Your search resulted in 271 documents. Displaying 25 entries per page.
Effects of teak, Tectona grandis Linn, heartwood extractives against Heterotermes indicola (Isoptera; Rhinotermitidae)
2018 - IRG/WP 18-10910
Heartwood extractives from Tectona grandis were investigated for antitermitic activities against Heterotermes indicola in laboratory experiments. Extractives were removed from wood shavings by soxhlet extraction using an ethanol: toluene (2:1) solvent system. Termite feeding and mortality followed a concentration dependent response. The highest termite mortality occurred at an extractive concentra...
B Hassan, S Ahmed, M Mankowski, G Kirker, R E Ibach, M Misbah ul Haq
Impact of fungal decay on the bending properties of wood
2020 - IRG/WP 20-20671
Wood used outdoors is generally prone to fungal degradation, and its impact on the structural integrity of wood is an immanent factor for service life planning with timber. Wood decayed to very small mass losses can suffer from a significant reduction in mechanical strength and elastic properties. Hence, the latter are preferred indicators to detect decay in wood durability studies. Numerous previ...
S Bollmus, P B van Niekerk, C Brischke
Mechanical and biological durability properties against soft-rot and subterranean termite in the field (grave-yard test) of beech wood impregnated with different derivatives of glycerol or polyglycerol and maleic anhydride followed by thermal modification in an opened or in a closed system
2021 - IRG/WP 21-40917
This paper presents mechanical and biological durability properties in soil beg test (soft-rot test) and field test (grave-yard test) against subterranean termite of the wood modified with an aqueous vinylic derivative of glycerol/polyglycerol or maleic anhydride cured in an opened or in a closed system. Wood modification was performed through impregnation of European beech (Fagus sylvatica) with ...
M Mubarok, H Militz, S Dumarcay, I W Darmawan, Y S Hadi, P Gerardin
Effect of Heat Treatment on Physical and Mechanical Properties of Oriental Beech Wood (Fagus orientalis L.)
2021 - IRG/WP 21-40923
The present study aims to investigate the influence of heat treatment on physical and mechanical properties of Oriental beech wood (Fagus orientalis Lipsky.). Samples were exposed to temperature levels of 130˚C, 160˚C, and 190˚C for 3, 6, and 9 h. Selected physical and mechanical properties including compression strength parallel to grain, compression strength perpendicular to grain, bending st...
M D Ghalehno, D Chu, B N Sheshkal, M Humar, M Bahmani
Changes in topochemistry and mechanical properties of Beech (Fagus orientalis L.) by natural fungus infestation
2022 - IRG/WP 22-10986
Beech is one of the major hardwood species in Europe. It is, however, highly susceptible to fungal attack both in the fresh state and during the storage. Understanding the alteration in chemical and mechanical properties of beech wood during the initial degradation state can lead to improved raw material utilization. Therefore, UV-microspectrophotometer (UMSP) and High-Performance Liquid Chromatog...
H Sivrikaya, M Rehbein, F Divos, S Adamopoulos, R Hosseinpourpia
Evaluation of ecotoxicological effects of different coniferous wood treatments on two marine bioindicator species
2022 - IRG/WP 22-10999
Coniferous wood panels (Picea abies) were treated with two concentrations of copper-based impregnating agent to increase its durability in marine and brackish environment. In order to assess the environmental compatibility of the treatments a laboratory experiment was conducted with two marine invertebrate species: bivalve Mytilus galloprovincialis and a gastropod Steromphala albida. The bioindica...
T Marčeta, N Nesto, I Guarneri, D Tagliapietra, V Moschino
Effects of Borax and Boric Acid as Fire Retardants on the Resistance of Pterygota macrocarpa Wood to Fire Tests
2022 - IRG/WP 22-30770
The combustible nature of wood as a building material, when exposed to hazards of fire underscores the reason for fire retardant treatments. Pterygota macrocarpa wood is commonly used by builders in Nigeria for roof and other structural applications. Therefore, this study was carried out to assess the effect of Borax and Boric acid on the fire-retardant properties of P. macrocarpa wood. Wood sampl...
J M Owoyemi, O Apogbona, T O Akinwamide
Environmentally Friendly Wood Modification based on Tannin-Furfuryl alcohol - Effect on stabilisation, mechanical properties and decay durability
2022 - IRG/WP 22-40929
Furfurylation is a well-known wood modification technology. This paper studied the effect of tannin addition on the wood furfurylation. Three kinds of dicarboxylic acids, adipic acid, succinic acid, and tartaric acid, as well as glyoxal as a comparing agent, were used to catalyse the polymerisation of furanic or tannin-furanic solutions during wood modification. Impregnation of furanic or tannin-f...
M Mubarok, E Azadeh, F O Akong, S Dumarçay, A Pizzi, C Charbonnier-Gérardin, P Gérardin
Mechanical Properties of Thermally Modified Wood after twelve Months of Field Exposure
2022 - IRG/WP 22-40945
This study aimed to evaluate the durability and mechanical properties of two different woood species, namely beech (Fagus sp.) and silver fir (Abies alba), from Bosnia and Herzegovina thermally modified at three different temperatures and duration at maximum temperature. Samples of the mentioned wood species wood (Abies alba) were prepared according to EN 408+A1 standard. The maximum 4-point bendi...
R Hasanagić, M Bahmani, L Fathi, M Humar
Effect of densification of Eucalyptus nitens and E. obliqua on moisture uptake, swelling, decay resistance, and fire performance
2022 - IRG/WP 22-40946
Some Australian Eucalyptus species that are abundantly available have low natural durability and poor resistance to fire. These same species are also extremely difficult to treat with preservatives or fire retardants using conventional pressure treatment methods due to a large proportion of refractory heartwood. The aim of this research was to understand whether thermo-mechanical densification had...
B Hassan, J J Morrell, F Wiesner, W Wu, B Belleville, K C Wood
Influence of weathering on the mechanical properties and performance of exterior wood coatings
2022 - IRG/WP 22-40951
Three commercial coatings were exposed to artificial (EN 927-6) and natural weathering (EN 927-3) on wood samples. Cracking was visually assessed as well as Persoz hardness. Free films of the same coatings were also exposed to the same weathering tests before their tensile properties were measured. Results show that artificial and natural weathering modified the overall mechanical properties of wo...
L Podgorski, J-D Lanvin
Biocomposites based on PVA, cellulose nanofibrils and tannic acid
2022 - IRG/WP 22-40957
Biocomposite films based on a polyvinyl alcohol (PVA) with the addition of cellulose nanofibrils (CNF) as a reinforcing component and with the addition of the biologically active tannic acid (TA) were prepared. The influence of different additions of CNF and TA in the polymer matrix PVA on the mechanical properties, improvement of hydrophobicity of the prepared films was studied. In all cases, the...
U Osolnik, V Vek, I Poljanšek, Poven
A simple method for assessing the effects of lyctid beetle attack on longitudinal compressive strength of spotted gum sapwood
2023 - IRG/WP 23-20700
Lyctid beetle attack is commonplace in a significant proportion of spotted gum utility poles that are air seasoned prior to chromated copper arsenate (CCA) treatment. While this damage is allowed, there are no reports quantifying the effects of the beetle galleries on pole properties. Full scale testing would require substantial quantities of poles in order to obtain a range of degrees of damage....
M Powell, J J Morrell
Biological durability and wood-water interactions of sorbitol and citric acid modified wood – Effects on the expected service life
2023 - IRG/WP 23-40960
A high level of research activities on sorbitol and citric acid (SorCA) modified wood has been recognized in Europe over the last few years. As this treatment is close to entering an industrial-scale production, it is of interest to investigate how such treated wood performs upon long-term outdoor exposure. Hence, in this study Scots pine (Pinus sylvestris L.) sapwood was modified with aqueous sol...
K Kurkowiak, L Emmerich, H Militz
Effect of impregnation modification treatment on properties of Paraserianthes falcataria wood
2023 - IRG/WP 23-40966
Modification treatment can improve the properties of wood, particularly those of fast-growing species. Paraserianthes falcataria, also known as batai, is a fast-growing species with low wood density. This species has piqued the interest of those involved in industrial wood processing as a promising alternative for construction. The aim of this study is to improve the dimensional stability of batai...
A S Yusoh, A S Boneka, M K Anwar U, S Salim, S H Lee
Effects of preservative impregnations on wettability and surface free energy properties of Eucalyptus grandis wood
2023 - IRG/WP 23-40978
Wettability and surface free energy (SFE) are crucial parameters for evaluating the adhesion thermodynamics of solid surfaces. Hence, this study investigated the effects of copper azole (CA) and disodium octaborate tetrahydrate (DOT) preservative impregnations on Eucalyptus grandis wood wettability and SFE. Wettability was determined in terms of contact angles with polar (water) and non-polar (dii...
A A Alade, C B Wessels, H Stolze, H Militz
Failure characteristics of thermally modified poplar wood subjected to mechanical tests
2023 - IRG/WP 23-40983
Poplar (Populus spp.) are among the fastest growing timber species and have been widely planted for use in plywood, composites, pallets, furniture components and paper production. However, the low density of the wood limits many structural applications and the wood has little resistance to biodegradation. Thermal modification represents one approach to improving durability by changing the moistur...
E Bari, M Ghorbanian Far, N Moradi, J J Morrell, G Daniel, B Mohebby, R Hosseinpourpia, M Humar
Japanese traditional wooden building construction project in Bangkok - Part 1 Project outline, building implementation and effects
2023 - IRG/WP 23-40992
The purpose of this project is to build new ways to utilize wooden resources in Japan. Japan's forestry industry is in decline despite its abundant forest resources due to a lack of successors and other reasons. Meanwhile, in Southeast Asian countries, reinforced concrete houses, which are not suited to the climate, are on the rise due to a lack of wood and technology. To solve these problems in b...
S Murakami, K Kawaguchi, H Ishiyama
Effects of phosphoric acid and diammonium phosphate treatments on the physical and fire-retardant properties of five selected Nigerian wood species
2024 - IRG/WP 24-20713
Wooden products in buildings are major sources of fuel for fire outbreaks. Effects of phosphoric acid and diammonium phosphate treatments on the physical and fire-retardant properties of wood species commonly used in buildings were evaluated. The timber species utilized in this study were sourced from the sawmill sector located in Akure, Nigeria, encompassing Brachystegia laurentii, Khaya ivorensi...
J Owoyemi, T O Akinwamide, O M Ibrahim, E A Iyiola
Elevated pressure hybrid wood modification: Synergistic effects on durability performance
2024 - IRG/WP 24-20725
The combination of different wood modification technologies to obtain improved performance is increasingly receiving attention in research. In this study, Scots Pine was impregnated with furfuryl alcohol (FFA) in pure aqueous 20, 40 and 60% solution strength without adding any catalyst. In a second step, the FFA was polymerized while simultaneously performing thermal modification in a closed syste...
P Klaas, D Jones
The durability and mechanical properties of 40 years old Black locust poles
2024 - IRG/WP 24-11042
This study investigates the durability and mechanical properties of 40-year-old black locust (Robinia pseudoacacia) poles harvested from a vineyard in Slovenia. Wood from these poles was compared to recently harvested black locust wood to determine possible reuse options. Visual inspection, hyperspectral imaging, and laboratory tests were conducted to assess decay, density, mechanical properties, ...
M Humar, J Malik, J Levanic, D Krzisnik, E Kerzic, B Lesar