Your search resulted in 129 documents. Displaying 25 entries per page.
Dimensional Stability of Melamine Formaldehyde-Treated Southern Pine
2017 - IRG/WP 17-40774
The objective of this preliminary study was to evaluate the influence of different levels of melamine formaldehyde (MF) and curing cycle on the dimensional properties of southern pine. Thirty samples for each combination of treatment and curing regimen plus untreated controls and controls subjected to the same curing regimen were tested. Shrinkage/swelling coefficients showed that up to 60% ASE c...
H M Barnes, L S Sites, T S F A França, M G Sanders, F J N França
The Comparison of Weathering Resistance of New Generation Wood-Coating Systems
2017 - IRG/WP 17-40789
In this study, the performance of wood-coating systems containing different UV absorbers was evaluated in artificial weathering conditions. Acrylic-based resin containing three different UV absorbers was applied on oriental beech and scots pine surfaces. Weathering conditions were sustained for 84 days. After the weathering test, the change of color and roughness on the wood surface was measured t...
Ö Özgenç, S Durmaz
Moisture behaviour and biological durability of high performance flax fibre reinforced composites
2017 - IRG/WP 17-40803
For natural fibre composites in structural and load bearing applications long reinforcing fibres are required. Therefore, much research is performed on flax fibre reinforced composites to optimize them for high performance use. In most cases such research focuses on the mechanical properties, yet the assessment of moisture behaviour, dimensional stability and biological durability is an important ...
N Defoirdt, J Van den Bulcke, F Bensadoun, J Ivens, I Verpoest, J Van Acker
Aesthetic changes of coated thermally modified wood after artificial weathering
2017 - IRG/WP 17-40819
The thermal modification process affects the chemical configuration of the wood matrix improving some physical properties and durability. In addition, the distinctive dark tones of thermally modified timber increase the economic value of several light-coloured species. However, heat-treatment alters the substrates and it could influence in the application of coating products, necessaries to mainta...
R Herrera, J Sandak, E Robles, J Labidi
UV-curable coatings developed for aesthetic and biological protection of wood outdoors
2017 - IRG/WP 17-40821
To avoid wood greying, dimensional variations, and degradation by biological agents wood is protected with preservation products and coatings when used outdoors. For some wood species used for cladding, a treatment with a preservation product is required, and is frequently additionally protected with a coating. In this study, Mäder Group developed a new UV-curable coating for outdoors application...
C Reynaud, A S Schuller, M Kutnik, L Podgorski
Markers of quality in self-bonded beech boards
2017 - IRG/WP 17-40820
A self-bonding phenomenon takes place when five layers of beech (Fagus Sylvatica L.) veneers are pressed at temperatures higher than 200ºC. If the pressing temperature between veneer surfaces reaches at least 225ºC during pressing and if the pressure applied is optimal, water-resistant bonds are formed between veneers. This study investigates the relation of thickness reduction (marker of compre...
C Cristescu, D Sandberg, O Karlsson
Multiscale modification on water resistance and dimensional stability of Populus cathayana by alkali lignin combined with heat treatment
2018 - IRG/WP 18-40826
The aim of this study was to enhance the water resistance and dimensional stability of fast growing wood by alkali lignin combined with heat treatment. Poplar (Populus cathayana) samples were first impregnated with alkali lignin solution and then subjected to heat treatment at 140, 160, and 180°C respectively for 2h. Properties of leachability, moisture adsorption and water absorption, contact an...
H Zhou, J Li, E Ma
Improvement of short rotation teak wood properties through thermal modification
2018 - IRG/WP 18-40842
Teak (Tectona grandis L.f) is one of the most popular tropical timber species. Nowadays, the source of long rotation teak is limited in the availability. Many wood processing industries use short rotation teak, which has lower quality especially in durability and dimensional stability. Heat treatment is an eco-friendly method improving dimensional stability and durability of wood. The objectives o...
L A Pratiwi, I W Darmawan, B George, A Merlin, C Gérardin, S Dumarçay, T Priadi, P Gérardin
Wood-Plastic Composites preservation against fire: Nanofillers as fire retardant alternative
2018 - IRG/WP 18-40843
The purpose of this study is to improve fire resistance of Wood-Plastic Composites (WPCs) by adding inorganic nanofillers. Indeed, the main components of WPC, namely wood and polymer are both flammable materials despite the fact that WPCs are used in the field of construction. The effect of nanofillers on fire retardancy of Wood-High density polyethylene Composites was studied with three nanofille...
D Ben Ammar, A Koubaa, S Migneault, H Bouafif
Wood Protection Through Diffusion: Dimensional Stabilisation with Amine Oxides
2019 - IRG/WP 19-30747
Wood is a phenomenal construction material. In addition to its great physical properties and its beautiful appearance, it possesses many environmental-friendly virtues like the sequestration of carbon dioxide. It is however subject to dimension changes when submitted to fluctuating moistures levels, which can lead to warps, cracks and the peeling of paints. Many water repellents can slow down the ...
S Pepin, P Blanchet, V Landry
Dimensional stability and decay resistance of montmorillonite- furfuryl alcohol modified wood
2019 - IRG/WP 19-40856
Poplar (Populus cathayana) wood was impregnated successively by organo-montmorillonite (OMMT; in concentration of 2%) and furfuryl alcohol (FA, in concentrations of 15%, 30% and 50%) in a two-step method to prepare OMMT-FA modified wood. The modified wood samples were characterized using X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). Moreover, wood physical and a...
L Zhang, J Cao
Potential Use of the Pigment from Scytalidium cuboideum and Chlorociboria aeruginosa as an UV-light Protection Additive in Oil Finishes
2019 - IRG/WP 19-40868
UV-light degradation of wood is one of the top reasons for consumer replacement of outdoor wooden structures. This type of degradation is seldom mechanical, and is instead often motivated by loss of aesthetics (graying). There are numerous commercial products available on the market that deal with this loss of color, many of which contain added pigments to ‘rejuvenate’ or ‘revitalize’ grey...
S M Vega Gutierrez, D W Stone, R He3, P T Vega Gutierrez, Z M Walsh, S C Robinson
Novel approaches for improvement of dimensional, photo- and thermal stability of wood through liquefied wood polyols impregnation
2019 - IRG/WP 19-40884
The major problems encountered in both indoor and outdoor utilization of wood are due photo instability and dimensional instability. The modification of Melia dubia wood for ultraviolet resistance and dimensional stability with liquefied wood has been carried out through impregnation method under solvent free conditions. The level of impregnation in modified wood was estimated by weight perc...
A Kumar, A John, T S Mehra
Alternative products enhancing dimensional stability comparing to conventional treated products in Japan
2019 - IRG/WP 19-40885
The Act on the Promotion of the Utilization of Wood in Public Buildings (2010) in Japan has made a new stream of the utilization field of timber from housing constructions to larger scale non-housing constructions. After the act, the performance of dimensional stability in preservative treated products becomes more important factor than before. Therefore, various technologies have been developed, ...
K Yamamoto, D Tezuka, Y Sugai, S Maeda, I Momohara
Yellow birch fire-protection using polyelectrolytes complexes
2020 - IRG/WP 20-30755
Fire protection has been a major challenge in wood construction for many years. The demand for high-performance, environmentally friendly treatments respecting the physical and chemical characteristics of the material has been accentuated in recent years. Halogenated fire-retardant (FR) compounds were commonly used from the 70’s for their low-cost and high efficiency. They are able to form radic...
M Soula, F Samyn, S Duquesne, V Landry
Effect of a Water Repellent Treatment on Moisture Behavior of Three Australian Hardwoods: A Preliminary Report
2021 - IRG/WP 21-40921
Wood is inherently hygroscopic and will sorb moisture either directly from the atmosphere or via capillary action. Moisture can have marked effects on wood properties and repeated wetting and drying creates dimensional changes that lead to physical damage. Exposure to elevated moisture levels also increases the risk of fungal attack.
Wood preservatives have long been used to minimize the risk of ...
B Hassan, J J Morrell, K Wood
Effect of furfurylation treatment on the performance of three Canadian wood species
2022 - IRG/WP 22-40925
The demand for exterior wood siding is stagnating in North America, partly due to the perception of consumers, architects and contractors regarding their durability and maintenance. Improving attributes such as the dimensional stability of wood is therefore necessary to make it more attractive to consumers. This project aims to assess the performance of Canadian species; white spruce (Picea glauca...
G Boivin, D Schorr
Steam Pre-conditioning Treatment Prior to Acetylation: Impact on Dimensional Stability, Moisture Response Behaviour, and White-Rot Fungal Resistance of Hevea brasiliensis and Mitragyna ciliata Wood
2022 - IRG/WP 22-40930
The effect of steam pre-conditioning treatment on the dimensional stability, moisture response behaviour, and durability against white-rot fungus P. chrysosporium of acetylated Hevea brasiliensis and Mitragyna ciliata wood species were assessed. Defect-free specimens of both species from the top, middle, and base positions were selected, prepared according to ASTM D143-09 & ASTM D-2017 standards a...
E Uchechukwu Opara, J Mayowa Owoyemi, J Adeola Fuwape
Effect of nano-particle characteristics and concentration on UV protection of timber: A field exposure test
2022 - IRG/WP 22-40941
Wood has a well-known susceptibility to ultra-violet light degradation, leading to premature replacement. A variety of products have been developed to protect against this damage, but most provide less than 12 months of protection and must be regularly reapplied. Developing improved coatings would help reduce wood losses and reduce maintenance costs. Nano-particles have a variety of attractive pro...
T Yi, J J Morrell
Influence of weathering of wood surfaces before and after treatment with iron(II) sulphate
2023 - IRG/WP 23-30786
Outdoor wood is exposed to various factors that cause the wood to grey or age. The ageing processes can vary greatly depending on the exposure. Parts of the wood that are not exposed to external factors, e.g. under the eaves, are less exposed and the ageing process is therefore slower. This can be accelerated by solutions based on iron ions. In this way, the wood greys quickly and evenly. However,...
B Lesar, M Humar, F Osvald
Outdoor performance of Tanalith® K treated timber: Dimensional stability and corrosivity towards metal fasteners
2023 - IRG/WP 23-30798
This study was carried out to investigate dimensional stability and corrosivity towards metal fasteners in radiata pine (Pinus radiata D. Don) treated with Tanalith® K to Hazard class 4 (H4) retentions in comparison with chromated copper arsenic (CCA) treated timber. For corrosion test, untreated and treated matched specimens were prepared from Australian-grown radiata pine, tested with mild stee...
G Rassam, J Hague, D Humphrey
Effect of impregnation modification treatment on properties of Paraserianthes falcataria wood
2023 - IRG/WP 23-40966
Modification treatment can improve the properties of wood, particularly those of fast-growing species. Paraserianthes falcataria, also known as batai, is a fast-growing species with low wood density. This species has piqued the interest of those involved in industrial wood processing as a promising alternative for construction. The aim of this study is to improve the dimensional stability of batai...
A S Yusoh, A S Boneka, M K Anwar U, S Salim, S H Lee
New wood-modification process based on grafted urethane groups: Durability of carbamamylated Scots pine (Pinus sylvestris L.) wood
2023 - IRG/WP 23-40974
Substituting commonly used toxic preservatives with wood modification treatments can make the wood material less prone to water and moisture uptake. This approach favours a more sustainable protection of wood against biodegradation. In this study, Scots pine sapwood was full-cell impregnated with an aqueous solution of urea (30%), dried at 40°C for 24h, and subsequently heat-treated at 150°C for...
C-F Lin, O Myronycheva, O Karlsson, D Jones, D Sandberg
Enhancing UV resistance and decay resistance of wood by nanoparticle dispersed linseed oil nanoemulsion
2024 - IRG/WP 24-20706
Enhancing increasing demand for eco-friendly and cost-effective wood coatings and preservatives has led to the development of water-borne formulations and use of non-toxic and natural materials such as vegetable oils and waxes. The aim of this study was to improve the UV resistance and decay resistance of wood by nanomaterial dispersed linseed oil emulsions. Highly stable nanoemulsions of linseed ...
R Bansal, R Kumar, K K Pandey
Surface treatment of cross-laminated timber to improve water repellency and UV resistance
2024 - IRG/WP 24-20716
Cross-laminated timber (CLT) has emerged as a revolutionary building material, offering a sustainable alternative to traditional construction methods. By layering and bonding multiple layers of wood at right angles, CLT creates a robust and versatile structural element capable of supporting significant loads while promoting eco-friendliness and design flexibility. However, despite its numerous adv...
M Chen, S Uphill, J Hilsenbeck, A Hughes