Your search resulted in 486 documents. Displaying 25 entries per page.
Accelerated weathering and fungal resistance of wood modified with isopropenyl acetate
2016 - IRG/WP 16-40764
Chemical modification of Rubberwood (Heveabrasiliensis Müll.Arg) with isopropenyl acetate (IPA) in presence of anhydrous aluminum chloride and iodine as catalysts was carried out. Modified wood surfaces were exposed to UV light source in an accelerated weathering tester to evaluate UV resistance. Anti-swelling efficiency (ASE) and fungal resistance of modified wood were also evaluated. Modified w...
G B Nagarajappa, K K Pandey
Fire retardant treated wood products – Properties and uses
2016 - IRG/WP 16-30701
Wood is combustible, but can still perform very well in fire, especially for load bearing structures. However, visible wood surface may not fulfil the fire requirements in building codes and fire retardant treatments may be an option. The highest reaction to fire classification for combustible products may then be reached. However, the excellent fire performance of the virgin fire retardant treate...
B Östman, L Tsantaridis
Effects of climatic factors and material properties on mould growth on untreated wooden claddings
2017 - IRG/WP 17-10884
Mould growth is an important contributor to colour change of untreated wood exposed outdoors. Predicting the development of mould growth is therefore important to ensure successful use of untreated wood as a façade material. More knowledge about the factors affecting mould growth on outdoor exposed wood is required to give better predictions. In this study, climatic factors and material propertie...
S Karlsen Lie, G I Vestøl, O Høibø, L Ross Gobakken
Chemical compositions and anti-termite activities of essential oils from Gabonese Canarium schweinfurthii Engl, Dacryodes buettneri Engl and Aucoumea klaineana Pierre wood resins.
2017 - IRG/WP 17-10895
Essential oil extract from resins of Canarium schweinfurthii, Dacryodes buettneri and Aucoumea klaineana woods from Cap Esterias and Oyem areas, Gabon, were prepared by Clevenger - steam distillation. The chemical compositions of these respective essential oils were analyzed by a Gas Chromatography coupled with Mass Spectrometry (GC-MS). Although monoterpenes were the main constituents of the thre...
Chemical compositions and anti-termite activities of essential oils from Gabonese Canarium schweinfurthii Engl, Dacryodes buettneri Engl and Aucoumea klaineana Pierre wood resins.
Overview of the treated wood quality control program in the United States with the recent challenges and advances
2017 - IRG/WP 17-20616
In the past two decades, there have been significant and rapid changes in wood protection technologies for residential applications which have moved away from long established heavy duty metal oxide based products such as chromated copper arsenate (CCA). The successor generation of wood protection systems usually contain copper as the primary biocide, in combination with carbon-based co-biocides s...
L Jin
Effects of Nano-Wollastonite Impregnation on Fire Properties of Some Thermally-Treated Solid Wood Species
2017 - IRG/WP 17-40771
The effects of nano-wollastonite (NW) suspension impregnation on the fire-retarding properties of heat-treated solid wood of three species (beech, poplar, fir) were studied. Heat treatment was performed at two temperatures of 180 °C and 200 °C. Impregnation was carried out at a pressure of 3 bars for 30 min. The fire properties included ignition time, glowing time, back-darkening, back-splitting...
H R Taghiyari, R Hossinpourpia, S Adamopoulos, A Jahangiri, D Rabie
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Dimensional Stability of Melamine Formaldehyde-Treated Southern Pine
2017 - IRG/WP 17-40774
The objective of this preliminary study was to evaluate the influence of different levels of melamine formaldehyde (MF) and curing cycle on the dimensional properties of southern pine. Thirty samples for each combination of treatment and curing regimen plus untreated controls and controls subjected to the same curing regimen were tested. Shrinkage/swelling coefficients showed that up to 60% ASE c...
H M Barnes, L S Sites, T S F A França, M G Sanders, F J N França
Susceptibility to filamentous fungi of plywood for furniture coated with waterborne acrylic lacquers
2017 - IRG/WP 17-40778
Filamentous fungi (mould), thanks to their little trophic requirements belong to organisms which grow exceptionally easy and fast in favorable hygrothermal conditions and attack both organic and inorganic materials even with only trace amounts of organic substances on the surface. The fungi often cause spoilage of foodstuffs, worsen the aesthetic of wood-based elements, and pose a threat to the en...
A Fojutowski, M Nowaczyk-Organista, P Hochmańska
Accessibility of hydroxyl groups in anhydride modified wood as measured by deuterium exchange
2017 - IRG/WP 17-40784
Acetylated wood shows improved properties largely due to the reduced amount of water in the acetylated cell wall. However, the exact mechanism by which water is excluded in acetylated wood remains unclear. Acetylation reduces hydroxyl content by substitution of hydroxyl groups in wood polymers but may also hinder access to unmodified hydroxyls by physical bulking. This work assesses hydroxyl acces...
G Beck, S Strohbusch, E Larnøy, H Militz, C Hill
Physico-Mechanical and Biological Properties of Cement Bonded Particleboards from Nordmann Fir
2017 - IRG/WP 17-40798
Wood species, wood-cement ratio and curing accelerator types are the major factors effecting properties of wood-cement composites. This paper investigates the effects of wood-cement ratios and cement curing accelerator types on some properties of cement bonded particleboards (CBPBs) from Nordmann fir [Abies nordmanniana (Stev.) Spach. subsp. Nordmanniana]. A total eight groups of the experimental ...
H Yel, U Aras, H Kalaycioglu
The Effects of Pre-Microwave Treatment on Retention Levels And Some Mechanical Properties of Spruce Wood Treated with CCA
2017 - IRG/WP 17-40800
Microwave (MW) treatment of wood has been evaluated in recent years for different purposes by several scientists. Microwave conditioning improves permeability, reduces density and heat conductivity and changes dimensional stability. Furthermore, it could even improve the permeability of refractory wood species such as spruce and Douglas fir. In this study, MW pre-treatment was applied to spruce wo...
E D Gezer, S Kuştaş, S Durmaz
Impact of heat treatment on physico-mechanical properties of torrefied Antholceistha djalonensis wood
2017 - IRG/WP 17-40811
Thermal modification at relatively high temperatures is an effective method to improve the dimensional stability and mechanical properties of wood. This study was carried out to investigate the impact of heat treatment on the physic-mechanical properties of torrefied Anthocleistha djalonensis wood. Thirty nine defect-free specimens of dimensions 20 mm × 20 mm × 60 were prepared for the determina...
E A Iyiola, B Olufemi, J A Fuwape, J M Owoyemi
Influence of hygro-thermal treatment temperature and duration on dimensional stabilisation of wood modified with poly(butylene succinate)
2017 - IRG/WP 17-40813
To improve wood properties, especially dimensional stability, a treatment based on poly(butylene succinate) oligomers (OBS) was experimented. After impregnation in wood, a further hygro-thermal treatment (HTT) was carried out in a pressurized reactor at 100% relative humidity (RH) at differing temperatures for differing durations. The aim of HTT is to induce partial swelling of wood cell walls so ...
C Grosse, M Noël, L Rautkari, P Gérardin
A Green and Novel Technology for Recovering Copper and Wood from Treated Wood Waste – Part II: Optimization, copper metal recovery, and process design
2017 - IRG/WP 17-50326
The US consumes 70 million pounds of copper and produces 580 million cubic feet treated wood annually. The EPA disallows burning and reusing treated wood waste due to health/environmental concerns. Vast quantities of copper and wood are landfilled. Two safe and low cost extraction systems, citric acid and ammonium citrate, were identified in Part I of this study. In Part II of the study, effects o...
S Chen, R Patel
Corrosion verification experiment of the screw driven into CLT
2017 - IRG/WP 17-40816
Japan has abundant forest resources, but we depend on import for 70 percent of the consumed timber. Japan has the vision which promotes the timber self-sufficiency rate 30% to 50% by 2020. Therefore CLT attracts attention as a new timber material. Japan has a climate with high temperature and humidity, and wooden buildings are often treated with chemicals as a measure against biological deteriorat...
N Wada, H Ishiyama, S Yamamoto
Effects of exposure time on detection of the behavior of white-rot fungi on Oriental beech wood properties
2017 - IRG/WP 17-10902
The comparison of fungal degradation of Orientalis beechwood by two white-rot fungi was evaluated in this study. Biological, mechanical, and chemical assessments of beech wood were carried out at 30 day interval for 120 days. The results demonstrated that both fungi have greater effects on beech wood during each exposure time. However, Trametes versicolor degraded beech wood more effectively than ...
E Bari, D D Nicholas, K M Ohno
Mechanical, Physical and Biological Properties of Sandwich Biocomposites Panels manufactured from Food Packaging Waste
2017 - IRG/WP 17-40791
Recently, recycling of Tetra Pak® packaging material has attracted many attention, particularly in composite industries. In this work, novel biocomposites sandwich structures were manufactured using TetraPak waste materials as core component and various kind of natural and artificial woven fabrics as skin elements. Mechanical, physical and biological performances of the developed composite panels...
A S O Mohareb, A H Hassanin, K Candelier, M F Thévenon, A Kilic, Z Candan
Biocontrol of wood decay insects and nematodes as an alternative to traditional chemical treatments
2018 - IRG/WP 18-10914
The protection of wood has been defined until relatively recently, as the application of a chemical to increase its durability. On the other hand, society is becoming more and more demanding in terms of the use of products which have the minimum ecological impact. This has led many countries to reduce the list of biocidal products that can be used (European Biocides Regulation), therefore it is ne...
L Robertson, J F Galván, F Llinares, R Viñambres, M T de Troya
Natural resistance of Bambusa vulgaris to termite and powder-post beetle attack in laboratory and graveyard tests
2018 - IRG/WP 18-10925
Deterioration is the major setback to the utilisation of bamboo products. To enhance bamboo utilization, an understanding of the level of resistance to degradation is important. In this study, level at which Bambusa vulgaris will naturally resistant attack by subterranean termites and powder-post beetles were evaluated. B. vulgaris aged 2, 3 and 4 years were subjected to attack by subterranean ter...
N A Sadiku, S O Bada
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Chemical composition and termiticidal activity of Khaya ivorensis stem bark extracts on woods
2018 - IRG/WP 18-30723
The genus Khaya is extractives rich, but the extractives in the stem bark are among the most abundant, accessible and utilised materials in Nigeria. These extractives are of considerable interest for wood protection because of their pesticidal properties. In this study, the chemical constituents of Khaya ivorensis stem bark (KISB) and their termiticidal activity were investigated on Triplochiton s...
G A Adedeji, O Y Ogunsanwo, F S Eguankun, T O Elufioye
Bio-preservative properties of technical lignins from South African pulp mills: An investigation towards a conceptualized development of natural compound-based wood preservatives
2018 - IRG/WP 18-30724
The depletion of naturally durable timber and the risk posed by some of the conventional wood preservatives to human health and the environment continue to drive research efforts towards developing new formulations that are benign. Furthermore, the global concept of environmental sustainability aims at optimal use of resources and to comprehensively include conversion of waste to value added produ...
A Alade, L Tyhoda, M Meincken
FTIR-ATR monitoring of chemical changes of thermo-chemically modified beech wood degraded by brown-rot fungus
2018 - IRG/WP 18-40823
Wood chemical modification with lactic acid oligomers (OLA) has been reported to confer promising properties for wood outdoors applications. To better understand the lactic acid interaction with wood, chemical changes following biological degradation have been characterized with a battery of tests. Fourier transform infrared (FTIR) spectroscopy has been proved to be a valuable tool for studying fu...
C Grosse, M Noël, M-F Thevenon, P Gérardin
Resistance of modified wood to termite attack assessed in laboratory and field testing: A review of internal research
2018 - IRG/WP 18-40824
Within the past decades, new wood modification technologies have been investigated in order to improve certain wood characteristics and enable the use of timber products for outdoor applications. Some of these non-biocidal technologies have been developed and commercialized recently. Thus, various material properties were studied intensively and shown to be improved. To a great extent, previous re...
L Emmerich, P Gascón-Garrido, H Militz