Your search resulted in 419 documents. Displaying 25 entries per page.
Wood properties modification by an enzymatic assisted treatment with phenolic extractives
2016 - IRG/WP 16-30696
Extractives of sawdust and bark from P. pinaster and, condensed tannins (CTs) from P. radiata bark were used to treat beech and pine veneers in combination with an oxidative enzyme, in order to stably graft such extractives onto the veneers. First, the antifungal activity of P. pinaster phenolic extractives against wood decay fungi was studied. These extractives were also used to hydrophobize pi...
D Filgueira, C Fernández-Costas, D E García, D Moldes
Enhancing wood properties through bio-based and non-biocidal co-polyesters
2016 - IRG/WP 16-40740
The commonly used wood preservation treatments are nowadays facing huge environmental issues, as well as increasing public concern. As regards those concerns, legislation tends to regulate the use of biocidal preservation chemicals.
Thus, it does appear crucial to provide alternatives to the use of biocides to allow different outdoor uses of wood such as for, posts, decking, and cladding or even ...
C L’Hostis, M-F Thévenon, E Fredon, P Gérardin
New perspectives for wood protection: enzyme-based treatments
2016 - IRG/WP 16-40742
Wood protection research is continuously looking for more benign and effective treatments. One of the main concerns deals with the toxicity of the active compounds employed in the formulations of the preservatives, since they could become a health and environmental issue. Secondly, long-lasting treatments are preferred in order to increase the service life of the treated wood. Weathering condition...
C Fernández-Costas, S Palanti, M Á Sanromán, D Moldes
Creosote leaching from timber bridges in Norway – a practical classification approach
2016 - IRG/WP 16-40744
Creosote is widely used as a wood preservative for highway timber bridges in Norway. However, excessive creosote leaching at various highway timber bridge sites leads to a bad reputation for the use of creosote treated timber constructions and the use of wood in general. Macro- and micro anatomical factors such as amount of heartwood, annual ring width, annual ring orientation, ray- height and com...
A Treu, K Zimmer
Development of a new method for wood hydrophobizing and fixation of copper compounds by chemical hardening of vegetable based modified oils
2016 - IRG/WP 16-40754
Wood products with ground and direct water contact, but without sufficient biological durability, have to be protected against biological degradation by fungi and other microorganisms. Due to European legislation (Biocidal Products Regulation 528/2012), the selection of possible chemical agents, which are still allowed to be used, is diminishing rapidly. The use of previously widely applied, very ...
C Swaboda, M Fischer, K Jacobs
A Case Study of Long-term CCA Preservative Leaching from Treated Hardwood Poles in a Humid Tropical Condition
2016 - IRG/WP 16-50324
Chromated copper arsenate (CCA)-treated Malaysian hardwoods have long been used as utility poles, posts, construction piles and motorway fencing in soil contact exposed to the threats of decay fungi and termites. Despite global concerns citing predominantly temperate conditions of long-term leaching of CCA toxic heavy metals from wood into surrounding soils and groundwater since the 1990’s, the ...
A H H Wong, W S M Chin
Interactions between fungal glutathione transferases and wood extractives
2017 - IRG/WP 17-10894
The interactions between extractives from several tree species of French Guyana and glutathione transferases (GST) from the white-rot Trametes versicolor have been studied. These interactions have been monitored using a thermal shift assay. It appears from these experiments that TvGSTO2S interacts strongly with acetonic extract of Bagassa guianensis and in particular with oxyresveratrol. In agreem...
T Perrot, F Saiag, N Amusant, S Dumarçay, P Gérardin, M Morel-Rouhier, R SormaniI, E Gelhaye
Rapid detection of the Alaska yellow cedar, Callitropsis nootkatensis (Cupressaceae) extractives using Fourier transform infrared (FT-IR) spectroscopy
2017 - IRG/WP 17-20612
Global changes in wood harvesting towards plantation species grown on much shorter rotations has the potential to markedly alter wood quality perceptions. Nowhere is this more risky than with naturally durable species where there is compelling evidence that faster grown woods tend to be less durable. The ability to non-destructively assess durability may allow growers to identify materials that re...
S Lipeh, J J Morrell
Efficacy of Erythropleum suaveolens (potrodom) and Distemonanthus benthamianus (bonsamdua) water extractives on the durability of five Ghanaian less used timber species of varying perviousness and retentiveness
2017 - IRG/WP 17-30705
Conventional wood preservatives are not only toxic to target bio-deterioration organisms but also to humans, other organisms and the environment. In an effort to find preservatives that are less toxic or non-toxic to man, other organisms and the environment, efficacy of branch bark and heartwood water extracts (0.65 g/ml) of Erythropleum suaveolens (potrodom) and Distemonanthus benthamianus (bonsa...
A Asamoah, K Frimpong-Mensah, C Antwi-Boasiako
The Protective Effect of Different Tree Bark Extractives against Decay Fungi
2017 - IRG/WP 17-30707
There are various modification methods which increase the resistance of wooden materials. Due to recent environmental regulations, there is a need for new and environmentally-friendly wood preservatives. In this study, six different tree bark extractives were evaluated for their wood resistance against fungal degradation. For this purpose, the white rot fungi (Tramates versicolour) and brown rot f...
Ö Özgenç, S Durmaz
Review of Leaching Experiments of CCA-Treated Wood and Wood Treated with Copper-based Alternatives
2017 - IRG/WP 17-50330
The objective of this study was to compare leaching rates of various wood preservatives from treated wood and the tests used to gather this information. The preservatives compared included CCA and the copper-based alternatives, MCQ, ACQ, and MCA. The tests compared included AWPA E11, SPLP, TCLP, and environmental leaching tests. Among all of the tests evaluated, environmental tests most closely si...
A Jones, J Marini, H Solo-Gabriele
Uncertainty in life cycle assessment of preservative treated wood – copper and freshwater ecotoxicity
2017 - IRG/WP 17-50331
Life cycle assessment (LCA) is a method for quantifying the environmental impacts of a product over the life cycle. In the last years, there have been a growing application of LCA in developments of environmental product declaration (EPD), which is utilised by professional procurement of materials for buildings. For legislative issues, LCA have also been used to assess application of creosote to t...
L G F Tellnes
Multivariate modeling of mould growth in relation to extractives in dried Scots pine sapwood
2017 - IRG/WP 17-20629
Influence of extractives on mould growth on Scots pine sapwood dried in air or in kiln was studied. Boards were sprayed with water mixtures of spores of the fungal species Penicillium sp., Aspergillus sp., Mucor sp., Paecilomyces sp., Trichoderma sp., treated at a temperature of 22ºC at 90% RH, classified into a percentage of covered area. Acetone and water extracts were isolated and analyzed for...
O Karlsson, O Myronycheva, M Sehlstedt-Persson, M Öhman, D Sandberg
Natural durability, ethanol-toluene extractives and phenol content prediction of eight wood species from Madagascar using NIRS multispecific models
2018 - IRG/WP 18-10926
Madagascar has nearly 4000 species of trees and shrubs, but wood properties of only 200 species have been studied. Some properties, such as the natural durability or chemical composition are of importance for adequate and optimal use of these timber species. Since durability tests take long time and chemical analyzes can be very expensive, alternative methods such as near infrared spectroscopy (NI...
A R Razafimahatratra, H Rakotovololonalimanana, M-F Thévenon, C Belloncle, G Chaix, T Ramananantoandro
Study of the effect of extractives on the natural durability of Eucalyptus bosistoana wood
2018 - IRG/WP 18-10928
Wood as a natural material is degradable both by biotic deterioration agents (fungi, bacteria, marine borers, insects) and abiotic (UV and IR radiation, moisture, fire, etc.). The inherent resistance to the attack of the deteriorating agents is defined as the natural durability of the wood. This is an important property when considering the shelf life of wood products exposed to extreme conditions...
M Ibáñez, C Mantero, N Silva, F Resquín
Effects of wood protecting biofinish and linseed oil on fire behaviour and leachability of the fire retardant
2018 - IRG/WP 18-30728
A wood protecting biofinish is based on a protective and decorative fungal-based coating and a linseed oil impregnation (called Xyhlo biofinish). This biofinish enables the long-term use of wood in outdoor applications without using toxic chemicals.
The fire resistant properties of materials used in buildings are very important. Since Xyhlo biofinish is relatively new, only little information is ...
S Rensink, E J van Niewenhuijzen, M F Sailer
Selection of heat flux value for wood fire retardants testing using MLC
2018 - IRG/WP 18-40846
One of more crucial elements of investigating treated wood combustion properties with the use of a cone calorimeter is a proper selection of heat flux (HF). The HF level is directly reflected in time to ignition and a thermal degradation degree. The ignition of raw wood or of wood ineffectively protected against fire occurs at a low HF level, i.e. 10-20 kW/m2. By contrast, the ignition of wood whi...
B Mazela, W Perdoch, W Grześkowiak, A Batista
Thermally modified timber treated with methacrylate
2018 - IRG/WP 18-40849
Thermally modified timber (TMT) from Scots pine sapwood similar to Thermo-D quality was impregnated with methacrylate resin by the hot-and-cold method and subsequently cured at elevated temperatures. The results showed that methacrylate resin could be used to reduce colouring of painted TMT wood during accelerated weathering probably by hindering the migration of extractives. The resin itself did ...
O Karlsson, O Myronycheva, DJones, D Elustondo, D Sandberg
Influence of different triazoles as co-biocides in wood preservatives on efficacy and the environmental impact
2018 - IRG/WP 18-50333
In this study we investigated the efficacy and impact on the environment of different co-biocide triazoles in wood preservatives. Four different formulations (all containing 9.5% Copper) contained individual and combinations of cyproconazole, tebuconazole, propiconazole as co-biocides. Four formulations were tested according to EN 113 and EN 84 (ageing) to determine the brv for each formulation. T...
M Klamer, T Jensen, S Bang-Achton, E Morsing
Declaring life cycle inventory of toxicity related emissions in environmental product declarations of preservative treated wood products
2018 - IRG/WP 18-50339
Life cycle assessment (LCA) including impacts on toxicity for preservative treated wood has been shown to have large uncertainties. With the growing demand for verified LCA in environmental product declarations (EPD), the need for reliable data is crucial for realistic assessment of wood products. Uncertainty is caused by several issues such as service life prediction, leaching rates and calculati...
L G F Tellnes, C Askham, P-O Flæte, M Klamer
Effects of teak, Tectona grandis Linn, heartwood extractives against Heterotermes indicola (Isoptera; Rhinotermitidae)
2018 - IRG/WP 18-10910
Heartwood extractives from Tectona grandis were investigated for antitermitic activities against Heterotermes indicola in laboratory experiments. Extractives were removed from wood shavings by soxhlet extraction using an ethanol: toluene (2:1) solvent system. Termite feeding and mortality followed a concentration dependent response. The highest termite mortality occurred at an extractive concentra...
B Hassan, S Ahmed, M Mankowski, G Kirker, R E Ibach, M Misbah ul Haq
Natural durability of four Tunisian Eucalyptus wood species and their respective compositions in extractives
2019 - IRG/WP 19-10942
In the 50’s, Tunisia government introduced more than 11 Eucalyptus wood species. Eucalyptus species were planted in Tunisia in different arboreta throughout the country for close observation and adaptation to climate and soil. These fast-growing wood species were mainly used as fire wood, for the production of mine wood and to fight against the erosion. These tree species were adapted themselve...
S Ben Ayed, M T Elaieb, S Dumarçay, B De Freitas Homen De Faria, M-F Thévenon, P Gerardin, K Candelier
Effectiveness of Gleditsia triacanthos heartwood extractives as wood protector
2019 - IRG/WP 19-10950
In Uruguay, Gleditsia triacanthos (known as honey locust) is an exotic tree species categorized as invasive; it produces severe ecological impact as it displaces native species, causing changes in the structure of the native forest community. Being extremely difficult to control, it is widely distributed through Uruguay and neighbouring countries. However, one way to mitigate its negative impact i...
C M Ibanez, C Mantero, P Raimonda, X Pintos, E Pereira
Identification of Antifungal Compounds in Konjac Flying Powder and Assessment against Wood Decay Fungi
2019 - IRG/WP 19-30737
The antifungal activity of konjac (Amorphophallus rivieri) flying powder (a by-product produced during mechanical processing of konjac flour) ethanol extract was evaluated against wood decay fungi in culture. Compounds associated with antifungal activity in the extracts were isolated and purified by silica gel column chromatography. The antifungal active fractions were identified by ultra-high-per...
Z Bi, F Yang, Y Lei, J J Morrell, L Yan
Improvement of wood decay and termite durability resulting from combined treatments based on borax/phenol-formaldehyde impregnation followed by thermal modification
2019 - IRG/WP 19-40871
This study determined the factors influencing the boron content after leaching of pine blocks impregnated with aqueous solution of phenol-formaldehyde (PF) resin with or without borax and subjected to heat treatment by response surface methodology. An experimental design permits to analyze the effects of heat treatment temperature (150, 185 and 220°C), curing time (5, 12, 5 and 20 hours), resin c...
S Salman, M-F Thevenon, A Petrissans, S Dumarcay, P Gerardin