Your search resulted in 161 documents. Displaying 25 entries per page.
Effect of Furfurylation on Shear Strength of Bond Line and Screw Withdrawal Resistance of Beech and Fir Wood
2016 - IRG/WP 16-40757
The aim of this study was to investigate the effects of furfurylation on shear strength of bond line and screw withdrawal resistance of beech (Fagus orientalis) and fir (Abies alba) species. In this regard, specimens with two different values of furfurylation i.e. low (fir 14% and beech 20%) and high (fir 38% and beech 65%) levels were prepared and evaluated in comparison with untreated specimens....
A Talaei, H Abdolzadeh, M Saleh Zare
Impact of heat treatment on physico-mechanical properties of torrefied Antholceistha djalonensis wood
2017 - IRG/WP 17-40811
Thermal modification at relatively high temperatures is an effective method to improve the dimensional stability and mechanical properties of wood. This study was carried out to investigate the impact of heat treatment on the physic-mechanical properties of torrefied Anthocleistha djalonensis wood. Thirty nine defect-free specimens of dimensions 20 mm × 20 mm × 60 were prepared for the determina...
E A Iyiola, B Olufemi, J A Fuwape, J M Owoyemi
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Experimental study on compressive strength performance of cross laminated timber with biodeterioration damage
2019 - IRG/WP 19-40883
The mass timber construction has attracted attention around the world. The reasons are due to the environmental impacts and the potential of the strength performance and quantity of the wood. Nowadays, CLT is one of the most important materials for the timber constructions. If we use CLT as a building material, we should consider the biodegradation risk for long time use. From an estimation of fut...
T Mori, Y Otsubo, R Inoue, M Ikeda, K Kambara, W Ohmura
Estimation of residual compressive strength on cross laminated timber with biodeterioration damage
2021 - IRG/WP 21-40918
CLT is susceptible to biodeterioration such as fungal decay and termite attack during long-term use for buildings. It is necessary to know the residual strength performance of biodegraded CLT for estimating future performance and aging of CLT. In this study, compression tests of CLT damaged by brown rot fungi and termites were conducted to clarify the relationship between residual strength and mas...
R Inoue, T Mori, K Kambara, W Ohmura
Make do and mend: Re-using timber in Smithfield Market
2022 - IRG/WP 22-50371
Historic buildings are part of our built environment. They are a record of how construction and use of materials have evolved and provide excellent opportunities for regeneration of urban areas. Moreover, re-using these buildings and as much of the material within, contributes to the Green Revolution.
Currently, there is tremendous growth in green construction and as Bob Dylan once said, “the t...
J R Williams
A simple method for assessing the effects of lyctid beetle attack on longitudinal compressive strength of spotted gum sapwood
2023 - IRG/WP 23-20700
Lyctid beetle attack is commonplace in a significant proportion of spotted gum utility poles that are air seasoned prior to chromated copper arsenate (CCA) treatment. While this damage is allowed, there are no reports quantifying the effects of the beetle galleries on pole properties. Full scale testing would require substantial quantities of poles in order to obtain a range of degrees of damage....
M Powell, J J Morrell
Estimation of single shear strength performance of screw joints with decayed wood
2023 - IRG/WP 23-40968
In order to use existing wooden structures for a long term, it is necessary to evaluate appropriately the damage degree of bio-deterioration of the structural performance including the members and joint systems. As one for them, it is necessary to estimate more accurate the single shear strength performance of screw joints with decay. Therefore, we proposed the model considering the yield strength...
R Inoue, K Tanaka, T Mori
Effect of incised pattern on flexural strength of CLT
2023 - IRG/WP 23-40993
As a study aimed at developing preservation methods suitable for CLT, investigations have been carried out using “deep penetration treatment”. This treatment method was originally developed as a treatment method for sawn lumber and glulam used as sill members. In the treatment, materials are incised using specially designed blades and immediately sprayed with an oil-based wood preservative. Th...
T Mori, R Takanashi, T Miyauchi, Y Ohashi, S Isaji
Relationships between deterioration part and structural performance in wooden houses
2023 - IRG/WP 23-50376
Based on the survey examples, there are four patterns of deterioration that tend to occur in plywood bearing walls of wooden houses in Japan. The first is a pattern in which wall is in a whole deterioration. It is a no damage wall or test specimen. The second is a pattern in which only the sill is deteriorating. It is caused by moisture or termites from ground to the base. In addition, there is a ...
Y Ota, H Ishiyama, S Okamoto
Manufacturing of bamboo hybrids with high strength, superior fire retardancy, and dimensional stability
2024 - IRG/WP 24-30808
Bamboo, renowned for its rapid growth, high strength-to-weight ratio, and eco-friendly attributes, has found extensive use in decorative building materials and glue-laminated beams. However, the inherent challenges of dimensional instability and flammability in natural bamboo restrict its broad application. This research introduces a range of environmentally friendly techniques aimed at producing ...
W He, Rui Wang, W Li, G Hu, T Singh, Q Fu