Your search resulted in 662 documents. Displaying 25 entries per page.
The influence of chemical and thermal modification on homogeneity between sapwood, heartwood, and transition wood of short rotation teak
2023 - IRG/WP 23-40961
Short rotation teak wood has low quality especially in durability. Heartwood presents sufficient natural durability and poor impregnability; meanwhile, most sapwood requires special treatment to increase its durability. The objective of this work was to investigate the effect of thermal or chemical treatment on homogenization between sapwood, heartwood, and transition wood for some selected proper...
R Martha, B George, W Darmawan, P Gerardin
Evaluation of the efficacy of silver nanoparticles and chitosan oligomer composites as poplar wood protective treatments against termites
2023 - IRG/WP 23-40963
Populus × euramericana ‘I-214’ (poplar) is a fast-growing species widely distributed throughout the world, and in the Castile-Leon region of Spain it accounts for more than 50% of all plantations. Its wood is becoming increasingly appreciated, yet its low durability against xylophagous agents —termites being one of the most aggressive and destructive in warm climates— continues to be a li...
E Spavento, M T Troya, M Casado-Sanz, J Martín-Gil, P Matín-Ramos, L Robertson, L Acuña-Rello
Adhesion and performance of exterior wood coatings on chemically and thermally modified wood – Results from 5.5 years outdoor exposure
2023 - IRG/WP 23-40964
Non-durable softwood and hardwood species were treated with the water-soluble cyclic N-methylol compounds 1,3-dimethylol-4,5-dihydroxyethyleneurea (DMDHEU) and methylated DMDHEU. One half of the modified specimens were coated with a waterborne acrylic coating system prior a natural weathering for 5.5 years according to EN 927-3 (2020). By frequent evaluations, the impact of chemical modifications ...
L Emmerich, H Militz
Impacts of elevated moisture levels and subsequent drying on screwed
2023 - IRG/WP 23-40970
Mass timber (glue-laminated timber, cross laminated timber (CLT) and laminated veneer lumber) are increasingly used in mid-to high rise structures in Australia where the climate is mainly sub-tropical with elevated moisture levels and high termite risk. Moisture intrusion poses a major challenge anywhere but becomes more critical under these conditions. Untreated/non-durable materials are consider...
C M T Roder, C D Gerber, J J Morrell
Through-boring to improve the performance of low durability Eucalyptus species for utility poles: 10-year field test results of pole stubs exposed in Southeast Queensland
2023 - IRG/WP 23-40972
An impending shortage of naturally durable hardwood electricity pole timbers in Australia has encouraged investigation of alternatives containing less durable, untreatable heartwood. Through-boring or drilling holes perpendicular to the long axis before treatment, has been used successfully on refractory softwood poles in North America and might have application in Australia. The use of through-bo...
J Norton, L P Francis, J J Morrell
New wood-modification process based on grafted urethane groups: Durability of carbamamylated Scots pine (Pinus sylvestris L.) wood
2023 - IRG/WP 23-40974
Substituting commonly used toxic preservatives with wood modification treatments can make the wood material less prone to water and moisture uptake. This approach favours a more sustainable protection of wood against biodegradation. In this study, Scots pine sapwood was full-cell impregnated with an aqueous solution of urea (30%), dried at 40°C for 24h, and subsequently heat-treated at 150°C for...
C-F Lin, O Myronycheva, O Karlsson, D Jones, D Sandberg
Properties of thermal modified wood of Pinus pinaster and Pinus radiata from Galicia, Spain
2023 - IRG/WP 23-40985
This article provides the results of a research about the properties of thermal modified wood of maritime pine (Pinus pinaster Ait.), radiata pine (Pinus radiata D.Don) and Scots pine (Pinus sylvestris L.) from Galicia, Spain, thermal treated in the industrial vacuum-heat autoclave plant of FINSA group in Galicia, Spain. These three pine wood species are used in different solid products but due th...
D Lorenzo, J Benito, J Arancón, J Crespo
Multi-scale Experimental Study on Self-sustained Smouldering of CCA-treated Timber Poles
2023 - IRG/WP 23-40988
While it is accepted that appropriate treatment with chromated copper arsenate (CCA) will extend the design life of wood markedly, there are concerns regarding the effect of treatment on fire performance. Smouldering combustion in CCA-treated timber infrastructure can self-sustain, destroying the timber elements, as the chromium and copper present in the CCA can act as catalysts of the smouldering...
W Wu, L Yerman, J J Morrell, F Wiesner
Modification of wood by fast pyrolysis bio-oil – the NewWave project concept for bio-based wood treatment
2023 - IRG/WP 23-40990
The NewWave project aims to contribute to building a circular economy by introducing sustainable raw materials in different manufacturing lines, replacing toxic chemicals and lowering the environmental footprint of the products. The raw materials are obtained from the thermochemical fractionation of biomass. This process converts biomass residues by fast pyrolysis into Fast Pyrolysis Bio-Oil (FPBO...
A Sandak, J Sandak, F Poohphajai, R Herrera Diaz, A Gubenšek, K Butina Ogorelec, L Kiezebrink, K J Swager, H Heeres, B van de Beld
Optimization of furfurylic alcohol/tannin ratio to improve the performance of biosourced thermoset resins for wood protection
2023 - IRG/WP 23-40994
This study concerns the chemical modification of wood with different ratios of tannin and furfuryl alcohol (FA) in the presence of maleic acid as catalyst. Tannins were used not only as cross-linking agents, but also as co-monomers to improve wood durability, while reducing the amount of FA used. Different aqueous formulations were prepared containing decreasing amount of FA (from 45.45% to 0%) an...
E Azadeh, A Pizzi, P Gérardin, C Gérardin-Charbonnier
Relationships between deterioration part and structural performance in wooden houses
2023 - IRG/WP 23-50376
Based on the survey examples, there are four patterns of deterioration that tend to occur in plywood bearing walls of wooden houses in Japan. The first is a pattern in which wall is in a whole deterioration. It is a no damage wall or test specimen. The second is a pattern in which only the sill is deteriorating. It is caused by moisture or termites from ground to the base. In addition, there is a ...
Y Ota, H Ishiyama, S Okamoto
Improving American Hardwoods Sustainability, Durability and Markets
2023 - IRG/WP 23-50378
The American hardwood industry, which dates back to the first European settlers, has a wealth of experience processing the native hardwoods of North America. The US hardwood resource is mainly located in the eastern United States, from Maine in the North to the Gulf of Mexico in the South and westwards to the Mississippi Valley. The USA has more temperate hardwood species than any other world regi...
D Brooks, M Snow
Enhanced durability of bio-based materials for green building
2023 - IRG/WP 23-50382
Wood protection technologies provide tools to enhance the durability of bio-based materials for green building. Both wood and related bio-based material are regarded as eminent for green building. It allows to underpin several of the United Nations sustainable development goals and is regarded critical for the Green Deal objectives of the EU. Nevertheless, to enhance the potential it needs to be b...
J Van Acker, L De Ligne, J Vand den Bulcke
Australian timber durability research needs
2023 - IRG/WP 23-50385
Australia was once a world leader in timber durability research, but prolonged disinvestment resulted in a gradual decline in capacity. Forest and Wood Products Australia recognized this problem and supported the development of the Centre for Timber Durability and Design Life to help reverse this decline and begin to educate the next generation of Australian researchers. The Centre is a collabor...
J J Morrell
Wood above ground project – Results and future plans
2024 - IRG/WP 24-11041
In 2000, the Danish Technological Institute (DTI) initiated an extensive study to investigate the natural durability of wood. The study involved exposing wood in various orientations to assess its performance. A total of 35 wood material types were exposed at DTI test site in Taastrup, Denmark. Moisture content (MC) was measured through weighing for the initial five years, decay was assessed follo...
A W Christof, R Digaitis, P Fynholm, J Stenbaek, N Morsing, B Lindegaard
Unlocking the potential of paulownia in Malaysia: Durability assessment to mold
2024 - IRG/WP 24-11043
Paulownia is one of the species included in the plantation program in Malaysia due to its fast growth (three to four years) and excellent properties suitable for wide application including furniture, biofuel, musical instruments, and decoration. However, data on its durability to biodegradation is scarce, especially for tropical usage. In this study, a paulownia clone known as Revotropix Paulownia...
S Lipeh, T Khadiran, N A Siam, R Jalil, N F N M Isa
On the use of miniaturized wood specimens in fungal decay experiments – mini-blocks versus EN 113 test specimens
2024 - IRG/WP 24-11044
Preliminary evaluation and classification of wood durability against decay fungi using laboratory monoculture experiments has been a longstanding practice because these tests offer quicker results than field tests. Various methods, including miniaturized specimen formats and different incubation periods, have been explored to expedite decay processes and assess wood preservation efficacy. The 'min...
C Brischke, G Alfredsen
Terpene-based latex synthesis for exterior wood protection
2024 - IRG/WP 24-20715
Driven by challenges in raw material supply chains, the coatings industry is actively seeking biobased alternatives to enhance outdoor wood protection. This study aims to investigate the integration of biobased monomers into latex formulations, aligning with protocols applicable in industrial contexts. A semi-batch emulsion polymerization protocol was developed, designed to be scalable and meet es...
M Carrère, V Landry
Studies on the treatability of selected pine species and corresponding efficacies of a new non-biocidal treatment
2024 - IRG/WP 24-20721
Wood decay caused by fungi may reduce the service life of wood in outdoor applications. Since moisture conditions in wood occur as one of the most crucial parameters for fungal decay, chemical modifications, which affect the latter, may increase the resistance of wood against such organisms. Usually, pine sapwood is easier to chemically treat than heartwood, as the former generally shows good perm...
T R da Silva Lins, L Emmerich, H Militz, P H Gonzales de Cademartoni, R J Klizke, M Pereira da Rocha
The potential of Wacapou (Vouacapoua americana) extracts to develop new biobased protective solutions for white woods
2024 - IRG/WP 24-20724
The valorisation of Amazonian wood residues into active chemical compounds could be an eco-friendly, cost effective and valuable way to develop wood preservatives formulations in order to enhance the decay and termite resistances of low durable wood species, by impregnation processes. Wacapou (Vouacapoua spp., Fabaceae) is a well-known Guianese wood species for its use in local wood construction ...
E Kieny, K Candelier, L Milhe, Y Estevez, C Sophie, R Lehnebach, J Damay, D Florez, E Hoël, M-F Thevenon, J Bossu
Elevated pressure hybrid wood modification: Synergistic effects on durability performance
2024 - IRG/WP 24-20725
The combination of different wood modification technologies to obtain improved performance is increasingly receiving attention in research. In this study, Scots Pine was impregnated with furfuryl alcohol (FFA) in pure aqueous 20, 40 and 60% solution strength without adding any catalyst. In a second step, the FFA was polymerized while simultaneously performing thermal modification in a closed syste...
P Klaas, D Jones
Preservative properties of boron-treated paulownia wood
2024 - IRG/WP 24-20729
This research was performed to investigate the preservative retention properties of paulownia wood treated using boric acid/borax at mass ratio of 1:1.8. Different portion of paulownia wood (top, middle, bottom) were used as a sample throughout of this study. In the treatment process, the paulownia wood was dipped in the 1% boric acid/borax solution for 1, 24, 72, 120 and 240 hours to achieve requ...
T Khadiran, M A M Abdullah, S Lipeh
Properties of thermal modified wood of Pinus pinaster, Pinus radiata and Pinus sylvestris from Galicia, Spain
2024 - IRG/WP 24-30800
This paper provides the results of a research about the properties of thermal modified wood of maritime pine (Pinus pinaster Ait.), radiata pine (Pinus radiata D. Don) and Scots pine (Pinus sylvestris L.) from Galicia, Spain, thermal treated in the industrial vacuum-heat autoclave plant of FINSA group in Galicia, Spain. These three pine wood species are used in different solid products but due the...
D Lorenzo, J Benito, J Arancon, J Crespo
Physical, durability and chemical characterization of Gmelina arborea (Roxb.) wood treated with lactic acid
2024 - IRG/WP 24-30803
The increase in demand for durable wood has drawn attention to the use of fast-grown plantation species across the globe. Chemical modification was used to treat Gmelina arborea wood with lactic acid for property enhancement. The treated samples were obtained from two different ages of 15 and 10 years and sawn into (20 x 20 x 60) mm and (20 x 20 x 20) mm for physical, durability and chemical chara...
T O Akinwamide, J M Owoyemib, E A Iyiolac
Preliminary investigation of the durability and performance of 1,3-dimethylol-4,5-dihydroxyethylene urea (DMDHEU) treated aspen strandboard
2024 - IRG/WP 24-30804
Wood modification technologies are growing in popularity because of their potential to improve wood properties by permanent covalent chemical modifications rather than chemical impregnation. These features can be utilized in wood composites to help improve dimensional stability and composite resistance to fungal decay. In this study, 1,3-dimethylol-4,5-dihydroxyethylene urea (DMDHEU) was used to m...
S Johnson, F Kamke, G Presley