Your search resulted in 376 documents. Displaying 25 entries per page.
Characterization of waste from Pinus radiata generated during industrial thermal-treatment
2016 - IRG/WP 16-20586
The thermal-treatment is an established chemical-free process to modify wood, improving the durability and physical properties of wood through its service life. During the hydro-thermolysis several reactions from wood components occur, releasing volatile and non-volatile compounds from wood to the chamber. Once the process is accomplished, solid residues agglomerate below the wood load and gaseous...
R Herrera, D Thomas da Silva, R Llano-Ponte, J Labidi
Studying fungal growth using automated image analysis and computer simulations
2016 - IRG/WP 16-20590
Wooden materials are prone to fungal attack resulting in damage and economic losses. Therefore many efforts have been made to understand the degradation of wood and to avoid the adverse effect of fungi. Even though the extent of degradation of a material is inversely proportional to the extension of the fungi attacking it, most researchers focus mainly on the former, leaving the study of the latte...
G Vidal-Diez de Ulzurrun, J M Baetens, J Van den Bulcke, B De Baets
Preparation of Calibration Standards for the Analysis of Pentachlorophenol in Treated Wood by X-ray Fluorescence
2016 - IRG/WP 16-20591
The primary purpose of this project was to develop a method for preparing calibration standards that can be used by the wood treating industry to calibrate X-ray fluorescence instrumentation. Calibration standards of penta/P9-oil in southern yellow pine that cover the retention range of 0.2 to 0.9 pcf (0.6 to 1.9 %) were successfully prepared. A detailed procedure for mixing penta in treating sol...
L L Ingram Jr, H M Barnes, R Shmulsky, D Jeremic
Increasing the hardness of wood-composite panels by nanosilver
2016 - IRG/WP 16-40715
Effect of silver nanoparticles on hardness in medium-density fiberboard (MDF) was studied here. A 400 ppm aqueous nanosilver suspension was used at three consumption levels of 100, 150, and 200 mL/kg, based on the dry weight of wood fibers; the results were then compared with the control panels. The size range of silver nanoparticles was 30-80 nm. Composite mats were hot-pressed for 6, 8, and 10 m...
H R Taghiyari, J Norton, K Heidarhaee
Resistance of heat treated Ash wood under steam pressure: rot fungi, soil micro-organisms and termites
2016 - IRG/WP 16-40724
Thermal modification processes have been developed to increase the biological durability and dimensional stability of wood. The aim of this paper was to study the influence of ThermoWood® treatment intensity on wood decay resistance improvement against soil-inhabiting micro-organisms, brown/white rots and termite’s exposures. All of the tests were carried out in the laboratory with two differen...
K Candelier, S Hannouz, M-F Thévenon, D Guibal, P Gérardin, M Pétrissans, R Collet
How intraspecific radial variability of the European Oak’s may influence mild pyrolysis process and durability of the material
2016 - IRG/WP 16-40725
Last decades wood is promoted as building material. Unprotected wood exposed to outdoor conditions undergoes a variety of degradation induced essentially by fungi attacks. Heat treatment of wood by mild pyrolysis (180°C T 240°C under inert atmosphere) is a preservation process with a weak environmental impact, and therefore, is viewed as an interesting alternative to the chemical impregnation me...
J Hamada, A Pétrissans, F Mothe, M Pétrissans, P Gérardin
Modifying wood with paraffin wax emulsion impregnation and thermal modification: hydrophobization effect and mechanism of the combined treatment
2016 - IRG/WP 16-40726
The aim of this study was to enhance the water repellency of wood by a combined treatment of paraffin wax emulsion (PWE) impregnation and thermal modification. Two different treating procedures were used to modify the southern pine (pinus spp.). One is first PWE impregnation and then thermal modification, another is first thermal modification and then PWE impregnation. The treated samples were imm...
Wang Wang, Jinzhen Cao, Cong Chen
Fabrication and characterization of MicroPCMs filled wood-plastic composites: Effects of polyethylene glycol on melamine–formaldehyde shell material
2016 - IRG/WP 16-40728
Microencapsulated phase change materials (MicroPCMs) containing dodecanol were fabricated using melamine-formaldehyde (MF) or polyethylene glycol 200 modified melamine-formaldehyde (PMF) resin as the shell materials by in situ polymerization. Wood flour/high-density polyethylene (WF/HDPE) composites with MF shell MicroPCMs (MF-MicroPCMs) or PMF shell MicroPCMs (PMF-MicroPCMs) were prepared, respec...
Xi Guo, Jinzhen Cao
The durability of natural and thermomodified black poplar wood and Scots pine sapwood after two years of external exposition
2016 - IRG/WP 16-40730
Natural biological durability of many European wood species is considered to be relatively small, particularly in a ground contact conditions. This is due to the exposure of the wood to the range of biological and atmospheric destructive factors. This may to limit the scope of application of the wood of these species, particularly in construction. The biocides are often used for wood protection in...
A Fojutowski, A Kropacz, A Noskowiak
Dynamic mechanical analysis of viscoelastic properties of heat treated glycerol-impregnation poplar wood
2016 - IRG/WP 16-40732
The viscoelastic properties of glycerol-impregnated poplar wood after heat treatments at various temperatures were examined by dynamic-mechanical analysis. The spectra of storage modulus (E’) and loss tangent (tgδ) in the frequency at 10 Hz were measured at the temperature range from -100 to 300℃. Compared to no peak in E’ spectra and two relaxation processes in tanδ spectra of...
Li Yan
Thermoplastic Plywood at Moderately Increased Thermal Conditions
2016 - IRG/WP 16-40735
New thermoplastic plywood material so-called GradaTM manufactured by UPM has vast potential in production of wooden products with new approach of manufacturing. This paper examines possibilities of including GradaTM material in skateboard deck production as a large use of plywood type construction in this manufacturing sector. Bending strength (BS) and tensile strength perpendicular to the surface...
R Réh, M Guoth
Formation of hydrophobic wood surface by means of thermal treatment and surface modification with alkyl ketene dimer (AKD)
2016 - IRG/WP 16-40738
One of the major shortcomings of wood-based materials compared to technical materials is attributed to their poor dimensional stability in changing climates and in contact with liquid water. Heat treatment induces chemical change with a consequent decreasing of reactivity of the material showing unwanted surface inactivation. Alkyl ketene dimer (AKD) is a widely used sizing agent in papermaking, w...
T Lovaglio, T Meints, L Todaro, W Gindl-Altmutter
Durability of Thermally Modified Engineered Wood Products
2016 - IRG/WP 16-40745
In this study, rated plywood, oriented strand board (OSB), laminated strand lumber (LSL), and laminated veneer lumber (LVL) were thermally modified as a post-treatment at 140 °C, 150 °C, 160 °C, 170 °C, and 180 °C using a closed, pressurized treatment method. Eastern larch OSB manufactured from heartwood and sapwood was also thermally modified as a post-treatment at 160 °C and 180°C. All ...
H M Barnes, M D Aro, A Rowlen
The influence of log soaking temperature and thermal modification on the properties of birch veneers
2016 - IRG/WP 16-40749
In veneer manufacture the logs are routinely soaked in heated water baths in order to soften the wood prior to peeling. The temperature of the water may vary greatly between batches; however, the influence of log soaking temperature on veneer properties has had little research attention. Uncontrolled moisture is known to cause problems in wood-based materials, while thermal modification offers a m...
S Källbom, K Laine, M S Moghaddam, A Rohumaa, K Segerholm, M Wålinder
Chemical, physical-mechanical characterization and durability of thermally modified beech and ash wood by thermo-vacuum process (Termovuoto)
2016 - IRG/WP 16-40758
The paper illustrates part of the results from the CIP Eco-innovation project “Thermo-vacuum: new process for new generation of thermally modified wood”. The project is part of the 7th Framework Programme for European Research and Technological Development, and thermo-vacuum modified wood is already on the European market. The project was selected by the European Commission, EASME Agency, as "...
M Jebrane, I Cuccui, O Allegretti, N Terziev
Bacterial Degradation of Pentachlorophenol Indicated in Groundwater Undergoing Long Term In-Situ Remediation
2016 - IRG/WP 16-50318
Pentachlorophenol (PCP, Penta) is a worldwide soil and water contaminant. The pervasive use of PCP as a fungicide, herbicide, pesticide, and as preservative for wood products has led to its global distribution. It is a highly effective preventative measure for most invasive insects, bacteria, fungi, and molds, as well as an excellent wood protection treatment. This study examined a known PCP conta...
C E Stokes, H Borazjani, L Prewitt
Analysis of hindgut bacterial phyla frequency and diversity in subterranean termites exposed to chitosan-treated wood
2017 - IRG/WP 17-10882
The termite hindgut contains a microbial community that symbiotically aids in digestion of lignocellulosic materials. For better understanding of the dynamics of the bacteria-termite relationship, a species survey of bacterial hindgut microbes in subterranean termites (Reticulitermes flavipes: Kollar) collected from Louisville, Mississippi was performed after exposure to chitosan-treated and contr...
O Raji, J D Tang, T Telmadarrehei, D Jeremic
Nondestructive analysis of oviposition of the bamboo powderpost beetle Dinoderus minutus using acoustic emission and X-ray CT
2017 - IRG/WP 17-10889
The bamboo powderpost beetle Dinoderus minutus is a major pest of dry bamboo culms in Japan. In this study, acoustic emission (AE) and X-ray computed tomography (CT) was applied to the nondestructive analysis of the ovipositional behavior of adult D. minutus beetles inside bamboo pieces. Newly mated adult females were individually exposed to oviposition bamboo pieces prepared from culms of Phyllos...
H Watanabe, Y Yanase, Y Fujii
Genetic characterisation of the deathwatch beetle – Call for support
2017 - IRG/WP 17-10890
The deathwatch beetle (Xestobium rufovillosum) is one of the most important pests of historical wood constructions. Further analysis of the exact nature of the feeding habits regarding diet and wood characteristics might deliver answers for controlling this pest. Also there is little known about genetic variability and population structure within the species. For analysis of infested wood and also...
M Höpken, E Melcher, J Trautner
Use of small volume cups in XRF analysis of treated wood retention
2017 - IRG/WP 17-20602
Efforts are underway in the United States to improve the conformance of commercially-treated wood with the applicable retention standards. As part of an effort to devise a practical method for on-site assessment of within-charge retention variation, we investigated whether small-volume x-ray florescence (XRF) sample cups could be used with treated wood. A range of cup sizes, preservative types, re...
R Stelzer, A Taylor, P Lebow
Weathering protection of European hardwoods through double modification
2017 - IRG/WP 17-30715
Beech and poplar were thermally modified, treated with melamine resin and both treatments were combined. The weathering performance (cracks and general appearance) of modified beech and poplar was assessed in natural weathering and correlated to material properties such as work in bending (WB) and Brinell hardness. In addition, the equilibrium moisture content after exposure of 12 months and subse...
G Behr, A Gellerich, S Bollmus, H Militz
Thermal stability of a wood protective biofinish and the influence of flame retardants on Aureobasidium cells
2017 - IRG/WP 17-30716
In general there is an increasing need for sustainable resources, including sustainable building materials. Wood is one of these sustainable resources and is more used as an outdoor building material. Since unprotected wood will usually be degraded during outdoor exposure, many different protection systems are available on the market. Protection systems containing biocides however might create obs...
S Rensink, E A M Klein Rot, M F Sailer
Effects of heat treatment on sound absorption coefficients in nanosilver-impregnated and normal solid woods
2017 - IRG/WP 17-40770
Effects of impregnation with silver nano-suspension as well as heat-treatment on sound absorption coefficients (AC) were studied in tangential direction of five different solid woods based on their importance. AC was measured at two frequencies of 250 and 500 Hz. A 400 ppm nanosuspension was used for the impregnation; silver nanoparticles had a size range of 30-80 nm. Based on the obtained results...
A Esmailpour, J Norton, H R Taghiyari, H Zolfaghari, S Asadi
Effects of Nano-Wollastonite Impregnation on Fire Properties of Some Thermally-Treated Solid Wood Species
2017 - IRG/WP 17-40771
The effects of nano-wollastonite (NW) suspension impregnation on the fire-retarding properties of heat-treated solid wood of three species (beech, poplar, fir) were studied. Heat treatment was performed at two temperatures of 180 °C and 200 °C. Impregnation was carried out at a pressure of 3 bars for 30 min. The fire properties included ignition time, glowing time, back-darkening, back-splitting...
H R Taghiyari, R Hossinpourpia, S Adamopoulos, A Jahangiri, D Rabie
Is the SPM 15 effective? Survival of Pine Wood Nematode under thermal treatments
2017 - IRG/WP 17-40775
The pine wood nematode Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle (PWN) is the causal agent of “Pine wilt disease” affecting coniferous forests, and since its detection in 1999 in Portugal, has obligated the European Union to take action to prevent its spread (Decision 2006/133/CE). The main measure applied is the International Standard for Phytosanitary Measures ISPM No. 15 (ISPM ...
L Robertson, M Conde, J C Cabrero, F Llinares, M T Troya