Your search resulted in 306 documents. Displaying 25 entries per page.
Suppression of termite feeding by Sudan red 7B
1988 - IRG/WP 1344
Groups of the Formosan subterranean termite, Coptotermes formosanus Shiraki, were fed for 14 days on wood shavings soaked in acetone solutions of one of three concentrations (0, 0.5, or 1%) of the dye, Sudan Red 7B. Groups of marked or unmarked termites were then placed in containers and allowed to feed on undyed wood for 21 days. Dyed termites had lower wood feeding rate, survivorship, and number...
K S Delaplane, L A Bourg, J P La Fage
Penetration of oil-borne preservatives in American elm
1975 - IRG/WP 355
Pressure treatment of elm posts and cants by Rueping schedules resulted in erratic penetration. Instead of the expected gradual decrease in retention from surface inward in posts, inner zones frequently contained more preservative than the surface quarter inch. Heartwood was found penetrated when sapwood was not. There were numerous skips in treated zones. The prevalence and possible causes were i...
E A Behr
Production of fungal protoplasts from selected wood-degrading fungi
1991 - IRG/WP 1500
Studies of hyphal morphology and the effects of various chemicals on growth are often difficult to perform on filamentous fungi because of the difficulty of observing the protoplasm through the rigid hyphae wall and because most activity occurs in a limited region near the hyphal tip. As an alternative, hyphae can be reacted with certain cell wall degrading enzymes to remove the cell wall to produ...
C Rui, J J Morrell
A comparison analysis of eight strains of Serpula lacrymans (Schum. ex Fr.) S.F. Gray
1991 - IRG/WP 2362
Investigations were previously carried out to compare eight strains of Serpula lacrymans (Schum. ex Fr.) S.F. Gray (some used in various countries as standard test strains): FPRL 12C (England), FPRL 12E (Germany), Warsaw III (Poland), HFP 7802 (Japan), DFP 16508, 16509, 16521 and 16522 (Australia). Studies included growth rate and dry mass of mycelium, decay capacity, reduction of compression stre...
J Wazny, J D Thornton
Extracellular laccase production in brown-rot fungus Coniophora puteana
2001 - IRG/WP 01-10391
Coniophora puteana, one of representing brown-rot fungus, was investigated in terms of extracellular ligninolytic enzyme production. Three fungal strains of C. puteana were inoculated in liquid culture medium with sawdust of pine and oak wood. Extracellular laccase production was observed in some strains of C. puteana in the culture medium with sawdust of oak wood. The highest activity occurred at...
Kwang-Ho Lee, Seung-Gon Wi, Yoon Soo Kim
Comparison of bluestain fungi growing in vitro and in vivo
1996 - IRG/WP 96-10149
Both moulds and bluestain fungi cause serious economic losses for forestry and timber processing industries and much research is aimed at finding environmentally and economically acceptable methods of control. It is especially important to study the growth of these fungi in freshly cut wood, which has been unaltered by drying or sterilisation, and which therefore resembles the substratum they woul...
A Uzunovic, J F Webber, D J Dickinson
Wood preservation in Uruguay
1987 - IRG/WP 3404
The purpose of this paper is a brief description of the current status of wood treatment in Uruguay. The forest resources of the country are summarized, the environment, their economic importance and future potential. The present wood treating facilities are described, together with the chemicals used and the standards generally accepted. Wood treated products used in the Uruguayan market are cite...
G Baillod
Production of monoclonal antibodies to fungal metabolites
1986 - IRG/WP 1306
The role of fungal extracellular enzymes in wood biodegradation is incompletely understood. Our lab is beginning a project utilizing monoclonal antibodies to characterize extracellular metabolites of the brown rot fungus Poria placenta Fr. (Cooke). Monoclonal antibody technology takes advantage of the ability of antibody secreting spleen cells from immunized mice to fuse in the presence of polyeth...
J Jellison, B Goodell
Influence of the nutritional elements on pigmentation and production of biomass of bluestain fungus Aureobasidium pullulans
1997 - IRG/WP 97-10198
The effect of the carbon source and the amount of the nitrogen on the melanization and the production of mycelial mass of bluestain fungus Aureobasidium pullulans was studied by using solid state cultivations. The carbon sources used varied from easily soluble sugars to structural polysaccharides existing in lignocellulosic material. The amount of melanin was evaluated by using partial purificatio...
A-C Ritschkoff, M Rättö, F Thomassin
Wood preservation in Italy
1985 - IRG/WP 3354
The report summarizes the history of wood preservation in Italy up to the present time. Information on the Italian climate and the main hazards to timber are dealt with and the amounts of timber grown and imported and exported tabulated. The main commodities treated are poles and sleepers. The amounts of preservative used have been estimated and details listed of the 10 pressure plants in the coun...
A Gambetta, E Orlandi, R Cockcroft
Blue Staining of Coated Modified and Unmodified Wood
2006 - IRG/WP 06-10589
We investigated resistance of unmodified, DMDHEU modified and oil heat treated uncoated and coated Scots pine wood against blue stain fungi. Both EN 152-1 and the reverse exposure tests showed excellent resistance of DMDHEU and especially of oil heat treated wood against blue staining. It is not needed to add any additional protective coating layers to prevent modified wood from staining. However,...
M Petric, M Pavlic, M Humar, M Tomažic
Effects of two insect growth regulators (IRGs) on Microcerotermes diversus (Silvestri) (Isoptera: Termitidae) in Southwest Iran
2006 - IRGWP 06-10601
Microcerotermes diversus (Silvestri) is the most economically damaging termite species in structures in southwest, Iran. One safe control strategy that may reduce the subterranean termite damage in buildings is the use of IGRs in a suitable bait matrix. The effects of two juvenile hormone analogues, Admiral (Pyriproxyfen ) and Farox on M. diversus were evaluated over a range of concentrations ( 10...
B Habibpour, M S Mossadegh, G Henderson, S Moharramipour
Termite Response to Oil-Heat-Treated Norway spruce, Scots Pine and Eucalyptus Wood
2006 - IRG/WP 06-20325
The work here presented focused on the behaviour of subterranean termites (Reticulitermes grassei Clément) towards Oil-Heat-Treated (OHT) Norway spruce (Picea abies L.), Scots pine (Pinus sylvestris L.) and eucalyptus (Eucalyptus globulus Labill) wood, with a particular interest in the development of simple methods adequate to study the resistence of these materials to termite attack. Small test ...
L Nunes, T Nobre, C Welzbacher, A O Rapp
Identification of fungi colonising coated and modified wood exposed outdoors using sequencing and T-RFLP profiling
2006 - IRG/WP 06-20326
Wood decay and staining fungi are known to colonize coated and modified wood. Rapid and reliable ways of identifying fungi on coated and modified wood may improve diagnostics and product development. In this work nine fungi growing in painted wood panels exposed outdoors at a test field in Uppsala, Sweden, were identified using sequencing and T-RFLP (Terminal Restriction Fragment Length Polymorphi...
U Råberg, J Bijelovic, C J Land, S Bardage, N Terziev
Heat treatment of less-valuable Nigerian-grown Ceiba pentandra wood for improved properties
2006 - IRG/WP 06-40332
The hardwood Ceiba pentandra locally known as “ araba “ in Nigeria is rarely used for structural and construction works due to its high dimensional instability, low strength and durability values. Samples (10 x 10 x 150mm) were removed from four green boards (25 x 200 x 3000mm) of this species originating from a natural forest stand in Nigeria and subjected to 2-hour heat treatment at 160°C a...
L Awoyemi
Improvement of Grevillea robusta durability using heat treatment
2006 - IRG/WP 06-40333
Heat treatment of Grevillea robusta was carried-out under inert conditions to improve its durability. Resistance of heat treated samples was evaluated by malt agar block tests after three months of exposure to several wood rotting fungi. Results showed that the fungal durability was greatly improved after treatment. There was a good correlation between fungal resistance and mass loss which is a fa...
F Mburu, S Dumarçay, F Huber, M Petrissans, P Gérardin
Wood plastic composites from modified wood; Part 1 - Conceptual idea, mechanical and physical properties
2006 - IRG/WP 06-40338
Wood plastic composites, WPCs, are rapidly taking shares from preservative treated wood on the decking market. However, the long term performance of the WPC products in this application is uncertain. Therefore, in an attempt to increase the long term performance and durability, the substitution of the unmodified wood component with modified wood has been studied in the work presented in this paper...
P Larsson Brelid, B K Segerholm, M Westin, M E P Wålinder
The Effect of Flavonoids on Colour and Spectral Changes of the Wood Surface Caused by Heat Treatment or Ultra-violet Irradiation
2006 - IRG/WP 06-40341
Both heat treatment and UV irradiation can cause discolouration and change in the spectral properties of wood surface. Some of the characteristic flavonols have significant role on colour and spectral changes, despite of their relative small quantities in wood.
Colour changes and spectral properties of natural and extracted black locust (Robinia pseudoacacia L.) and poplar (Populus nigra L.) were...
R Csonka-Rákosa, L Molnár-Hamvas, E Börcsök, J Molnár, K Németh
Assessment of the Envelope Effect of Three Hot Oil Treatments: Resistance to Decay by Coniophora puteana and Postia placenta
2006 - IRG/WP 06-40344
Timber of Corsican pine (Pinus nigra var. maritima) and Norway spruce (Picea abies) was treated in hot linseed oil, rapeseed oil and a proprietary resin derived from linseed oil. The samples were immersed in oil or resin under reduced pressure at temperatures of 180°C and 200°C. Very high uptakes of the oils or resin were recorded for pine, while spruce showed lower weight percent gains, below...
M J Spear, C A S Hill, S F Curling, D Jones, M D C Hale
Wood plastic composites from modified wood. Part 2 - Durability in laboratory decay tests
2006 - IRG/WP 06-40353
The decay resistance of wood plastic composites, WPCs, was tested according to modified versions of AWPA E10 (soil-block test) and ENV 807 (tests in three un-sterile soils, terrestrial microcosms, TMCs). The WPC materials were conically extruded profiles with 30% polypropylene content. The 70% wood content was untreated Scots pine sapwood, acetylated pine and heat treated Norway spruce, respective...
M Westin, P Larsson Brelid, M L Edlund, G Alfredsen
Effects of heat treatments on decay resistance and material properties of ponderosa pine and yellow poplar
2007 - IRG/WP 07-40374
The potential for using heat treatment to improve the properties of North American fenestration species was evaluated on ponderosa pine (Pinus ponderosa L) and yellow poplar (Liriodendron tulipifera L) treated using the ThermoWood process at various treatment temperatures and times. Soil block tests using Gloeophyllum trabeum, Postia placenta, or Trametes versicolor showed that durability was enh...
C Vidrine, C Freitag, J Nicholson, J J Morrell
Copper fixation in ACQ-D treated Chinese fir at various temperature and relative humidity conditions
2007 - IRG/WP 07-30436
In this study, the effect of different conditions of temperature, relative humidity, and duration of post-treatments on accelerating copper fixation in ACQ-D treated Chinese fir wood blocks was investigated. The conditions include the combination of three temperatures (21, 50, and 70?) and two relative humidity levels (20% and 80%), also include four temperatures (50, 70, 90, and 110?) without con...
Jinzhen Cao, Lili Yu
Natural Weathering of Coated Oil Heat Treated Wood
2007 - IRG/WP 07-30440
Oil heat-treated (thermally modified) pine wood was coated with 9 different types of solvent- or water-borne exterior finishes. The systems with modified wood substrate as well as unpainted and painted non-modified controls were exposed to weathering (EN 927-3) on two locations with sub-alpine and alpine climate. The influence of natural ageing on surface systems was evaluated after one year of ex...
M Petric, B Kricej, M Pavlic, A Rapp
Mold resistance of heat-treated wood
2007 - IRG/WP 07-40358
The resistance of heat-treated sugi sapwood against three mold fungi was evaluated. Wood specimens were first subjected to heat treatments at 180 and 220ºC for 2 and 4 hours. Mold growth on the surface of the specimens was measured 1, 2, 4 and 6 weeks after the inoculation with the fungi in laboratory conditions. Laboratory decay tests were performed using two brown and white-rot fungi along with...
S N Kartal
Multivariate analysis of infrared spectra for the prediction of the mechanical performance and dimensional stability of thermally modified wood
2007 - IRG/WP 07-40367
The use of calibrated mid-infrared Fourier transform (FTIR) spectroscopy for predicting the main bending strength parameters of thermally modified wood is described for the first time. The analysis is based on the handling of OSC-filtered FTIR data from control and treated wood samples, using partial least squares (PLS) regression.
Sets of Norway spruce, Scots pine and Beech wood samples were th...
M M González-Peña, M D C Hale