Your search resulted in 165 documents. Displaying 25 entries per page.
Further discussion of biological durability assessments of acetylated wood from several European institutes
2006 - IRG/WP 06-40340
In the last decade, interest in the development of wood modification systems has increased in Europe. Alongside several industrial initiatives for heat treatments, there have also been scaling up and pilot plant projects for chemical wood modification. Between 2000-03, the European Commission funded the "Thematic Network on Wood Modification". This paper features a re-evaluation of work undertaken...
D Jones, W Homan, F Bongers
Criteria for environmentally and socially sound and sustainable wood preservation industry
2006 - IRG/WP 06-50237
This paper is dealing with critical criteria for environmentally and socially sound and sustainable wood preservation industry. A research study supported by past experience, knowledge and training on relevant topics and consultation of relevant appraisal manual, training module and technical guideline revealed concise widespread checklists for sustainable establishment of wood preservation indust...
A K Lahiry, M Hasan, M A J H Chowdhury
Wood furfurylation process development. Part 1: Oscillating Pressure Method
2007 - IRG/WP 07-40376
Furfurylated wood (wood modified by furfuryl alcohol) has over the last years gained marked shares from both tropical wood and conventional preservative treated wood and this has, in turn, generated several research projects concerning process development. The impregnation of spruce is well known from literature to be a difficult task. Furthermore, the sapwood of Scandinavian-grown Scots pine is a...
E Larnøy, M Westin, B Källander, S Lande
Wood furfurylation process development. Part 2: Lowry impregnation trials
2007 - IRG/WP 07-40377
The objective was to evaluate whether Lowry-impregnation of Scots pine with FA100-mix, instead of the FA40-mix, would lead to similar or slightly higher WPGs and to investigate any potential changes in penetration pattern. The results indicate that the penetration was better, also penetrating the outer zone of the heartwood. Furthermore, it was possible to reduce the WPG-levels for pine down to 50...
M Westin, E Larnøy, S Lande
Preservative treatment of Golla cane (Daemonorops jenkinsiana) by pressure process
2007 - IRG/WP 07-40379
The feasibility of preservative treatment of golla cane (Daemonorops jenkinsiana (Griff) Mart). by pressure process has been studied using water borne preservatives CCB (copper-chrome-boron). Cane samples of three different lengths 1m, 2m and 3 m. were treated at different pressure and time period to evaluate the extent of penetration and retention of preservative chemicals. It was observed that t...
K Akhter, M Hoque Chowdhury
Reduction of Environmental Toxicity Through Eco-friendly Wood Biopreservative
2007 - IRG/WP 07-50243
Many chemicals are used today to enhance the durability of wood and wood-derived products that are very important in our life. Such chemicals are copper, chromium, arsenate, zinc, etc. Though these preservatives are useful to protect wood from biodeterioration, but environmental toxicity is also related with them. The present study is to investigate the fungitoxic activities of Dalbergia sissoo le...
A Humayan Kabir, M Firoz Alam
Theory of Aesthetics – Charm in Furniture and an Aesthetic Evaluation of Bleaching of the Natural Color of Wood through the Application of Experimental Bleaching Process
2007 - IRG/WP 07-30424
This paper consists of mainly three sections: In the first section, brief information is given on the theory of aesthetics as a branch of philosophy, historical progress of the aesthetics theory is summarized within the context of the term “beautiful”, and aesthetic values as well as the color and aesthetic effects of color in preparing the designs are explained. In the second section, relatio...
I Usta
The influence of different creosote process parameters on penetration, retention and bleeding on glulam
2007 - IRG/WP 07-40368
Different process parameters were used to treat Scots Pine glulam beams with creosote. Parameters like pre-heating, pre-pressure time, pressure and pressure time were changed. Most treatments gave a full or almost full penetration of creosote into the sapwood, but the uptake of creosote in the sapwood varies.
All samples, except the one with poor penetration, showed heavily bleeding of creosote ...
F G Evans
Evaluating the Process of ACQ-Treated Woods with TGAand CEM Analysis
2007 - IRG/WP 07-20374
To provide an understanding of the fundamental thermal behaviour and the disposal-end products of ACQ-treated woods, this study is comprised of two categories of examination. The first is related to the use of TGA under different thermal decomposition conditions (nitrogen or air, and 5 or 40 oC/min), and the use of EDX to examine certain residual elements of the char. The second applies the CEM ...
Han Chien Lin, Tsang-Chyi Shiah, Jung Ting Tsai
Efficacy of Neem (Azadirachta indica) Leaves Against Wood Decay Fungi
2008 - IRG/WP 08-30450
Many plant-derived substances have fungitoxic, pecticidal and insecticidal ability. Neem leaves are very popular in this respect since the ancient time. The present study is to investigate the fungitoxic activities of neem leaves extractives against wood decay fungi. Three different solvents, i.e. acetone, methyl alcohol, ethyl alcohol, were used to isolate the extract of neem leaves. The extracti...
A Humayan Kabir, M A Rahman, M Firoz Alam
Influence of boiling on the quality of oakwood during peeling processes
2008 - IRG/WP 08-10656
Peeling process may be an efficient technology to transform secondary quality trees into veneer. After cutting and drying, veneer can be used for plywood or LVL production. If natural durability of these new panels is sufficient, they may be used for joinery production without preservative treatment. With the collaboration of ENSAM Cluny, Zvolen University and Pau University, we have investigated ...
M Svoradová, F Charrier, R Marchal, L Bléron, B Charrier, J-C Butaud
Preservative treatment of strips of Bambusa balcooa by soaking process using Borax-Boric acid
2008 - IRG/WP 08-30478
Bamboo strips made from Borak bamboo (Bambusa balcooa) were treated with 10% borax-boric acid aqueous solution by soaking process. The moisture contents of the bamboo strips were 12%, 20% and 30%. The strips were soaked for one, two, three, four and five days. The penetration of the
solution was investigated by colour test after soaking and drying. Full penetration was observed after three days ...
K Akhter, M W Sheikh, M M Rahman, T A Chowdhury, M H Chowdhury
Effects of bleaching process on the roughness values of wood surfaces of Lebanon cedar (Cedrus libani A. Rich.) and Black poplar (Populus nigra L.) using NaOH (sodium hydroxide), H2O2 (hydrogen peroxide) and Ca(OH)2 (calcium hydroxide)
2008 - IRG/WP 08-40403
Technical progress in the wood industry has been rapid in recent times. In this case, the quality assurance of the consumer products aligned with aesthetics value appears as one of the most important parameters. Because of the outer appearance of goods exert an effect on customers, interest in production of high quality surfaces of wooden commodities has increased essentially based on the surface ...
I Usta, E Aydinlar
Effects of Murgul Copper Process flue gases (SO2) on compression strength parallel to the grain of Beech (Fagus orientalis Lipsky.) wood
2008 - IRG/WP 08-40404
In this study was investigated the effect on the compression strength parallel to the grain as mechanical properties of Fagus orientalis Lipsky. wood exposed to SO2 gas and non-exposed.
In the experiments the two of four (total) were obtained from Artvin-Ortaköy region and the other two from Artvin-Murgul region. The compression strength parallel to the grain was calculated at the compare of ...
N Ay, E Topaloglu, A Uncu
Improvement of the Fungal Resistance of Japanese Cedar by the ThermoWood Process
2008 - IRG/WP 08-40422
The effect of the ThermoWood Process on sapwood of the Japanese cedar, Cryptomeria japonica, was investigated. Seven matched specimens were cut from a sapwood board of Japanese cedar and subjected to thermal treatments according to the ThermoWood Process.
The decay resistance and chemical and physical properties of the treated specimens and untreated specimen were investigated. The decay test wa...
I Momohara, T Morita, S Shouho, A Yamaguchi
Impregnación de durmientes de quebracho blanco (Aspidosperma quebracho blanco) con preservadores cromocuproarsenicales (CCA)
2008 - IRG/WP 08-40428
CCA impregnation of railroad ties is a recent process in Argentina which has not been optimized in a commercial scale. This study analyzed the influence of treatment pressure on final retentions to optimize the impregnation process. Results showed that a 3.2% m/v solution resulted in 10.8 kg/m3 CCA retention. At 1187 kPa (12 kgf/cm2) quebracho blanco wood had an average absorption of 338 l/m3. Als...
D Gherscovic, Z Cataldi, J M Languasco
Rehabilitación del Portón del templo parroquial de San Juan Vicario de Comanja, Michoacán, México
2008 - IRG/WP 08-40431
The pine gate of the San Juan Vicario parochial temple in the city of Comanja, Michoacan, Mexico was rehabilitated. The gate was damaged by termites, worms, fungi and weathering. Gate metallic bearings were rusted. The lower parts of the gate were the most deteriorated. For rehabilitation, galvanized steel bearings were designed and manufactured and then implemented into the building. Replacement ...
J Reséndiz Sánchez, J Cruz de León
Antifungal Activities of Three Supercritical Fluid Extracted Cedar Oils
2009 - IRG/WP 09-30501
The antifungal activities of three supercritical CO2 (SCC) extracted cedar oils, Port-Orford-cedar (POC) (Chamaecyparis lawsoniana), Alaska yellow cedar (AYC) (Chamaecyparis nootkatensis), and Eastern red cedar (ERC) (Juniperus virginiana L), were evaluated against two common wood decay fungi, brown-rot fungi (Gloeophyllum trabeum) and white-rot fungi (Trametes versicolor). The statistical analysi...
Tianchuan Du, T F Shupe, Chung Y Hse
Effects of concentration and temperature of CCA and CCB on wood strength of Turkish fir (Abies bornmulleriana Mattf.)
2009 - IRG/WP 09-40450
The purpose of this study was to present evidence for the effects of concentration and temperature of solutions of water-borne preservatives (chromated copper arsenate, CCA and chromated copper boron, CCB) on the static bending properties (modulus of elasticity, MOE and modulus of rupture, MOR) of Turkish fir (Abies bornmulleriana Mattf.). Wood samples were mechanically tested after a mild full ce...
I Usta, M Hale
Eco-Friendly Composites from Bagasse and Soy-based Resin
2009 - IRG/WP 09-40462
In this study, bagasse and soy-based resin were used for producing composite materials. The objective of this study was evaluation of some physical and mechanical properties of boards made of various ratios (100:0, 60:40, 40:60 and 0:100) of bagasse to wood fiber mixtures (wt: wt) with addition of Soy/PF resin at three levels (4, 8 and 10%) and 1.5% wax. All properties were tested according to AST...
G Rassam, B Jamnani
Study of Microscopy Properties of Modified Wood During Weathering Process
2010 - IRG/WP 10-40517
In this study spruce (Picea excelsa) and Beech (Fagus orientalis) wood acetylated and has been subjected of artificial weathering in difference times (0, 50,150&300 h), then wood surface analyzed using Scanning Electron Microscopy (SEM). The SEM results shown that the surface of wood exposed to weathering undergoes distinct physical changes and the surface degradation appears to be directly propor...
M Akhtari
Preservative Treatment of simul (Bombax ceiba) Veneers with Hot and Cold Water Solution of borax-boric acid by Soaking Process
2010 - IRG/WP 10-40528
Veneers of simul (Bombax ceiba) were treated with different concentrations of water- borne preservatives borax-boric acid (BB) by soaking process for different time periods. In the case of hot water treatment, it was found that the average retention of preservative chemicals increased gradually with the increasing treatment period from 20 minutes to 60 minutes. Similar trend was observed in the ca...
K Akhter, Md Abul Hashem, S Akhter
Lignin blocking effects on weathering process of wood plastic composites
2010 - IRG/WP 10-40529
The weathering of wood–plastic composites (WPC) causes discoloration which affects their aesthetic aspects. It has been proved that these discolorations are due to lignin degradation. Effects of blocking the susceptible structure of lignin assessed by chemical treatment such as acetylation and methylation are reported in this study. Surface chemical change of wood plastic composite (WPC) formula...
P Darabi, A Naghi karimi, S Ahmade Mirshokraie, M-F Thévenon
Bioresistance of Poplar Wood Compressed by Combined-Hydro-Thermo-Mechanical Wood Modification (CHTM) Process
2010 - IRG/WP 10-40532
Bioresistance of treated Poplar wood by CHTM process (Combined-Hydro-Thermo-Mechanical Wood Modification) was studied in the current research work. Resistance against brown rot fungus Gloeophyllum trabeum as well as the soft rot decay was the main concern of this work. Poplar wood blocks were hydrothermally treated at temperatures of 120,150 and 180°C for holding time of 0, 30 and 90 min. afterwa...
L Khademi-Bami, B Mohebby
Towards designing eco-friendly buildings with in-built termite protection
2010 - IRG/WP 10-50273
The increase in greenhouse gases, leading to global warming, is considered by a consistent scientific worldview not due to natural variation, but due to the growing concentration of carbon dioxide (CO2), methane (CH4) and other atmospheric pollutants. Global emissions of carbon dioxide from fossil fuel combustion and cement production rose from 22.6 billion tons in 1990 to an estimated 31.2 billio...
J R J French, B M Ahmed Shiday, B Maggiolo, D Maggiolo