Your search resulted in 3175 documents. Displaying 25 entries per page.
Monitoring of wood biodeterioration by infrared spectroscopy
2017 - IRG/WP 17-20607
The susceptibility of wood to deterioration by rotting fungi is intrinsically related to its chemical composition and the environmental conditions at its place of use, and if not detected in time, can cause enormous financial losses. The process of wood biodeterioration by decay fungi can be evaluated through laboratory accelerated test, in specific field tests, or through non-destructive techniqu...
E Meneses Oliveira, A Florian da Costa, J W Batista Braga
Consistency of performance of acetylated wood
2017 - IRG/WP 17-20608
It is well known that acetylation of wood improves the resistance against wood decaying fungi and insects, as well as its dimensional stability under varying moisture conditions. Accsys Group continues to support a variety of laboratory and field studies around the world to assess and monitor the durability, dimensional stability and uniformity of its products. To gain and maintain market acceptan...
F Bongers, J van Zetten
Three-Dimensional Digital Image Correlation of Strains in Profiled Wood Decking Exposed to Wetting & Drying
2017 - IRG/WP 17-20611
We use three dimensional digital image correlation to measure the strains that develop at the surface of profiled radiata pine (Pinus radiata D. Don) deck boards subjected to a wetting and drying cycle. We hypothesise that surface profiling will change the pattern of strain distribution at the surface of deck boards by concentrating stresses at the base of profile grooves. Five groups of three deck board samples were produced from five different pieces of machine stress-graded radiata pine wood. Two wavy profiles, ribble or ripple, were tested. Flat unprofiled boards acted a control. Each board was fixed to a rigid frame and subjected to a wetting and drying cycle. Full field surface strain data was collected using 3D digital image correlation. Strains varied across the surface of both flat and profiled boards. Profiling changed surface strain patterns; strain maxima and minima developed in the profile ridges and grooves during wetting, respectively, but this pattern of strains reversed during drying. Such a pronounced reversal of strains was not observed when flat boards were exposed to wetting and drying, although there was a shift towards negative strains when flat boards were dried. We conclude that profiling changes surface strain distribution in deck boards exposed to wetting and drying, and causes high strains to develop in the grooves of profiled boards. These findings help explain why checks in profiled deck boards are mainly confined to profile grooves where they are difficult to see, and the success of profiling at reducing the negative effects of checking on the appearance of wood decking.
J Mallet, S Kalyanasundaram, P D Evansa
Modelling of moisture content in timber bridge details
2017 - IRG/WP 17-20613
The design of details is an important aspect in durability design of timber bridges. Details are often considered the weakest points in bridges due to their tendency to trap and accumulate moisture and thus facilitate decay. When designing maintenance plans and inspection intervals, it is important to know how design choices will come to influence the service life. Moreover, service life and wood ...
J Niklewski, C Brischke, E Frühwald Hansson, L Meyer-Veltrup
Monitoring Diversity and Colonization Patterns of Wood-Inhabiting Fungi Using Field Stake Tests
2017 - IRG/WP 17-20614
Advances in molecular identification of microbial communities enabling rapid microorganism determination have allowed ecological data to be increasingly incorporated into standardized wood performance tests. Combining standard field tests with molecular methods to study wood-associated microflora can help to better understand fungal colonization and decay processes of wood in service. The potentia...
P Torres-Andrade, J Cappellazzi, J J Morrell
Overview of the treated wood quality control program in the United States with the recent challenges and advances
2017 - IRG/WP 17-20616
In the past two decades, there have been significant and rapid changes in wood protection technologies for residential applications which have moved away from long established heavy duty metal oxide based products such as chromated copper arsenate (CCA). The successor generation of wood protection systems usually contain copper as the primary biocide, in combination with carbon-based co-biocides s...
L Jin
Evaluation of surface cracks on wood – physical assessment versus subjective sensation
2017 - IRG/WP 17-20617
In the presented studies from the University of Goettingen (Study I) and the University of Hannover (Study II), the assessment of cracks with different methods and their acceptance in general as well as depending on different target groups are investigated. The aim was to determine which factors are relevant for a crack evaluation and which visual impression of a wooden surface is tolerable for co...
A Gellerich, C Brischke, L Emmerich, L Meyer-Veltrup, P Kaudewitz
Moisture content as a quality control parameter in thermally modified timber production
2017 - IRG/WP 17-20622
Quality assurance (QA) or factory production control (FPC) is necessary to ensure a proper production process. The requirements of QA/FPC can result from EN and national standards, quality assurance systems, or producer-specific rules.
TMT producers must ensure that the process was correct, and to ensure traceability of products. In addition to the electronic records, the material should be che...
W Scheiding, H Turkulin, S Stein
An experimental study of mould growth and wood decay in timber frame walls
2017 - IRG/WP 17-20623
This paper deals with parameters related to the occurrence of mould growth and wood decay in timber frame walls. In a first part, the hygrothermal conditions inside a timber frame wall finished with brick veneer cladding are analysed to get an idea of possible moisture related problems. It is shown that, based on the VTT mould prediction model, there is a mould risk on the interface between the in...
M Vanpachtenbeke, J Van den Bulcke, I De Windt, J Langmans, S Roels, J Van Acker
New Standards for Approval of Modified Wood within the Nordic Wood Preservation Council (NWPC)
2017 - IRG/WP 17-20624
In the Nordic countries, there is a long tradition for quality labelling of preservative treated wood. Until now the labelling has been restricted to pine and other easy to treat wood species, but with the introduction of a new set of standards it is now possible to obtain the Nordic Wood Preservation Council’s (NWPC) quality labelling also for modified wood.
In this paper, we will introduce th...
N Morsing, E Engelund Thybring, M Klamer
Ensuring Quality of Treated Wood – Regulations, Certifications and Associative Background in the Field of Wood Protection in Europe
2017 - IRG/WP 17-20626
Beside legal requirements, buyers and end-users of wood preservatives and/or of treated wood and wood-based materials may require additional warranties regarding the quality and the performance of the products available on the market. These greatly enhance the confidence of end-users and the chance for a product of being marketed with a quality label. Additionally, quality control systems and trai...
M Kutnik, M Klamer, E Melcher
Guidance on the European Biocidal Products Regulation Concerning Efficacy of Wood Preservatives
2017 - IRG/WP 17-20627
In Europe wood preservatives belong to Product Type 8 (PT8) of the Biocidal Products Regulation (BPR, EU n. 528/2012), which regulates the authorisation of biocidal active substances and products in the European market.
The applicant, who aims to obtain authorization to place a product onto the European market, needs to submit data to substantiate the label claims for the intended uses. Label cla...
I Stephan, M Kutnik, E Conti, M Klamer, L Nunes, J Van Acker, R Plarre
Development of Potentiometric Enzyme Biosensor for Detection of Permethrin Preservative in Treated Wood
2017 - IRG/WP 17-20628
Characteristics of a potentiometric enzymatic biosensor based on a pH transducer for permethrin detection in treated wood are reported in this article. The transducer contained a plasticiser-free methacrylic-acrylic membrane immobilised with hydrogen ionophore and a lipophilic salt. A poly(2-hydroxyethyl methacrylate) (pHEMA) was used to immobilise carboxylesterase for the detection of permethrin....
M Nasir Mat Arip, C Tan, Gan Kee Seng
Activity of Two Strobilurin Fungicides Against Three Species of Decay Fungi in Agar Plate Tests
2017 - IRG/WP 17-30704
The objective of this study was to examine the toxicity of strobilurin fungicides against wood decay fungi in order to assess their potential to act as a co-biocide for copper-based wood protection. Two strobilurin fungicides, Heritage (50% azoxystrobin active ingredient) and Insignia (20% pyraclostrobin active ingredients), and copper sulfate pentahydrate were tested against one white rot fungus...
J D Tang, T Ciaramitaro, M Tomaso-Peterson, S V Diehl
Anti-fungal activity of rutin and rutin-metal complexes as wood protectants
2017 - IRG/WP 17-30708
The anti-fungal activity of Rutin, a flavonoid, alone or complexed with copper or zinc was investigated in a petri dish test with Gloeophyllum trabeum and Trametes versicolor as the test fungi. Rutin and the Rutin-metal complexes showed significant inhibition against each fungus. Rutin-Cu and Rutin-Zn strongly inhibited the brown rot fungus, G. trabeum, while Rutin and Rutin-Zn inhibited T. versic...
Li Yan, J J Morrell, Jie Zhong, Xiuzhu Mao
Copolymers of tannin extracts as wood protection agents
2017 - IRG/WP 17-30709
Wouldn´t be a dream to preserve wood with the substances which the nature already synthesizes for protecting itself? The idea we would like to pursue is simple: Increase the concentration of these substances, the tannins, trying to fix them properly in wood. It appears easy but it is not. Sensibility against leaching, fungal decay and weathering were observed. In this paper new flavonoid co-polym...
G Tondi, L Sommerauer, A Oberle, A Petutschnigg, M-F Thevenon
Liquefaction of woody waste: A novel approach in wood protection from CNSL based liquefied wood polyols
2017 - IRG/WP 17-30711
Liquefaction of lingo-cellulosic biomass is one of the thermo-chemical conversion processes for developing new materials, adhesives, preservatives and energy systems. The process also provides an opportunity to utilize waste wood such as saw-dust, woody wastes, branches and twigs for the development of value added products. Thus, this research paper deals with an investigation of antifungal and a...
A Kumar, G B.Nagarajappa, S Singh Chauhan
Possibility of using lichen (Usnea filipendula) and mistletoe (Viscum album L.) extracts as potential natural wood preservative
2017 - IRG/WP 17-30712
Increasing environmental pressures on toxic chemical wood preservatives lead to the development of natural and environmentally friendly wood preservatives. In this study, using possibilities of lichen (Usnea filipendula) and leaves of mistletoe (Viscum album L.) as potential natural wood preservative were researched. Treatment solutions have been prepared with two different solvents, water and met...
Ü C Yildiz, C Kiliç, A Gürgen, S Yildiz
Bio-friendly wood protection systems - resistance to mould and blue-stain fungi
2017 - IRG/WP 17-30713
With stricter restrictions on the use of biocides and increasing environmental awareness there is a pronounced need for effective bio-friendly protection systems in the wood preservative and wood coating industry. One of the possible pathways is to exploit and utilize natural substances with active biological effects. Silanes, caffeine, natural oils and potassium carbonate were chosen as compounds...
L Ross Gobakken, W Perdoch, B Mazela, P Kwaśniewska-Sip, G Cofta
Decay Resistance of Scotch pine Wood Impregnated with Agaricus campestris Bio-Protective Extract
2017 - IRG/WP 17-30714
In this study it was investigated that the possibilities of the use of fungal extract as wood protection solution against wood destroying fungus. For that purpose; the decay resistance of Scotch pine wood samples, impregnated with Agaricus campestris (field mushroom) fungal extract, was examined against the brown rot fungi “Coniophora puteana”. Impregnation procedure was applied in accordance ...
S Yildiz, Ü C Yildiz, A Yilmaz
Thermal stability of a wood protective biofinish and the influence of flame retardants on Aureobasidium cells
2017 - IRG/WP 17-30716
In general there is an increasing need for sustainable resources, including sustainable building materials. Wood is one of these sustainable resources and is more used as an outdoor building material. Since unprotected wood will usually be degraded during outdoor exposure, many different protection systems are available on the market. Protection systems containing biocides however might create obs...
S Rensink, E A M Klein Rot, M F Sailer
Effects of heat treatment on sound absorption coefficients in nanosilver-impregnated and normal solid woods
2017 - IRG/WP 17-40770
Effects of impregnation with silver nano-suspension as well as heat-treatment on sound absorption coefficients (AC) were studied in tangential direction of five different solid woods based on their importance. AC was measured at two frequencies of 250 and 500 Hz. A 400 ppm nanosuspension was used for the impregnation; silver nanoparticles had a size range of 30-80 nm. Based on the obtained results...
A Esmailpour, J Norton, H R Taghiyari, H Zolfaghari, S Asadi
Effects of Nano-Wollastonite Impregnation on Fire Properties of Some Thermally-Treated Solid Wood Species
2017 - IRG/WP 17-40771
The effects of nano-wollastonite (NW) suspension impregnation on the fire-retarding properties of heat-treated solid wood of three species (beech, poplar, fir) were studied. Heat treatment was performed at two temperatures of 180 °C and 200 °C. Impregnation was carried out at a pressure of 3 bars for 30 min. The fire properties included ignition time, glowing time, back-darkening, back-splitting...
H R Taghiyari, R Hossinpourpia, S Adamopoulos, A Jahangiri, D Rabie
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Permeability of Eucalyptus wood improved by microwave treatment
2017 - IRG/WP 17-40773
The wood species with low permeability may cause many problems during timber manufacturing. Extreme difficulties take place in fabricating new wood-based composites by impregnating low- permeability timber with functional materials, such as flame retardant, preservatives and resins. Microwave (MW) treatment can increase the permeability of wood both in transverse and longitudinal directions. The e...
Xia He, Xianjun Li, Jie Xie, Xingyang Xiong