George, W Darmawan, P Gerardin
Evaluation of the efficacy of silver nanoparticles and chitosan oligomer composites as poplar wood protective treatments against termites
2023 - IRG/WP 23-40963
Populus × euramericana ‘I-214’ (poplar) is a fast-growing species widely distributed throughout the world, and in the Castile-Leon region of Spain it accounts for more than 50% of all plantations. Its wood is becoming increasingly appreciated, yet its low durability against xylophagous agents —termites being one of the most aggressive and destructive in warm climates— continues to be a li...
E Spavento, M T Troya, M Casado-Sanz, J Martín-Gil, P Matín-Ramos, L Robertson, L Acuña-Rello
Impacts of elevated moisture levels and subsequent drying on screwed
2023 - IRG/WP 23-40970
Mass timber (glue-laminated timber, cross laminated timber (CLT) and laminated veneer lumber) are increasingly used in mid-to high rise structures in Australia where the climate is mainly sub-tropical with elevated moisture levels and high termite risk. Moisture intrusion poses a major challenge anywhere but becomes more critical under these conditions. Untreated/non-durable materials are consider...
C M T Roder, C D Gerber, J J Morrell
Through-boring to improve the performance of low durability Eucalyptus species for utility poles: 10-year field test results of pole stubs exposed in Southeast Queensland
2023 - IRG/WP 23-40972
An impending shortage of naturally durable hardwood electricity pole timbers in Australia has encouraged investigation of alternatives containing less durable, untreatable heartwood. Through-boring or drilling holes perpendicular to the long axis before treatment, has been used successfully on refractory softwood poles in North America and might have application in Australia. The use of through-bo...
J Norton, L P Francis, J J Morrell
New wood-modification process based on grafted urethane groups: Durability of carbamamylated Scots pine (Pinus sylvestris L.) wood
2023 - IRG/WP 23-40974
Substituting commonly used toxic preservatives with wood modification treatments can make the wood material less prone to water and moisture uptake. This approach favours a more sustainable protection of wood against biodegradation. In this study, Scots pine sapwood was full-cell impregnated with an aqueous solution of urea (30%), dried at 40°C for 24h, and subsequently heat-treated at 150°C for...
C-F Lin, O Myronycheva, O Karlsson, D Jones, D Sandberg
Properties of thermal modified wood of Pinus pinaster and Pinus radiata from Galicia, Spain
2023 - IRG/WP 23-40985
This article provides the results of a research about the properties of thermal modified wood of maritime pine (Pinus pinaster Ait.), radiata pine (Pinus radiata D.Don) and Scots pine (Pinus sylvestris L.) from Galicia, Spain, thermal treated in the industrial vacuum-heat autoclave plant of FINSA group in Galicia, Spain. These three pine wood species are used in different solid products but due th...
D Lorenzo, J Benito, J Arancón, J Crespo
Modification of wood by fast pyrolysis bio-oil – the NewWave project concept for bio-based wood treatment
2023 - IRG/WP 23-40990
The NewWave project aims to contribute to building a circular economy by introducing sustainable raw materials in different manufacturing lines, replacing toxic chemicals and lowering the environmental footprint of the products. The raw materials are obtained from the thermochemical fractionation of biomass. This process converts biomass residues by fast pyrolysis into Fast Pyrolysis Bio-Oil (FPBO...
A Sandak, J Sandak, F Poohphajai, R Herrera Diaz, A Gubenšek, K Butina Ogorelec, L Kiezebrink, K J Swager, H Heeres, B van de Beld
Optimization of furfurylic alcohol/tannin ratio to improve the performance of biosourced thermoset resins for wood protection
2023 - IRG/WP 23-40994
This study concerns the chemical modification of wood with different ratios of tannin and furfuryl alcohol (FA) in the presence of maleic acid as catalyst. Tannins were used not only as cross-linking agents, but also as co-monomers to improve wood durability, while reducing the amount of FA used. Different aqueous formulations were prepared containing decreasing amount of FA (from 45.45% to 0%) an...
E Azadeh, A Pizzi, P Gérardin, C Gérardin-Charbonnier
Relationships between deterioration part and structural performance in wooden houses
2023 - IRG/WP 23-50376
Based on the survey examples, there are four patterns of deterioration that tend to occur in plywood bearing walls of wooden houses in Japan. The first is a pattern in which wall is in a whole deterioration. It is a no damage wall or test specimen. The second is a pattern in which only the sill is deteriorating. It is caused by moisture or termites from ground to the base. In addition, there is a ...
Y Ota, H Ishiyama, S Okamoto
Improving American Hardwoods Sustainability, Durability and Markets
2023 - IRG/WP 23-50378
The American hardwood industry, which dates back to the first European settlers, has a wealth of experience processing the native hardwoods of North America. The US hardwood resource is mainly located in the eastern United States, from Maine in the North to the Gulf of Mexico in the South and westwards to the Mississippi Valley. The USA has more temperate hardwood species than any other world regi...
D Brooks, M Snow
Towards a microactuator-sensing network for the structural health monitoring of wood
2023 - IRG/WP 23-50380
Timber structures decay over time with degradation in their structural integrity. Changing environmental conditions, varying loads, exposure to moisture or insect attacks lead to changes in their vibrational response behaviour. Here we present a low-cost device used as a triggered exciter to enable the monitoring of the structural integrity of timber bearers or even power poles in electricity netw...
S Oberst, S Sepehrirahnama, C Nerse, Z Brodzeli, J C S Lai, M Mankowski, T Atkinson, R Arango, G Kirker, T Evans
Enhanced durability of bio-based materials for green building
2023 - IRG/WP 23-50382
Wood protection technologies provide tools to enhance the durability of bio-based materials for green building. Both wood and related bio-based material are regarded as eminent for green building. It allows to underpin several of the United Nations sustainable development goals and is regarded critical for the Green Deal objectives of the EU. Nevertheless, to enhance the potential it needs to be b...
J Van Acker, L De Ligne, J Vand den Bulcke
End-of-life options for engineered wood products / Treated timber in a circular economy
2023 - IRG/WP 23-50383
Australians are excellent consumers of products. These products ultimately end up as waste materials and need to go somewhere. Australia produces around 28 million tons of waste per year with around 50% currently ending up in landfill, including a significant amount of timber, engineered wood products (EWP’s), and preservative treated wood (PTW). Limited landfill capacity, increasing costs, and ...
H Brooke
Wood above ground project – Results and future plans
2024 - IRG/WP 24-11041
In 2000, the Danish Technological Institute (DTI) initiated an extensive study to investigate the natural durability of wood. The study involved exposing wood in various orientations to assess its performance. A total of 35 wood material types were exposed at DTI test site in Taastrup, Denmark. Moisture content (MC) was measured through weighing for the initial five years, decay was assessed follo...
A W Christof, R Digaitis, P Fynholm, J Stenbaek, N Morsing, B Lindegaard