Your search resulted in 483 documents. Displaying 25 entries per page.
A summary of history and use of timber bridges in New Zealand
2017 - IRG/WP 17-40801
Wooden bridges have been an important part of road and rail networks in New Zealand. While wooden structures have largely been replaced by concrete and steel on major arteries they still have a place where lightweight, easily assembled structures are needed. These timber bridges may also be a cheaper alternative to other materials in roads which carry relatively low traffic loads. In the last ten ...
D Page, T Singh
Review on protection of timber bridges in Norway and other countries
2017 - IRG/WP 17-40809
Wood plays a major role in design and construction of modern bridges in Norway. Typical elements of those bridges are double impregnated glued laminated members, stress laminated timber decks, slotted-in steel plates, metal cladding of the surfaces of loadbearing members, and cross girders made of steel. Selected examples of timber bridges in Norway are presented. This review paper gives an overvi...
K-C Mahnert, U Hundhausen
Durability of energy efficient wooden buildings: a building physical point of view
2017 - IRG/WP 17-40812
The drive for more energy efficient and sustainable buildings resulted in an increased popularity of wooden buildings, even in countries with a masonry tradition. Often guidelines and prescriptions then are copied from other countries. Different climatic boundary conditions and tradition of finishing, though, do require different moisture tolerance criteria. This is clearly the case for water vapo...
S Roels, J Langmans
Corrosion verification experiment of the screw driven into CLT
2017 - IRG/WP 17-40816
Japan has abundant forest resources, but we depend on import for 70 percent of the consumed timber. Japan has the vision which promotes the timber self-sufficiency rate 30% to 50% by 2020. Therefore CLT attracts attention as a new timber material. Japan has a climate with high temperature and humidity, and wooden buildings are often treated with chemicals as a measure against biological deteriorat...
N Wada, H Ishiyama, S Yamamoto
Influence of sea water on timber and metal joints
2017 - IRG/WP 17-40818
In the Great East Japan Earthquake that occurred in March 2011, many buildings suffered from seawater immersion caused by the tsunami. Saito's study revealed that corrosion progresses on metal plate that experienced seawater immersion 1). However, the detailed mechanism of corrosion progresses has not yet been clarified. Therefore, in this study, salinity which is one of causes of corrosion w...
T Nishimura, H Ishiyama, F Hirose, N Wada
Markers of quality in self-bonded beech boards
2017 - IRG/WP 17-40820
A self-bonding phenomenon takes place when five layers of beech (Fagus Sylvatica L.) veneers are pressed at temperatures higher than 200ºC. If the pressing temperature between veneer surfaces reaches at least 225ºC during pressing and if the pressure applied is optimal, water-resistant bonds are formed between veneers. This study investigates the relation of thickness reduction (marker of compre...
C Cristescu, D Sandberg, O Karlsson
Testing the durability of timber products above ground using the block-test method – A critical review
2018 - IRG/WP 18-20637
The block-test method for testing the durability of wood and wood products above ground is reviewed critically with respect to practical aspects, moisture loads, corresponding decay development, and the possibilities of assessing test specimens by determining the dynamic modulus of elasticity (MOEdyn) of wood. In total, 36 blocks representing different modifications of the original set-up and a wi...
C Brischke, A Gellerich, H Militz
Thermally modified timber treated with methacrylate
2018 - IRG/WP 18-40849
Thermally modified timber (TMT) from Scots pine sapwood similar to Thermo-D quality was impregnated with methacrylate resin by the hot-and-cold method and subsequently cured at elevated temperatures. The results showed that methacrylate resin could be used to reduce colouring of painted TMT wood during accelerated weathering probably by hindering the migration of extractives. The resin itself did ...
O Karlsson, O Myronycheva, DJones, D Elustondo, D Sandberg
Determining the natural durability on xylarium samples: mini-block test, wood powder and chemical profiling
2019 - IRG/WP 19-10944
Xylaria, or wood collections, can be considered sleeping beauties in terms of wood technological and biological output. In this study we focus on determining the natural durability of xylarium specimens from the Federal Xylarium in the Royal Museum for Central Africa. The Federal Xylarium contains over 80,000 specimens, covering more than 13,000 species, mainly from Central Africa. These specimens...
V Deklerck, L De Ligne, J Van den Bulcke, E Espinoza, H Beeckman, J Van Acker
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Visual assessment of longitudinal wheel timbers and assessing the feasibility of extending wheel timber service life in the UK railway network
2019 - IRG/WP 19-20651
Timber has been a versatile building material for centuries and during the start of the Railway Age in the nineteenth century it was in considerable demand for use in the railway network, particularly bridge building. Timber is still in service and widely used throughout the UK railway network. The resilience and favourable strength to weight ratio and its relative ease of fabrication make it an...
J R Williams
Exploring the use of X-ray micro CT as a tool for the monitoring of moisture production and mass loss during lab-based fungal degradation testing
2019 - IRG/WP 19-20654
Bio-based building materials, such as wood and wood-engineered products, are susceptible to degradation by decay fungi. In-depth knowledge on the intricate material-fungus relationship as well as performance data for many bio-based building materials are still lacking, and especially knowledge on how a material’s structure and moisture properties affect the degradation process is missing. Althou...
L De Ligne, J Van den Bulcke, A De Muynck, J M Baetens, B De Baets, L Van Hoorebeke, J Van Acker
Durability classification of preservative treated and modified wood
2019 - IRG/WP 19-20659
EN 350 (2016) allows formally to determine durability classes (DC) for wood products and wood-based materials, which was previously only possible for untreated wood in the form of natural durability. In a first study, the University of Goettingen carried out the durability classification of chemically modified (modified with 1,3-dimethylol-4,5-dihydroxyethyleneurea, DMDHEU) and preservative-treate...
S Bollmus, L Bachle, C Brischke, H Militz
Development of accelerated decay test for CLT using a fungus grown on agar medium
2019 - IRG/WP 19-20664
CLT is a large-scale wooden board which consists of several layers of sawn lumber stacked in altering directions. Therefore, a lot of large cross sections appear on all narrow faces of CLT. As water penetrates easily into timber from cross section, wooden material whose cross section is exposed to water in in a usage environment is susceptible to deterioration by organisms. Wood deterioration orga...
T Miyauchi, K Kambara, W Ohmura, T Mori, H Matsunaga, N Hattori
Treatability of native and exotic alternative timber species
2019 - IRG/WP 19-40864
The service life of moderately durable species can be extended significantly if the challenge of effective treatment of refractory wood species can be overcome. Along with preservative effectiveness, the performance of preservative in treated wood depends on factors such as retention and penetration in treated wood, the wood anatomy, the uniformity of penetration and micro-distribution within the ...
D Page, T Singh
Color change of timber exposed outdoors - Influence of season exposure test starts
2019 - IRG/WP 19-40865
For the client the material and color of the exterior wall are important, because they affect the impression of the building [1]. However, discoloration of the exterior wall begins as soon as the building is completed, by various factors such as rainfall. We tried to quantitatively evaluate the changes of the exterior wood, and to organize the influences of climate conditions, in order to use the ...
K Usami, H Ishiyama
Thermal performance and fire safety properties of traditional circumferential log-cabin walls
2019 - IRG/WP 19-40872
The paper describes the experiment of fire resistance of a circumferential log-cabin wall fragment using various structural modification of the gap between two log members. The influence of the gap structural modification on the criterion of fire resistance E (envelop integrity) and I (insulation) is evaluated. The evaluating criteria are represented by the development of temperatures measured in ...
S Jochim, L Makovicka Osvaldova, M Zachar, Z Danihelova
Fungal damages in Norwegian massive timber elements – causes and measures
2019 - IRG/WP 19-40879
Massive wood elements are relatively new in Norway but the use is growing quickly, primarily the use of cross-laminated timber (CLT). Moisture performance of massive timber elements has been examined by some researchers, but more knowledge is needed. There is uncertainty regarding the need for vapour barriers or retarders in roof assemblies, and for practical reasons buildings are rarely assembled...
M S Austigard, J Mattsson
Experimental study on compressive strength performance of cross laminated timber with biodeterioration damage
2019 - IRG/WP 19-40883
The mass timber construction has attracted attention around the world. The reasons are due to the environmental impacts and the potential of the strength performance and quantity of the wood. Nowadays, CLT is one of the most important materials for the timber constructions. If we use CLT as a building material, we should consider the biodegradation risk for long time use. From an estimation of fut...
T Mori, Y Otsubo, R Inoue, M Ikeda, K Kambara, W Ohmura
Outbreak of timber pest in Philippines: A consequence of frequent typhoons
2019 - IRG/WP 19-50348
Evidence of climate change and its impact are now visible in many parts of the world. This report presents impact of natural disasters in particular typhoons on trees as it passes across the Philippines archipelago every year. Typhoons damage and destroy large number of trees which soon rot under moist and warm conditions. Wood beetles and termites find these sources very quickly, breaking down th...
P Dhang
Study on Nailed Joint with Iron Contamination. Part1: Shear Performance of Nailed Joint with Iron Contamination
2019 - IRG/WP 19-50349
In Japan, The building standard law was amended in 2000.1) The use of metal joint was obligated by this law. Since then, metal joints have been largely used for wooden buildings. Also, Act on the Promotion of Popularization of Long-life Quality Housing was enacted in 2009 and leaving Long-life Quality Housing has been focused on2). However, leaving houses to posterity for a long time causes severa...
R Nakano, D Nakano, H Ishiyama
Moisture and temperature conditions in an old, highly moisture-loaded timber building in the Røros municipality, Norway
2020 - IRG/WP 20-10966
A 150 years old log building near Røros, Norway, has been in active use as a cowshed since its erection. The animals are kept inside the cowshed all winter and this causes a situation of a high moisture load on the wooden floor, wooden walls and ceiling. Logging of temperature and humidity over one year shows that there are favourable levels of moisture in the wood and air for development of moul...
M Sand Austigard, J Mattsson
Observed and projected changes in the climate based decay hazard of timber in the United Kingdom
2020 - IRG/WP 20-20665
The risk of microbiological attack on wood is determined by both material and climatic factors and indeed the hazard for a component is based on its intrinsic durability and the conditions in which it is used. The use of wood and organic materials in construction is increasing but ultimately all these materials will be susceptible to microbiological attack. The Scheffer Climate index applies clima...
S F Curling, G A Ormondroyd
Comprehensive protection of timber in seawater
2020 - IRG/WP 20-10970
The hazard of wood in seawater can be divided into two areas: Below the water level, shipworm (Teredo navalis) and gribble (Limnoria lignorum) can attack non-resistant or insufficiently protected wood; above the water level, there is a risk by wood-destroying fungi and, to a lesser extent, insects. In a national project funded by the Deutsche Bundesstiftung Umwelt (DBU, German Federal Environmenta...
E Melcher, J Müller, T Huckfeldt
Modelling decay rates of timber exposed above ground on four different continents
2020 - IRG/WP 20-20670
Durability performance data from an international decking trial were analysed to explore relationships with climate variables, particularly those related to temperature and rainfall. Matched decking samples of slash pine (Pinus elliottii) sapwood and heartwood, spotted gum (Corymbia citriodora), Norway spruce (Picea abies) and Scots pine sapwood (Pinus sylvestris) were exposed to the weather above...
L P Francis, J J Morrell, C Brischke, P B Van Niekerk, J Norton