Your search resulted in 280 documents. Displaying 25 entries per page.
Glue-bond strength of simul (Bombax ceiba) plywood made of Neem (Azadiracta indica) leaves treated veneers
2013 - IRG/WP 13-40647
The glue-bond qualities of plywood made of treated simul (Bombax ceiba) veneers were investigated. The veneers were treated with cold and hot water solution of neem (Azadiracta indica, A. Juss.) leaves of different concentrations and treatment durations. The plywoods were made at three different pressures in hot press using urea formaldehyde glue. The glue-bond strength of untreated simul plywood ...
K Akhter, M A Hashem, S Akhter
Dynamic mechanical analysis (DMA) of nano cupric oxide (CuO) modified aqueous phenol formaldehyde (PF) resin
2014 - IRG/WP 14-40654
Phenol formaldehyde (PF) resins, modified by nano CuO incorporating alkane surfactant and polyvinyl alcohol (PVA) 17-99, were analyzed by dynamic mechanical analysis (DMA). The mechanical properties of its bonded plywood including tensile strength, modulus of rupture (MOR), modulus of elasticity (MOE) and shear strength under five test conditions were evaluated. Results indicated that the incorpor...
Wei Gao, Guanben Du
Improving dimensional stability of thermally treated wood by secondary modification – potential and limitations
2014 - IRG/WP 14-40664
The potential of treating thermally modified wood with melamine resin to improve the dimensional stabilization is tested in this research. Two different boards of poplar (Populus ssp.) were cut into two halves. One half of each board was thermally modified (T1 and T2) in a commercial process, the other half was used as untreated reference material. The material was thermally modified using the vac...
G Behr, K-C Mahnert, S Bollmus, H Militz
Development of composite furniture using bamboo strips, bamboo mat and rubber wood veneer
2014 - IRG/WP 14-40679
Bamboo offers cost-effective component in panel form is well suited to wood substitute can be used as furniture components. In the present study, borak (Bambusa balcooa ) bamboo were used for manufacturing bamboo panel. Mitinga (B. tulda) bamboo were used for making mat and rubber wood veneers were used for manufacturing mat overlaid veneer board. Borax-boric acid (BB) treatments were given to enh...
K Akhter, M Mahabubur Rahaman, M H Chowdhury, M Zahirul Alam
Penetration of phenol formaldehyde (PF) resin into beech wood studied by light microscopy
2015 - IRG/WP 15-20558
In this study, we examined the distribution and penetration depth of phenol-formaldehyde (PF) resin into wood specimens by light microscopy (LM). Two PF resins from different producers, of concentrations 9, 18 and 27 wt % in water, were vacuum impregnated into European beech wood (Fagus sylvatica) blocks of 15x25x50 mm³. The presence of chemical agent in the wood was carried out by way of their i...
V Biziks, S Bicke, H Militz
Decay resistance of beech wood and plywood treated with different type of phenol-formaldehyde (PF) resins
2016 - IRG/WP 16-40717
In this study treatment of beech and poplar wood veneers with (PF) resin industrial scale and screening tests of nine different phenol-formaldehyde (PF) resins were made. Specifically, the effect of different phenol-formaldehyde (PF) resin types on the resistance of beech wood against brown- and white-rot fungi was evaluated. Criteria for selection of optimal (PF) resin were based on minimum WPG ...
V Biziks, S Bicke, H Militz
Marine Borer Resistance of Acetylated and Furfurylated Wood – Results from up to 16 years of Field Exposure
2016 - IRG/WP 16-40756
Furfurylated and acetylated Scots pine sapwood has been tested since 1999 in a marine field with high marine borer activity. In 2004, two test groups with acetylated southern yellow pine (product later known as Perennial Wood™) were put out and over the whole test period differently furfurylated wood (later marketed as Kebony®) test groups have been started. Furthermore, some combinations of mo...
M Westin, P Larsson Brelid, T Nilsson, A O Rapp, J P Dickerson, S Lande, S Cragg
Lignin-Based Adhesive for Engineered Wood Products
2016 - IRG/WP 16-50319
Lignin as a naturally occurring polyphenolic compound has an excellent potential to replace petroleum-based phenol in formulation of phenol-formaldehyde adhesive that are used in manufacturing of engineered wood products. However, there are three major obstacles in application of polymeric lignin as phenol replacement: 1) low reactivity toward phenol, 2) high molecular weight, and 3) high polydisp...
I Kalami, M Arefmanesh, E Master, M Nejad
Weathering protection of European hardwoods through double modification
2017 - IRG/WP 17-30715
Beech and poplar were thermally modified, treated with melamine resin and both treatments were combined. The weathering performance (cracks and general appearance) of modified beech and poplar was assessed in natural weathering and correlated to material properties such as work in bending (WB) and Brinell hardness. In addition, the equilibrium moisture content after exposure of 12 months and subse...
G Behr, A Gellerich, S Bollmus, H Militz
Superior kempas hardwood protection with two proprietary microemulsion termiticdes based on permethrin and cyermethrin against Coptotermes termite attack under H2 an H3 weathered conditions found in buildings
2018 - IRG/WP 18-10931
SARPECO® and AXIL® solutions are water-based wood preservatives approved for dipping treatment providing 25 years of termite protection for solid wood and wood-based products in Europe and for more than 10 years in Indonesia. SARPECO® and AXIL® solutions are patented formulations based on concentrated microemulsions (ME) diluted with water as a dipping treatment but also for vacuum pressure tr...
D Messaudi, A H H Wong, C A D Tawi, N Bourguiba, O Fahy
Properties and potential use of Irvingia gabonensis and Irvingia wombolu kernel extracts as natural wood adhesives: Towards formaldehyde free wood composite products
2018 - IRG/WP 18-40832
Irvingia species are widely distributed in central and West Africa as well as parts of Asia and are earmarked for domestication due to the multitude of potential products that can be obtained from them. With renewed interest in renewable sources, the current study establishes the feasibility of utilizing extracts from Irvingia gabonensis and Irvingia wombolu kernels as wood adhesives. Proximate an...
A O Alawode, S O Amiandamhen, M Meincken, L Tyhoda
Application of nano metal fluorides against termites
2019 - IRG/WP 19-30733
Recent research has shown that fluorides such as NaF have potential as a wood preservative against termite attack (Pan and Wang, 2015). However, NaF has high leaching susceptibility because of its solubility (40 g/l ) which can reduce its efficacy over long term. Metal fluoride nanoparticles such as MgF2 and CaF2 present a viable alternative to water soluble fluoride-based wood preservatives as th...
S M Usmani, K Klutzny, Y de Laval, R Plarre, D McMahon, I Stephan, T Hübert, E Kemnitz
Exemplary aboveground hardwood protection from Coptotermes curvignathus under weathered conditions conferred by proprietary microemulsion-based cypermethrin (SARPECO®) and permethrin (AXIL®) biocides
2019 - IRG/WP 19-30749
SARPECO® (with cypermethrin) and AXIL® (with permethrin) solutions are water-based wood preservatives approved for dipping treatment providing 25 years of termite protection for solid wood and wood-based products in Europe and for more than 10 years in Indonesia. SARPECO® and AXIL® solutions are patented formulations based on concentrated microemulsions (ME) diluted with water as a dipping tre...
D Messaoudi, A H H Wong, C A D Tawi, N Bourguiba, O Fahy
Improvement of wood decay and termite durability resulting from combined treatments based on borax/phenol-formaldehyde impregnation followed by thermal modification
2019 - IRG/WP 19-40871
This study determined the factors influencing the boron content after leaching of pine blocks impregnated with aqueous solution of phenol-formaldehyde (PF) resin with or without borax and subjected to heat treatment by response surface methodology. An experimental design permits to analyze the effects of heat treatment temperature (150, 185 and 220°C), curing time (5, 12, 5 and 20 hours), resin c...
S Salman, M-F Thevenon, A Petrissans, S Dumarcay, P Gerardin
Longterm Performance of Treated Timbers in Marine Exposures
2020 - IRG/WP 20-10969
The performance of preservative-treated or modified woods in marine exposures was evaluated at test sites in Newport, Oregon, USA and Brisbane, Queensland, Australia. All samples have exhibited excellent performance at the Newport, Oregon site, while attack was more aggressive at the sub-tropical Brisbane site. Acetylated wood as well as samples treated with 7.3% chromated copper arsenate (CCA-T...
M Konkler, A R Zahora, J Norton, J J Morrell
Performance of resin-treated solid wood and laminated veneer lumber (LVL) under marine conditions
2021 - IRG/WP 21-10973
Wood is a traditional building material in the marine environment, where it is exposed to extremely harsh conditions. Most of the indigenous softwood and hardwood species in Europe are not durable against attack by marine organisms. Recently, wood modification has been considered as an alternative to protect non-durable wood species under use class (UC) 5 (EN 335, 2013) conditions. The present stu...
L Emmerich, C Brischke, S Bicke, H Militz
Phenol formaldehyde modification and termite resistance under laboratory testing
2022 - IRG/WP 22-40952
The development of phenol formaldehyde (PF) resins as a means of impregnating solid wood is one that has been explored for several decades, both in terms of conventional impregnation processing (Impreg) or compressional impregnation (Compreg). However, it is only recently with advances in processing conditions that the method truly affords a means of achieving conventional modification for solid t...
L Nunes, A Pitman, M Duarte, B Stefanowski, D Jones
A novel method for assessing radial variation in termite resistance of timber
2023 - IRG/WP 23-11005
Australia has many timbers whose heartwood is highly resistant to fungal and termite attack; however, changing public policies have resulted in restricted access to many native forests where these species are found. Plantations of these same species are expected to replace these resources, but there are questions concerning whether timber from these trees will have the same resistance as the nati...
S Kleinschmidt, R McGavin
Long-term Performance of Treated Timbers in a Sub-tropical Marine Exposure
2023 - IRG/WP 23-11015
The long-term performance of preservative-treated and modified wood in marine exposures was assessed in Brisbane, Queensland, Australia. This report describes the final destructive assessment of the surviving Australian panels after 11 years of exposure. This site presents the potential for attack by shipworms (likely Bankia spp.), pholads (Martesia striata), Limnoria and Sphaeroma terebrans. Mos...
E L Galore, J Norton, A Zahora
Efficacy of a wide-spectrum plant bio-based anti-termite product - Laboratory trials
2023 - IRG/WP 23-11024
Compared to the number of timbers available, the list of wood species resistant to termites is rather limited and largely composed of tropical timbers. In addition, due to climate change and environmental degradation, together with global trade, a significant global expansion of termites is predicted along with the economic losses due to their activities. Therefore, there is a demand to find produ...
M-F Thévenon, F Chopinet, J Vuillemin, A Robert, S Lafay, D Messaoudi
A novel wood preservative with vegetal extracts-cypermethrin mixture protects H2-weathered envelope-treated tropical hardwood kempas against Coptotermes termites
2023 - IRG/WP 23-30794
In accordance with sustainability development initiatives by commercial wood protection to conceive of cost-effective, environmentally acceptable wood treatment solutions replacing traditional biocides, this paper reports an aboveground subterranean termite test of termite-susceptible heartwood blocks of the tropical (Malaysian) structural hardwood kempas (Koompassia malaccensis) envelope-treated ...
D Messaoudi, A H H Wong
Envelope wood protection against subterranean termites under H2-hazard class tropical environment by a new generation wood preservative with vegetal extracts-cypermethrin mixtures
2023 - IRG/WP 23-30795
Wood protection industries in progressive economies globally are compelled to develop cost-effective, environmentally acceptable wood treatment solutions for long term carbon storage in wood materials/products while appealing to consumer demands for low environmental impact treated wood. A new generation wood preservative, based in part on 2% vegetal extracts and 0.16% cypermethrin components, has...
D Messaoudi, A H H Wong
Control of Asian subterranean termites Coptotermes gestroi (Blattodae: Rhinotermitidae) by a new generation bait system with vegetal extracts-diflubenzuron mixture
2023 - IRG/WP 23-30797
The efficacy of anti-termite bait pebble dosed at 0.3% w/w of Diflubenzuron, and Chitin Synthesis Inhibitor (CSI) and 0.6% w/w of vegetal extract from Berkem Biosolutions®, was evaluated in the laboratory on the Asian subterranean termite Coptotermes gestroi (Wasmann). Four concentrations 33.3%, 50%, 50% bis and 100% as well as two neutral matrices, were used in two in-house developed test method...
F Chopinet, D Messaoudi
Resistance of phenol formaldehyde impregnated beech (Fagus sylvativa L.) LVL against biodegradation in soil contact
2023 - IRG/WP 23-40965
Alternatives to preservative impregnation are emphasized in Germany and other European countries. Even though these treatments significantly improve wood's resistance to decay, they often do not have a beneficial impact on the dimensional stability. One alternative product, which may be used in ground contact for items like poles and railway sleepers, could be beech (Fagus sylvatica L.) laminated ...
M Slabohm, C Brischke, S Bicke, H Militz
Laboratory evaluation of PA1b, an insecticidal protein extracted from pea seeds (Pisum sativum), as bait active ingredient against the subterranean termite Coptotermes gestroi (Blattodea: Rhinotermitidae) in tropical zones
2024 - IRG/WP 24-11038
Coptotermes gestroi (Wassman 1896) is one of the worst pests in tropic areas, economically. Two types of curative methods are used since decades to eliminate colonies that attack constructions: injection of biocidal treatment solutions on wood, walls and soil, and population control using baits. In application of the current regulations, the first technique can no longer be used in Europe, to lim...
J Vuillemin, D Messaoudi, P da Silva