Your search resulted in 443 documents. Displaying 25 entries per page.
Formation of hydrophobic wood surface by means of thermal treatment and surface modification with alkyl ketene dimer (AKD)
2016 - IRG/WP 16-40738
One of the major shortcomings of wood-based materials compared to technical materials is attributed to their poor dimensional stability in changing climates and in contact with liquid water. Heat treatment induces chemical change with a consequent decreasing of reactivity of the material showing unwanted surface inactivation. Alkyl ketene dimer (AKD) is a widely used sizing agent in papermaking, w...
T Lovaglio, T Meints, L Todaro, W Gindl-Altmutter
Enhancing wood properties through bio-based and non-biocidal co-polyesters
2016 - IRG/WP 16-40740
The commonly used wood preservation treatments are nowadays facing huge environmental issues, as well as increasing public concern. As regards those concerns, legislation tends to regulate the use of biocidal preservation chemicals.
Thus, it does appear crucial to provide alternatives to the use of biocides to allow different outdoor uses of wood such as for, posts, decking, and cladding or even ...
C L’Hostis, M-F Thévenon, E Fredon, P Gérardin
Durability of Thermally Modified Engineered Wood Products
2016 - IRG/WP 16-40745
In this study, rated plywood, oriented strand board (OSB), laminated strand lumber (LSL), and laminated veneer lumber (LVL) were thermally modified as a post-treatment at 140 °C, 150 °C, 160 °C, 170 °C, and 180 °C using a closed, pressurized treatment method. Eastern larch OSB manufactured from heartwood and sapwood was also thermally modified as a post-treatment at 160 °C and 180°C. All ...
H M Barnes, M D Aro, A Rowlen
The impact of catalyst on the properties of furfurylated beech wood
2016 - IRG/WP 16-40748
European beech (Fagus sylvatica L.) is a major tree species of European forest that is underexploited because of its low dimensional stability and durability. Similarly to what has been developed with radiata pine, furfurylation might be the answer to optimize the utilization of local beech wood. Beech wood furfurylation process was studied using five different catalysts: maleic anhydride, maleic ...
P S Sejati, A Imbert, C Gérardin, S Dumarçay, E Fredon, E Masson, D Nandika, T Priadi, P Gérardin
The effect of acetylation on physical properties of beech (Fagus orientalis) and Alder (Alnus subcordata) wood
2016 - IRG/WP 16-40759
In this study the effect of acetylation on physical properties such as water absorption, volumetric swelling and anti-shrink efficiency (ASE) of beech and alder were investigated. After 24 hours soaking in acetic anhydride, in order to achieving two surface of weight gains, acetylated samples were heated in oven at 120 0C for 90 and 360 minutes. Then water absorption and dimensional stability in...
M Akhtari, M Arefkhani
Improvement of wood properties by impregnation with liquefied spruce bark based resins
2016 - IRG/WP 16-40761
In this paper, biobased phenolic thermosetting resins are designed to be used as wood stabilization treatment. The originality of the study stands in substituting part of phenol by spruce (picea abies) bark: this is achieved by a liquefaction process in phenol in the presence of sulfuric acid as catalyst. Next, thermosetting resins are synthetized from liquefied bark by condensation on formaldehy...
X Duret, E Fredon, E Masson, P Gérardin
Effect of different concentration of furfurylation on physical properties and decay resistance of Paulownia wood
2016 - IRG/WP 16-40762
The furfurylation process is an extensively investigated wood modification process. Penetration of Furfuryl alcohol molecules into the wood cell wall results in a permanent swelling. In the present study, different concentrations effect of furfuryl alcohol monomer on physico-biological properties such as water uptake, dimensional stability and decay resistance of wood polymer made by fast-growing ...
M Ghorbani, H Asghari
Effect of insitu polymerization on practical properties of heat treated wood
2016 - IRG/WP 16-40763
This research was conducted to investigate the effect of combined modification; heat treatment and impregnation with styrene monomer on physical and mechanical properties of poplar wood (Populus deltoides). Test samples were grouped in six levels of control, wood polymer made from styrene, heat treatment at 170 ºC and 200ºC and combined modification; first hat treated at 170 ºC and 200ºC and t...
M Ghorbani, M Mohseni Shaktaei
Estimation of wood degradation determined by visual inspection, mechanical testing and DNA characterisation – report after 3 years of exposure
2016 - IRG/WP 16-30700
The influence of two separate treatments, thermal modification and alkaline copper quaternary (ACQ, Silvanolin©) treatment, on fungal decay, visual disfigurement, deterioration in mechanical properties and fungal community structure was assessed on Norway spruce (Picea abies) and compared with the performance of two naturally more resistant tree species native to North America: Douglas fir (Pseud...
N Thaler, T Martinović, M Bajc, D Finžgar, H Kraigher, A Sinha, J J Morrell, M Humar
Fire retardant treated wood products – Properties and uses
2016 - IRG/WP 16-30701
Wood is combustible, but can still perform very well in fire, especially for load bearing structures. However, visible wood surface may not fulfil the fire requirements in building codes and fire retardant treatments may be an option. The highest reaction to fire classification for combustible products may then be reached. However, the excellent fire performance of the virgin fire retardant treate...
B Östman, L Tsantaridis
Effects of climatic factors and material properties on mould growth on untreated wooden claddings
2017 - IRG/WP 17-10884
Mould growth is an important contributor to colour change of untreated wood exposed outdoors. Predicting the development of mould growth is therefore important to ensure successful use of untreated wood as a façade material. More knowledge about the factors affecting mould growth on outdoor exposed wood is required to give better predictions. In this study, climatic factors and material propertie...
S Karlsen Lie, G I Vestøl, O Høibø, L Ross Gobakken
Weathering protection of European hardwoods through double modification
2017 - IRG/WP 17-30715
Beech and poplar were thermally modified, treated with melamine resin and both treatments were combined. The weathering performance (cracks and general appearance) of modified beech and poplar was assessed in natural weathering and correlated to material properties such as work in bending (WB) and Brinell hardness. In addition, the equilibrium moisture content after exposure of 12 months and subse...
G Behr, A Gellerich, S Bollmus, H Militz
Thermal stability of a wood protective biofinish and the influence of flame retardants on Aureobasidium cells
2017 - IRG/WP 17-30716
In general there is an increasing need for sustainable resources, including sustainable building materials. Wood is one of these sustainable resources and is more used as an outdoor building material. Since unprotected wood will usually be degraded during outdoor exposure, many different protection systems are available on the market. Protection systems containing biocides however might create obs...
S Rensink, E A M Klein Rot, M F Sailer
Effects of heat treatment on sound absorption coefficients in nanosilver-impregnated and normal solid woods
2017 - IRG/WP 17-40770
Effects of impregnation with silver nano-suspension as well as heat-treatment on sound absorption coefficients (AC) were studied in tangential direction of five different solid woods based on their importance. AC was measured at two frequencies of 250 and 500 Hz. A 400 ppm nanosuspension was used for the impregnation; silver nanoparticles had a size range of 30-80 nm. Based on the obtained results...
A Esmailpour, J Norton, H R Taghiyari, H Zolfaghari, S Asadi
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Is the SPM 15 effective? Survival of Pine Wood Nematode under thermal treatments
2017 - IRG/WP 17-40775
The pine wood nematode Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle (PWN) is the causal agent of “Pine wilt disease” affecting coniferous forests, and since its detection in 1999 in Portugal, has obligated the European Union to take action to prevent its spread (Decision 2006/133/CE). The main measure applied is the International Standard for Phytosanitary Measures ISPM No. 15 (ISPM ...
L Robertson, M Conde, J C Cabrero, F Llinares, M T Troya
Susceptibility to filamentous fungi of plywood for furniture coated with waterborne acrylic lacquers
2017 - IRG/WP 17-40778
Filamentous fungi (mould), thanks to their little trophic requirements belong to organisms which grow exceptionally easy and fast in favorable hygrothermal conditions and attack both organic and inorganic materials even with only trace amounts of organic substances on the surface. The fungi often cause spoilage of foodstuffs, worsen the aesthetic of wood-based elements, and pose a threat to the en...
A Fojutowski, M Nowaczyk-Organista, P Hochmańska
Studying Weathering Performance of Coatings on Thermally Modified Wood
2017 - IRG/WP 17-40805
Thermal modification and degree of improved properties depends on wood species and treatment parameters. Southern pine and spruce are the two common wood species for decking, fences and siding in North America. This study was the first to evaluate coating performance when applied on oil-heat-treated southern pine and spruce wood samples. Water uptake, colour and gloss changes of samples were analy...
M Nejad, M Dadbin, P Cooper
Influence of hygro-thermal treatment temperature and duration on dimensional stabilisation of wood modified with poly(butylene succinate)
2017 - IRG/WP 17-40813
To improve wood properties, especially dimensional stability, a treatment based on poly(butylene succinate) oligomers (OBS) was experimented. After impregnation in wood, a further hygro-thermal treatment (HTT) was carried out in a pressurized reactor at 100% relative humidity (RH) at differing temperatures for differing durations. The aim of HTT is to induce partial swelling of wood cell walls so ...
C Grosse, M Noël, L Rautkari, P Gérardin
Effects of exposure time on detection of the behavior of white-rot fungi on Oriental beech wood properties
2017 - IRG/WP 17-10902
The comparison of fungal degradation of Orientalis beechwood by two white-rot fungi was evaluated in this study. Biological, mechanical, and chemical assessments of beech wood were carried out at 30 day interval for 120 days. The results demonstrated that both fungi have greater effects on beech wood during each exposure time. However, Trametes versicolor degraded beech wood more effectively than ...
E Bari, D D Nicholas, K M Ohno
Markers of quality in self-bonded beech boards
2017 - IRG/WP 17-40820
A self-bonding phenomenon takes place when five layers of beech (Fagus Sylvatica L.) veneers are pressed at temperatures higher than 200ºC. If the pressing temperature between veneer surfaces reaches at least 225ºC during pressing and if the pressure applied is optimal, water-resistant bonds are formed between veneers. This study investigates the relation of thickness reduction (marker of compre...
C Cristescu, D Sandberg, O Karlsson
Bio-preservative properties of technical lignins from South African pulp mills: An investigation towards a conceptualized development of natural compound-based wood preservatives
2018 - IRG/WP 18-30724
The depletion of naturally durable timber and the risk posed by some of the conventional wood preservatives to human health and the environment continue to drive research efforts towards developing new formulations that are benign. Furthermore, the global concept of environmental sustainability aims at optimal use of resources and to comprehensively include conversion of waste to value added produ...
A Alade, L Tyhoda, M Meincken
Resistance of modified wood to termite attack assessed in laboratory and field testing: A review of internal research
2018 - IRG/WP 18-40824
Within the past decades, new wood modification technologies have been investigated in order to improve certain wood characteristics and enable the use of timber products for outdoor applications. Some of these non-biocidal technologies have been developed and commercialized recently. Thus, various material properties were studied intensively and shown to be improved. To a great extent, previous re...
L Emmerich, P Gascón-Garrido, H Militz
Thermodynamic properties of furfurylated wood during moisture adsorption process
2018 - IRG/WP 18-40828
Furfurylation of wood seems a promising wood modification method considering the wide raw material source of furfuryl alcohol (FA) and overall performance of FA modified wood. However, the modification mechanism of furfurylation is still not clear and needs further investigation. In this study, poplar (Populus cathayana Rehd.) samples with the size of 1(R) mm × Ф4 mm, were impregnated with ...
J Wang, J Cao, T Yang, E Ma, W Wang
An examination of the potential for the use of the Maillard reaction to modify wood
2018 - IRG/WP 18-40829
Finding efficient ways to decrease wood decay caused by fungi and increasing its dimensional stability is an important issue in the timber construction. A possible way to avoid wood decay by fungi is by reducing the water content of wood, since water is a primary condition for fungal growth. Bulking of the wood cell wall by chemical reagents occupies the space where water normally occurs. At the s...
K Peeters, E Larnøy, A Kutnar, Č Tavzes, C A S Hill