Your search resulted in 346 documents. Displaying 25 entries per page.
How intraspecific radial variability of the European Oak’s may influence mild pyrolysis process and durability of the material
2016 - IRG/WP 16-40725
Last decades wood is promoted as building material. Unprotected wood exposed to outdoor conditions undergoes a variety of degradation induced essentially by fungi attacks. Heat treatment of wood by mild pyrolysis (180°C T 240°C under inert atmosphere) is a preservation process with a weak environmental impact, and therefore, is viewed as an interesting alternative to the chemical impregnation me...
J Hamada, A Pétrissans, F Mothe, M Pétrissans, P Gérardin
Fabrication and characterization of MicroPCMs filled wood-plastic composites: Effects of polyethylene glycol on melamine–formaldehyde shell material
2016 - IRG/WP 16-40728
Microencapsulated phase change materials (MicroPCMs) containing dodecanol were fabricated using melamine-formaldehyde (MF) or polyethylene glycol 200 modified melamine-formaldehyde (PMF) resin as the shell materials by in situ polymerization. Wood flour/high-density polyethylene (WF/HDPE) composites with MF shell MicroPCMs (MF-MicroPCMs) or PMF shell MicroPCMs (PMF-MicroPCMs) were prepared, respec...
Xi Guo, Jinzhen Cao
Evaluation of Commercially Available Polyurethane Resin to Develop Non-biocidal Wood Preservation Treatments
2016 - IRG/WP 16-40751
Evaluation of commercially available polyurethane (PU1 and PU2 and polyisocyanate (PNCO) to develop non-biocidal wood preservation treatments have been conducted. A simple method by vacuum impregnation of these resins into beech wood (Fagus sylvatica L) and pine wood (Pinus sylvestris L.) samples followed by varied curing process at ambient temperature, 103oC, and 200oC have been performed. Based ...
M Mubarok, Y Sudo Hadi, J Suryana, I W Darmawan, F Simon, S Dumarcay, C Gérardin, P Gérardin
Influence of pressure phase impregnation time on the uptake and distribution of wood preservatives in Scots pine material of diverse treatability
2016 - IRG/WP 16-40752
In spite of the general opinion that Scots pine sapwood is easy to impregnate considerable variations in treatability are reported. In order to study impregnation results of diverse Scots pine sapwood treated with increasing process times, Scots pine sapwood from two different predefined treatability groups was impregnated. A copper solution was used as impregnation agent in ten different vacuum p...
K Zimmer, B Kerfriden
Evaluation of the effects of different concentrations of Fipronil against Reticulitermes grassei (Blattodea: Rhinotermitidae)
2016 - IRG/WP 16-30702
A laboratory evaluation of the effect of different concentrations of Termidor (fipronil at 9.09%) has been carried out. Six concentrations (10,000; 1,000; 100; 50; 10 and 5 ppm) have been tested in two different colony models imitating an open environment.
After five days treatment, mortality data were collected. The three higher concentrations showed nearly 100% mortality. At 50 ppm the mortalit...
J R Carbonero-Pacheco, R Molero, M E Alcaide, J Diz, M Gaju
Durability Testing of a Cattail (Typha spp.) based Insulation Material against Termite Attack
2017 - IRG/WP 17-10879
The use of insulating materials is particularly important in the construction industries, especially with regard to the use of wood and naturally occurring substances. The use and durability of natural materials as insulating materials is of keen interest to many construction experts, and continues to be a topic of intense investigation. It is generally agreed that the use of natural substances ...
M Dass, W Unger, T L Woods
Comparative studies on the durability of English oak (Quercus robur L.) under in-service, field and laboratory conditions
2017 - IRG/WP 17-10881
The durability of many wood species varies due to differences in extractive content, anatomical features, growth conditions, and not at least in dependence of the respective exposure conditions either under test or in real life applications. And so does the durability of English oak (Quercus robur L.), which has recently been considered in the revised European standard EN 350 (2016) and is now cla...
C Brischke, L Meyer-Veltrup, A Soetbeer, M Höpken, E Melcher, J Trautner
Effects of climatic factors and material properties on mould growth on untreated wooden claddings
2017 - IRG/WP 17-10884
Mould growth is an important contributor to colour change of untreated wood exposed outdoors. Predicting the development of mould growth is therefore important to ensure successful use of untreated wood as a façade material. More knowledge about the factors affecting mould growth on outdoor exposed wood is required to give better predictions. In this study, climatic factors and material propertie...
S Karlsen Lie, G I Vestøl, O Høibø, L Ross Gobakken
Design and performance prediction of timber structures based on a factorization approach
2017 - IRG/WP 17-20603
Service life of timber structures in outdoor conditions is predominantly affected by the climatic conditions in terms of moisture and temperature over time. On the one hand, the two parameters moisture content and temperature determine the exposure-induced dosage that can lead to fungal infestation and subsequent decay. On the other hand, the material resistance of wood stands in opposition to exp...
L Meyer-Veltrup, C Brischke
Evaluation of surface cracks on wood – physical assessment versus subjective sensation
2017 - IRG/WP 17-20617
In the presented studies from the University of Goettingen (Study I) and the University of Hannover (Study II), the assessment of cracks with different methods and their acceptance in general as well as depending on different target groups are investigated. The aim was to determine which factors are relevant for a crack evaluation and which visual impression of a wooden surface is tolerable for co...
A Gellerich, C Brischke, L Emmerich, L Meyer-Veltrup, P Kaudewitz
Moisture performance of wood determined in laboratory and field trials
2017 - IRG/WP 17-20621
It is widely accepted that wood moisture content (MC) is the key factor when it comes to durability of wooden structures exposed to weathering. The moisture performance of wood and wood-based products has been recognized as key element in wood durability and wood protection. Actually, it should be considered as major component of the material-intrinsic resistance of wood, but never found its way i...
D Kržišnik, N Thaler, B Lesar, M Humar
Weathering protection of European hardwoods through double modification
2017 - IRG/WP 17-30715
Beech and poplar were thermally modified, treated with melamine resin and both treatments were combined. The weathering performance (cracks and general appearance) of modified beech and poplar was assessed in natural weathering and correlated to material properties such as work in bending (WB) and Brinell hardness. In addition, the equilibrium moisture content after exposure of 12 months and subse...
G Behr, A Gellerich, S Bollmus, H Militz
Evaluation of timber bridges with special consideration of detail design
2017 - IRG/WP 17-40781
Since 1997 the use of wood in bridge construction has been increasingly criticized by the Hamburg federal state authority supposedly because of shortened service life due to decay. With regard to wood research, however, it is often suggested that use of timber is suitable for weathered structures as long as constructive protection measures will be observed. In order to unravel the reasons for the ...
K Robbers, J Fromm, E Melcher
Evaluation of coating applied in treated wood: experiences in Brazil
2017 - IRG/WP 17-40814
Weathering assays study the coating degradation caused by its exposure to the action of ultraviolet radiation, winds, heat and humidity. The use of test specimens in different arrangements and exposure angles is intended to reproduce various conditions in which a product can be used. The purpose of this paper is to present the efficacy of an oil-borne varnish applied on treated wood exposed to wea...
M F Natale, J M Vidal
Assessing the nutrient value of bio-based materials in relation to early fungal growth
2017 - IRG/WP 17-20631
Bio-based materials are gaining importance in the building industry, as the focus on sustainability and life-cycle-assessment has increased dramatically over the last decade. Wood and wood-engineered products as well as insulation materials made from flax, hemp, etc. are hence increasingly used. These materials originate from renewable resources and are often biodegradable, which can cause problem...
L De Ligne, J Van den Bulcke, J Baetens, B De Baets, J Van Acker
Five-year evaluation of a field trial of Eucalyptus grandis poles treated with zinc and boron
2017 - IRG/WP 17-30721
Round Eucalyptus wood treatment in sequential stages with inorganic borates and metal salts (zinc sulfate and boric acid+borax) was studied; the aims were to form an insoluble precipitate of zinc borate inside wood and to reduce treatment costs by performing the first treatment by simple ascent and diffusion of the preservative, at the same time as it was sought to impregnate the heartwood. The se...
C Ibáñez, A Camargo, C Mantero, M Rabinovich
Evaluation of the Virulence of the Termite Species Occurring in the French Tropical Overseas Territories
2018 - IRG/WP 18-10913
The French tropical overseas territories are strongly affected by termites’ activity, which is especially devastating because the species encountered there are among the most virulent in the world. That is why in these regions it is particularly important that producers and users of wood-based products are provided with materials and preservative products whose durability and efficacy has been t...
M Kutnik, I Paulmier, J Vuillemin
Evaluation of the effect of zwitterionic buffers on termite gut protists
2018 - IRG/WP 18-10933
The thermal modification of wood is recognized as the most commercialized wood modification process. The treatment of wood at temperatures usually greater than 180 ºC results in a product with some properties enhanced (dimensional stability, durability, aesthetical colour) and some diminished (mechanical properties). The loss of mechanical strength is recognized as a limitation to the use of ther...
S Duarte, D Jones, L Nunes
Protocol of intervention against subterrranean termites in urban areas
2018 - RG/WP 18-20640
Subterranean termites are a problem of Mediterranean countries since their climatology favours their development. In Spain, termite attack is very important in cultural heritage and even in new construction, as they can cause serious damage to structural elements (pillars, beams, decks, etc.), carpentry (doors, windows, etc.) and wooden goods (furniture, paintings, libraries, etc.), causing not on...
J Galván, D Lorenzo, C Villagrá, L Robertson, R Viñambres, M T Troya
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Depictions on Wood: Acceptation and Internalization of Wood, which is an intercultural interaction tool, as “A Valuable Object” (Wood is the Material of Endless Possibilities)
2018 - IRG/WP 18-40837
Wood is a renewable and natural organic material that has a larger range of uses with inclusion of so many different places with its easy processing, functionality, versatility, anatomical structure, chemical composition, physical properties, mechanical properties, aesthetic appearance, healthy and environmentally friendly aspects, and hence there is a growing interest in making better use of wood...
I Usta
Visual appearance of unpainted wooden claddings during the first year of outdoor exposure: Evaluation of surface mould growth, lightness (L*) and wasp attack
2018 - IRG/WP 18-40841
This study addresses changes in visual appearance of unpainted wood materials exposed outdoors. Specimens of Norway spruce (Picea abies) Scots pine (Pinus sylvestris), aspen (Populus tremula), acetylated Radiata pine (Pinus radiata) and DMDHEU-modified Scots pine sapwood were exposed facing south in Ås, Norway for 60 weeks. During this period, surface mould growth development and wasp attack were...
S Karlsen Lie, L Ross Gobakken, G I Vestøl, O Høibø
Preventivephysical barriers against subterranean termites species for building protection: How to implement innovative materials to reach efficacy requirements
2018 - IRG/WP 18-40845
As the European regulation dealing with the use of biocides (BPR) for preventive protection of buildings against subterranean termites is leading to more and more pressure on physico-chemical barriers currently used (PT18), some existing developments are focusing attention on physical biocides-free barriers. The main target is then to avoid the use of active ingredients, to stay out of the BPR sco...
N Delourme-Fonseca, P Poveda, F Simon
Potential of totora and derivatives as sustainable lignocellulosic material
2019 - IRG/WP 19-40859
Totora (Schoenoplectus californicus C.A. Mey. Soják) is a macrophyte from the Cyperaceae family that grows in the Americas from California to Chile. This plant has long been used by several cultures such as the Ohlone in California, the Moche in Peru, or the Incas in Los Andes. Some communities have maintained its traditional use until the present, such as the communities living nearby Lake San P...
J F Hidalgo-Cordero, D Casado, J García, L Robertson, M T Troya
Performance of bio-based building materials – durability and moisture dynamics
2020 - IRG/WP 20-20666
When exposed to conditions favourable for decay, bio-based building materials can be susceptible to degradation. Their ability to withstand deterioration over time (performance) depends on the intrinsic or enhanced durability of the material as well as its wetting and drying behaviour. The effect of fungicidal components in wood is known since long. Other material characteristics, such as the mate...
L De Ligne, J Caes, S Omar, J Van den Bulcke, J M Baetens, B De Baets, J Van Acker