Your search resulted in 808 documents. Displaying 25 entries per page.
Specifying preservative-treated resistant timber: Conforming to European Standards
2001 - IRG/WP 01-20235
The most common construction timbers used in the UK are of low natural durability and, generally, resistant to preservative treatment. These include species of spruce, hemlock and fir. However, their characteristically limited and non-uniform uptake of preservatives may still confer sufficient protection to give satisfactory durability performance in terms of biological resistance. This paper desc...
E D Suttie, A F Bravery, T B Dearling
Effects of steaming heat treatment of wood on the stimulation of termite feeding
1997 - IRG/WP 97-10212
At the 26th IRG conference, we reported that steamed Japanese larch heartwood samples were suffered a serious attack by subterranean termite, Coptotermes formosanus both in choice and no-choice feeding tests. This is possibly caused by the yield of termites stimulants in the wood samples resulting from the steaming process. Since the steaming heat treatment has often been applied to other several ...
S Doi, Y Kurimoto, M Takahashi, T Yoshimura
Comparison of three methods of quantitative evaluation of sapstain in rubberwood
2000 - IRG/WP 00-20188
Assessing the extent of fungal stain on wood during laboratory trials is a subjective process and is subjected to considerable variation between individual evaluators and specimen. The purpose of this paper was to explore the potential of three quantitative methods of wood surface measurement of rubberwood specimens degraded by sapstain and mould fungui (Botrydiplodia theobromae, Aureobasidium pul...
A J Ashari, J W Palfreyman, A H H Wong
Internal pressure development in Douglas fir lumber during pressure treatment
1997 - IRG/WP 97-40091
Preservative treatment of Douglas fir lumber to meet current industry standards poses a major challenge and a variety of methods have been developed to overcome these problems. One aspect for treatment improvement that has received less attention is the relative effect of treatment parameters on changes in pressure within the wood. Previous studies of spruce and radiata pine suggest that internal ...
P F Schneider, J J Morrell
Accidental mold/termite testing of high density fiberboard (HDF) treated with borates and N’N-naphthaloylhydroxylamine (NHA)
2003 - IRG/WP 03-10462
High density fibreboard (HDF) was made from beech and pine furnish (50:50) and treated with boric acid (0.1-3%), borax (0.1-3%) or N'-N-(1,8-naphthalyl) hydroxylamine (NHA) (0.1-1%) prior to gluing with urea formaldehyde (UF) resin in order to determine resistance to Eastern subterranean termites (Reticulitermes flavipes Kollar), the most economically important termite species in North Am...
S N Kartal, H H Burdsall Jr, F Green III
Development and field trials of Evotek 230, a new antisapstain product
1997 - IRG/WP 97-30140
Laboratory and greenhouse studies, using freshly sawn pine boards, demonstrated that the fungicidal properties of prochloraz and carbendazim were complementary for protection from sapstain and mould under extreme conditions of close stacking and high humidity. Analysis of dip bath solutions before and after dipping 20 boards showed no evidence of any stripping of the active ingredients. Neither fu...
A Adams, J Oudenweyer, J L Lindars
Treatment of wood by diffusion of salts
1976 - IRG/WP 368
A brief survey is given on the treatment of wood by diffusion of salts. The compounds used for this process, mainly boron and fluorine compounds, are mentioned and the factors influencing diffusion described. The main pre-condition is a high moisture content of the wood of above 40%. Fields of application are fresh roundwood, remedial treatment of poles and sleepers, preservation of posts and espe...
G Becker
Three-dimensional modeling of fumigant distribution in wood poles
1993 - IRG/WP 93-30025
The practice of using fumigants to control internal decay has been widely accepted in the United States and has shown to be effect in control internal decay in transmission poles and other large wood timbers. Mathematical models were developed to simulate the chloropicrin movement in utility poles after treatment. The simulation results indicated that treatment of utility poles, using either tradi...
Jing Liu, B Goodell
A new vacuum/pressure plant system
1988 - IRG/WP 3479
In the subtropical regions, the problem of wood supplying becomes more and more difficult to be solved. In that context, the Centre Technique Forestier Tropical had paid a particular attention to the valorization of products issued from plantations in dry zones of Africa. In these plantations, the products of clearings can be used as fencing, stakes or for traditional construction. However in thes...
C Dalois, R Schwartz, G R Y Déon
Field evaluation of anti-sapstain products
1987 - IRG/WP 3402
Product A based on methylenebisthiocyanate, product B based on methylenebisthiocyanate plus 2-thiocyanomethylthio-benzothiazole, product C based on 2-thiocyanomethilthio-benzothiazole and product D based on didecyl dimethil ammonium chloride plus 3-iodo-2 propynil butyl carbarnate were evaluated on Pinus radiata sawn timber as fungicides for sapstain and mould in the Sawmill Division of the Univer...
M C Rose, A Bedoya
Evaluation of the effectiveness of Tuff Brite C in the control of sapstain in laboratory and field tests
1992 - IRG/WP 92-3718
Since 1990, the anti-sapstain product Tuff Brite C (ASC 66898) has been evaluated internationally in laboratory and field tests, and has been commercially introduced in New Zealand. The product is an aqueous flowable formulation of chlorothalonil and carbendazim. Efficacy tests which have been carried out in New Zealand, Australia, USA, South Africa and Europe are described and summarized. Tuff Br...
T L Woods, C J Klaver
Performance of proprietary formulations of anti-sapstain preservatives on Hevea brasiliensis timbers in laboratory tests
1989 - IRG/WP 3532
A total of 10 proprietary and two experimental formulations were assessed for their effectiveness against sap-stain caused by Botryodiplodia theobromae on Rubberwood (Hevea brasiliensis). Sterilized wood samples 5x20x40 mm³ were dipped in the test chemicals for 60 seconds and then inoculated with 0.5 ml of culture filtrate of Botryodiplodia theobromae for incubation in sterile, damp petri dishes....
L T Hong
Multiple-Phase Pressure (MPP) Process: One-stage CCA treatment and accelerated fixation process. 4. MPP compared with other processes for achieving acceptable treatment of radiata pine heartwood
1998 - IRG/WP 98-40115
Although radiata pine sapwood is very amenable to preservative treatment, it is often difficult to achieve the required standard for heartwood treatment.
A preliminary investigation showed that to achieve the NZ Timber Preservation Council minimum penetration requirements for radiata pine heartwood using the Multiple-Phase Pressure (MPP) Process, a hydraulic pressure of at least 1250 kPa for 20 m...
K Nasheri, J A Drysdale, G Durbin, M E Hedley
The effect of synthetic pyrethroid insecticides on post-treatment emergence of Anobium punctatum
1992 - IRG/WP 92-1568
Data is presented from trials in which wood specimens, treated with a range of remedial insecticidal formulations, were aged in a roof void for 5 years and then tested for emergence of adult Anobium punctatum. The technique used followed that described in IRG/WP/2175. The results from formulations containing synthetic pyrethroids are compared with those from formulations containing the chlorinated...
R W Berry
Bending strength of heat-treated spruce and pine timber
2002 - IRG/WP 02-40242
Heat-treatment of spruce (Picea abies) and pine (Pinus sylvestris) beams (45 x 145 mm) gave a reduction in bending strength of approximately 50%. The bending stiffness (modulus of elasticity) only decreased by 3.5%. Tests were carried out according to EN 408. Another effect of the heat-treatment was increased variation in bending strength. The 5th percentile value of the bending strength, the so c...
C Bengtsson, J Jermer, F Brem
Treatment groups and remedies for CCA treated hardwood and softwood poles
1999 - IRG/WP 99-40142
Different hardwood and softwood species from Bangladesh and Bhutan was investigated regarding density, green fiber stress, natural durability of heartwood and CCA treated sapwood, CCA treatability grades, sapwood thickness, and kiln-drying properties for long term use as electric poles. These properties along with the past service records for nineteen years, separated ten heardwood and five softwo...
A K Lahiry
Thickened boron treatment
1990 - IRG/WP 3632
Commercial trials with thickened boron preservatives "Diffusol™" indicate a number of advantages when compared to traditional methods of dip-boron preservative treatment. These include: (i) more even uptake and distribution of preservative on and within the timber; (ii) faster diffusion times; (iii) the treatment of gauged timber (though improved retention); (iv) saving in energy costs (heating ...
P Vinden, J A Drysdale, M Spence
Treatment of wood with boron esters
1995 - IRG/WP 95-30087
The treatment of wood and wood products with boron esters is reviewed. The physical and chemical characteristics of boron esters affecting the treatability of wood are discussed, in particular thermal decomposition and rates of hydrolysis. The uses and methods applying boron esters as wood preservatives include: (i) Solutions of boron esters for remedial and diffusible treatment of wood; (ii) soli...
J Romero, P Vinden, J A Drysdale
Gaseous preservative treatment of wood
1990 - IRG/WP 3631
A recent development in processing wood with a gaseous preservative means that dry, treated wood can be produced in under 30 hours with the benefits of product diversification, faster stock turnover and the ability to respond to short term demand. About 400,000 m³ of wood are treated each year in New Zealand with boron salts to protect from borer infestation. Traditionally this treatment is effec...
R Burton, A J Bergervoet, K Nasheri, P Vinden, D R Page
Screening of fungal strains for wood extractive degradation
1998 - IRG/WP 98-10254
Fungal strains were screened for their ability to degrade apolar extractives in wood from scots pine. The degradation of total wood extractives by 91 different strains was monitored in stationary batch assays incubated for 6 weeks. The results obtained show that the ability of wood-inhabiting fungi to utilize wood extractives varied greatly, even for different isolates of the same species. Fungal ...
J Dorado, M J Martinez-Inigo, T A van Beek, F W Claassen, J B P A Wijnberg, R Sierra-Alvarez
A new factory applied preservative treatment for joinery
2002 - IRG/WP 02-40246
Conventional pre-treatment processes involve the principle of applying preservatives to the external surfaces of wood to achieve the necessary penetration and retention of the chemicals although the heartwood remains difficult to treat.
The present development involves the production of internal reservoirs within new joinery components, which are subsequently filled with a specially developed g...
I M Robertson, W Beauford
Environmental characterisation of retification process by-products (liquid and gaseous wastes)
2005 - IRG/WP 05-50224-10
In order to reduce environmental risks during the service life of the treated wood and to find new alternative developments on the durability of wood, some research and technology development have been made on thermal treatment. The retification process is one of these processes. The retification process induces chemical modification of the lignin and cellulosic components and modifies the intrins...
G Labat, E Bucket, S Legay, C Yriex, P Marchal, E Raphalen, M Vernois, R Guyonnet, H Besset, E Fredon), G Vilarem, L Rigal, C Raynaud
Wood preservatives treatment of black spruce
1997 - IRG/WP 97-40092
A representative sample of black spruce logs from Central Newfoundland was harvested and processed to dressed 2"x4" lumber. Over 400 pieces of lumber were then incised and treated with ACQ preservative in a semi-industrial retort. 9 charges of 20 samples were used to determine treating parameters and 11 charges of 20 pieces were treated using the optimized process. This material was inspected by a...
A R Zahora, J P Hösli
Characteristics of thermally modified wood in vacuum
2004 - IRG/WP 04-40287
In commercial thermal wood modification processes nitrogen, steam or oil has been used for the reduction of oxygen content in the reactor atmosphere. In present study no special heating medium, but an initial vacuuming step has been used for this purpose. Mass loss, resistance to fungal decay, dimensional stability, bending strength and modulus of elasticity of heat treated wood were evaluated and...
G Rep, F Pohleven, B Bucar
Conservation of Nypa fruticans and Indigenous Timber Species of Sundarban Mangrove Forest of Bangladesh by Using Preservative Treatment.
2005 - IRG/WP 05-40297
This report describes the possibilities and benefits of preservative treatment of some Bangladeshi wood species. It is concluded that:
Heartwood of Sundri is not easily treatable. The treating schedule of 14.1 kg/cm² pressure and eight hours treatment period may be used for treating sundry logs. During the treatment of Sundri wood must not mix with other species. Other timber species such as Gew...
G N M Ilias