Your search resulted in 560 documents. Displaying 25 entries per page.
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Degradation of Eucalyptus transmission poles varies across regions in Zambia
2018 - IRG/WP 18-30727
Evidence from literature shows that Eucalyptus poles treated with creosote last over 30 years before replacement. However, in Zambia, the life span of such poles has reduced to 5-10 years. The aim of this study was to investigate factors associated with degradation of treated Eucalyptus poles and how these varied across regions in the country. A total of 1200 poles were assessed in three differen...
P Ng’andwe, D Chungu, E Ncube
Performance of acetylated wood in aquatic applications
2018 - IRG/WP 18-40822
Acetylation of wood to enhance its resistance against wood decaying fungi and insects has been studied extensively under both laboratory and terrestrial field trials. Also several studies are investigating the performance of acetylated wood in marine and fresh water exposures. This paper updates nine year marine tests with acetylated radiata pine in Hejlsminde (Denmark) and presents data on 3 year...
F Bongers, S Palanti, A Gellerich, J J Morrell, J Creemers, J Hague
Long-term performance of DMDHEU-treated wood exposed in ground, above ground and in the marine environment
2018 - IRG/WP 18-40825
Chemical wood modification with N-methylol compounds such as 1.3-dimethylol-4.5-dihydroxyethyleneurea (DMDHEU) has been studied intensively since the 1990s. Research of the past years focused on treatment of Scots pine (Pinus sylvestris L.) and European beech wood (Fagus sylvatica L.) and was shown to be applicable to improve specific material properties. A high resistance against wood-destroying ...
L Emmerich, H Militz, C Brischke
Enhancing service life performance of oak decking and cladding using organosilicon treatments
2018 - IRG/WP 18-40838
The Life+ project SILEX, in full “Improving sustainability of construction materials using innovative Silicon based treatment” started in April 2013 and was finalized mid 2017. The aim of this project was to demonstrate that a new class of compounds can be used for wood treatment for an extended service life combined with enhanced new testing methodology. Ultimately, it was the intention to de...
J Van Acker, J Van den Bulcke, J-P Lecomte
Performance of wood exterior structures above ground in Spain built with softwood species. The situation case of a shelter bridge
2018 - IRG/WP 18-40844
Across Europe is very common to find wood exterior structures build in sawn and glue-laminated wood. Most of these exterior wood structures use softwood wood species such as: fir, spruce, larch and pine. In Spain exterior wood structures, became more and more popular since nineties, when sawn and glue-laminated wood were utilized for building exterior wood structures in overall Spain. This paper s...
D Lorenzo, M Touza, J Fernández-Golfín, A Lozano, J Benito
Developments within COST Action FP1303 related to the modification of wood
2018 - IRG/WP 18-40847
COST Action FP 1303 (Performance of bio-based building materials) was established in 2013 with the main aim to improve the knowledge on the performance of bio-based materials used as building products and the assessment of factors influencing these, with the aim of increasing their service life. This Action has helped in understanding the interlinked relationships between durability, product aesth...
D Jones
Long service life or cascading? The environmental impact of maintenance of wood-based materials for building envelope and their recycling options
2018 - IRG/WP 18-50336
A major restraint in choosing bio-based materials (i.e. wood-based) for external use, is the lack of confidence that architects, designers and customers have toward these materials. In particular, the limit state of bio-based materials, which defines the frequency of maintenance operations, might be reached earlier for wood than for other materials (i.e. concrete). On the other hand, resource and ...
M Petrillo, J Sandak, P Grossi, A Kutnar, A
Enhancing knowledge transfer in the wood protection sector
2018 - IRG/WP 18-50338
In order to meet the needs for the developing bio-based economy, maintaining and expanding the market potential for wood raw materials and wood products in indoor and outdoor construction uses remains a key activity for industries in the biotechnological and forestry sector respectively. A major restraint in this respect is the drastically deviating views and expectations on quality and performanc...
C Brischke, G Alfredsen, S Bollmus, M Humar, D Jones, L Meyer-Veltrup, L Nunes
Declaring life cycle inventory of toxicity related emissions in environmental product declarations of preservative treated wood products
2018 - IRG/WP 18-50339
Life cycle assessment (LCA) including impacts on toxicity for preservative treated wood has been shown to have large uncertainties. With the growing demand for verified LCA in environmental product declarations (EPD), the need for reliable data is crucial for realistic assessment of wood products. Uncertainty is caused by several issues such as service life prediction, leaching rates and calculati...
L G F Tellnes, C Askham, P-O Flæte, M Klamer
Performance of untreated timbers in above ground decking tests: Preliminary results from an international collaborative trial
2019 - IRG/WP 19-10940
The ability to accurately predict wood decay risks under varying environmental conditions has long been of interest to timber users. Accurate predictions are difficult owing to the myriad of variables associated with the decay process including wood species, wood inhabiting organisms, timber building element design and environmental conditions. Despite these difficulties, decay predictions have be...
L P Francis, J Norton, E Melcher, A H H Wong, J Kok Lai, M Klamer, M J Konkler, J J. Morrell
Using X-ray micro-CT to evaluate density loss in anobiid infested wood
2019 - IRG/WP 19-10956
Considering the relevance of wood borers in construction, the present study had as main objective the evaluation of the impact of anobiid damage on timber elements by establishing an empirical correlation between lost material percentage (LM%, consumed by beetles) and apparent density (original – OTD and residual – RTD). Since the beetles’ attack produces a diffuse damage with a set of tunne...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Comparative performance of wood/wood-based claddings predicted by four hygrothermal simulation tools
2019 - IRG/WP 19-20646
A number of hygrothermal numerical simulation packages are available, either wholly or partially dedicated to heat, air and moisture transfer simulations of building materials and wall assemblies. The objective of this work was to compare the hygrothermal responses and the moisture performance of western red cedar and composite wood claddings of a wood frame wall as predicted by four hygrothermal ...
M Defo, M Lacasse, A Laouadi
Performance of wood decking after 5 years of exposure: verification of the combined effect of wetting ability and durability
2019 - IRG/WP 19-20647
Wood is one of the most important construction materials and its use in building applications has further expanded in recent decades. In order to enable even more extensive and reliable use of wood, factors affecting wood’s service life need to be understood. More recently, a new concept to characterize the durability of wood-based materials and to predict the service lives of wood was proposed,...
M Humar, D Krzisnik, B Lesar, C Brischke
Durability by design – a case study of the performance of wooden decks after 9.5 years of natural weathering
2019 - IRG/WP 19-20648
The service life expected for wood decking manufactured with poorly durable wood species, left untreated and exposed to severe environmental conditions such as high humidity and active biological agents, is usually assumed to be short (less than 10 years). The current classification of wood’s natural durability is based on EN standardised tests which do not fully reflect the real end-use conditi...
M Kutnik, M Montibus
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Visual assessment of longitudinal wheel timbers and assessing the feasibility of extending wheel timber service life in the UK railway network
2019 - IRG/WP 19-20651
Timber has been a versatile building material for centuries and during the start of the Railway Age in the nineteenth century it was in considerable demand for use in the railway network, particularly bridge building. Timber is still in service and widely used throughout the UK railway network. The resilience and favourable strength to weight ratio and its relative ease of fabrication make it an...
J R Williams
The Structural Performance of the Nail Driven into the Decayed Wood
2019 - IRG/WP 19-20652
In late years there are many actions to long-term excellent house realization. We have to consider repair or reinforcement for long-term and safety use of wooden house. There are various studies focused on structural performance of decayed wood. It is important for long-term use of wooden house that structural performance of nailed joint on decayed wood is accurately evaluated. However, there are ...
N Wada, H Isiyama
Performance of modified wood in service - multi-sensor data fusion and its multi-way analysis
2019 - IRG/WP 19-20660
Recent developments in the field of electronic sensors and analytics provide new opportunity for accurate characterization of materials often based on portable and non-destructive methods. By using several complementary techniques, the material description is precise and complete. The data provided by multiple equipment, however, are often not directly comparable due to different resolution, sensi...
A Sandak, J Sandak, M Cocchi
Performance based specification of wood – Introducing project CLICKdesign
2019 - IRG/WP 19-20661
This paper introduces the new ForestValue research project CLICKdesign – delivering fingertip knowledge to enable service life performance specification of wood. This European consortium is working on the primary innovation to move from the complex, fragmented and general to the easy-to-use, consolidated and specific by provision of an accessible digital tool for specifiers. Competing materials ...
E Suttie, C Brischke, E Frühwald Hansson, S Fortino, J Sandak, M Kutnik, G Alfredsen, C Lucas, R Stirling
Service life planning of wooden structures: Mathematical prediction models versus professional experience
2019 - IRG/WP 19-20663
During the last 15 years, enormous efforts have been made in developing models for predicting the service life of wooden structures and components. Currently, a framework of how exposure, dimension, design details and the material-intrinsic and the ability to take up and release water can be linked to model the moisture risk in wood products is in principle available.
The aim of this study was to...
C Brischke, J Niklewski, M Humar, G Alfredsen
Protecting Sustainable Wood Infrastructure ̶ Improving the Performance of Poles, Piles, Ties & Timbers with Dual Treatments
2019 - IRG/WP 19-30735
Wood is by far the best structural material in terms of environmental impact, as shown by a number of LCA studies. This environmental impact superiority can be improved if the longevity of the commodity is extended. The main durability concern in large cross-section treated materials is the susceptibility of the heartwood to decay, as it is not typically treatable using traditional methods. This ...
J Lloyd, A Taylor, C Brischke, N Irby, M Manning
Identification of Antifungal Compounds in Konjac Flying Powder and Assessment against Wood Decay Fungi
2019 - IRG/WP 19-30737
The antifungal activity of konjac (Amorphophallus rivieri) flying powder (a by-product produced during mechanical processing of konjac flour) ethanol extract was evaluated against wood decay fungi in culture. Compounds associated with antifungal activity in the extracts were isolated and purified by silica gel column chromatography. The antifungal active fractions were identified by ultra-high-per...
Z Bi, F Yang, Y Lei, J J Morrell, L Yan
Performance of field cut preservatives above-ground and in ground contact exposures
2019 - IRG/WP 19-30742
Field cut preservatives are needed to protect cut ends and drill holes that expose the untreated interior of preserved wood. A series of field cut preservatives were assessed in ground contact and above-ground exposures. After 10 years in ground contact exposure, all of the untreated controls had failed or exhibited very advanced decay. In contrast, the copper naphthenate (2% Cu in mineral spirits...
R Stirling, D Wong
The development of a suitable fire retardant for Radiata pine and other species
2019 - IRG/WP 19-30744
The use of fire retardant chemicals, with the overarching aim of creating a safer environment is not a new one, however it is generally under-developed and is often afflicted with an image of environmental and health issues and misperceived high costs. There is an ever-increasing need and desire for effective fire retardancy in timbers to inhibit or suppress the combustion process. This is paramou...
B R Derham, M R Fortune