Your search resulted in 1012 documents. Displaying 25 entries per page.
Using an accelerated laboratory method to evaluate Aureobasidium pullulans colonization on painted surfaces and underlying wood substrate
2012 - IRG/WP 12-20480
Mold growth on painted surfaces can lead to premature paint film failure and is unsightly. Aureobasidium pullulans has been identified as a major cause of black stain on surfaces painted with acrylic or latex paints. In this study, an accelerated laboratory method developed by Zabel and Horner (1981) was used with modifications to the type of agar used and sample evaluation methods. A study was ...
C Schauwecker, L Burns, A Preston
Supercritical impregnation of wood with siloxane
2012 - IRG/WP 12-30595
This paper describes the effect of supercritical impregnation with siloxane on the water repellency of Scots pine (Pinus sylvestris) sapwood samples. Samples were impregnated with a low amount of siloxane dissolved in supercritical carbon dioxide using isopropanol as a co-solvent. Siloxane retention (i.e. weight percent gain (WPG)) of the treated samples was 1.3 % (w/w) as found by mass balance. T...
A Kjellow, F Imsgard, J Fernandes, O Henriksen, E Klaassen, R Wagner, J Delis
Stabilization of IPBC in wood through the use of organosilicon compounds
2012 - IRG/WP 12-30597
The aim of the research was to increase durability of wood treated with 3-Iodo-2-propynyl butylcarbamate (IPBC). The study used a blend of silanes. Biological examination against microfungi was performed to determine resistance of Scots pine wood treated with the tested formulations. Chemical analysis by the Electrospray Ionization Mass Spectrometry (ESI-MS) of water extracts from the leaching per...
B Mazela, W Perdoch
Comparison of exterior performance of two coating systems based polyurethane applied Pinus sylvestris L. and Picea orientalis L. wood
2012 - IRG/WP 12-40588
Some surface changes in sapwood and heartwood of two species before applying clear-coating were characterized after accelerated weathering time. Wood specimens covered with two types polyurethane (PU) films were also observed in accelerated weathering exposure. In this study, changes on the wood surface were compared of between wood specimens covered with two types polyurethane (PU) films after ir...
Ö Özgenç, Û Cafer Yıldız
Tar-oil uptake vs time in immersion treatment of short pine posts: A simple technique applicable to rural communities of Papua New Guinea
2012 - IRG/WP 12-40608
Pinus caribaea and Araucaria cunninghamii logs ca. 100 mm in diameter were shortened to lengths 25-30 cm, conditioned to at/below fibre saturation point (FSP) for immersion/dip treatment using a hot- and- cold bath open- tank process. Before oven-drying and subsequent treatment, individual test specimens were numbered, their green weights and volumes, and dry weights recorded for basic density, vo...
B K Gusamo, R Tulo
Differences between heat treated Pinus pinaster heartwood and sapwood
2012 - IRG/WP 12-40617
Heat treatment is a well known process to improve the durability and dimensional stability of less noble woods. The treatment can be applied for heartwood unlike the traditional treatments based on impregnation due to the difficulty of impregnating heartwood.
Pure sapwood and pure heartwood samples were treated in an oven at 190ºC and 200ºC for 2h, 4h and 6h. Dimensional stability, measured a...
B Esteves, L Nunes, I Domingos, H Pereira
Inhibitory extractives or nutrients? Mould growth on coated heartwood and sapwood of Pinus sylvestris and Gleditsia triacanthos
2013 - IRG/WP 13-10806
Sometimes mould fungi grow over weathered coated sapwood, whereas the coated heartwood is not colonised. Two factors may be responsible for these differences: Either the larger content of nutrients in the sapwood, or the content of biocidal extractives in the heartwood. In this study the factors for the difference in mould growth on coated heartwood and sapwood of Pinus sylvestris (Scots Pine) and...
D Lukowsky, N Buddruhs
Extraction and analysis of DNA from green and seasoned timber as basic methods for determination of wood species and origin
2013 - IRG/WP 13-20523
Against the background of the European timber trade regulation EUTR, commenced to law by March 2013, the determination of wood species and tracing of its origin is getting a great importance. A promising approach for establishing fast and reliable tracking systems for wood products is DNA analysis. A critical point is the extraction of analysable DNA from the wood and its lignified cell walls. Thu...
K Jacobs, H Mende, W Scheiding
Cell wall properties of softwood deteriorated by fungi: combined chemical analyses, FT-IR spectroscopy, nanoindentation and micromechanical modelling
2013 - IRG/WP 13-20527
Mechanical properties of wood are determined by its inherent hierarchical microstructure, starting at the nanometer scale, where the elementary components cellulose, hemicelluloses, and lignin build up the wood cell wall material. Fungi cause degradation and decomposition of these components and, thus, alter the mechanical properties of wood. The aim of this study is to gain new insight into these...
L Wagner, T K Bader, K de Borst, T Ters, K Fackler
Antifungal properties and bonding of menthoxymethylimidazolium ionic liquids with Scots pine wood
2013 - IRG/WP 13-30627
Antifungal activities of five chiral ionic liquids - menthoxymethylimidazolium derivates against brown-rot decay fungus (Coniophora puteana), white-rot decay fungus (Trametes versicolor) and blue-stain fungus (Sclerophoma pithyophila) were determined using screening agar-plate method. Results from antifungal tests revealed that 1-butyl-3- menthoxymethylimidazolium chloride exhibited the stronges...
J Zabielska-Matejuk, J Feder-Kubis, A Stangierska
Protective effectiveness of antifouling coatings for wooden boats in the Northern Adriatic Sea
2013 - IRG/WP 13-40634
There are various conventional biocide containing antifouling coatings and some more environmentally friendly paints for boats on the market. However, the question of their performance in accordance with the manufacturers’ statements or guaranties arises. The aim of our preliminary investigation was to state which type of antifouling coating exhibits better effectiveness against fouling organism...
M Petrič, M Humar, J Adamek, B Kričej
Resistance to Decay Fungi of Scots Pine Impregnated with Natural and Chemical Preservatives
2014 - IRG/WP 14-30650
In this study, heart-wood and sap-wood specimens of the Scots pine which is naturally grown in Turkey were treated with natural (valex) and some chemical preservatives such as CCA - C (Copper / Chrome / Arsenic), CBA - A (Copper / Boron / Azole). The wood protective efficacies of these preservatives were investigated by means of fungi decay test (EN 113).
As a result of the study it was found t...
S Yildiz, U B Şimşek
Chemical composition of extractives of different wood compartments of Pinus merkusii and their potential implication in wood durability
2015 - IRG/WP 15-10841
Amounts and nature of extractives differ strongly according to the compartment of wood and to the nature of the wood species. Previous studies reported that knotwood of several European Pinus sp. contains extractives contents much higher than stemwood consisting mainly of lignans which may find valuable applications in cosmetic, nutraceutic or pharmaceutic sectors. Different explanations have been...
A Wijayanto, S Dumarçay, R Kartika Sari, W Syafii, P Gérardin, C Gérardin-Charbonnier
Influence of artificial and natural weathering on water exclusion efficacy of wood
2015 - IRG/WP 15-20559
Water exclusion efficacy (WEE) is one of the most important properties of wood that contributes to the overall performance of naturally durable wood species in outdoor above ground applications. WEE is in strong correlation with moisture dynamics of wood, its hydrophobicity and can indicates susceptibility against wood decay fungi. Despite of the importance of this parameter, WEE is not completely...
M Žlahtič, M Humar
Evaluation of color and gloss in decorative applied to cases of Pinus radiata wood impregnated (D. Don) copper type C azole micronized
2015 - IRG/WP 15-20571
Six treatments (one control and five decoration coatings) were applied to radiata pine wood treated with micronized copper azole (uCA-C), for outdoor use (R3) at a rate of 3.08 kg/m3 retention (T2). One decoration coating was applied before impregnation treatment: Prestain P (T3), and two, were applied in mixture with the uCA-C preservative Black Cylinder (T5) and Red Cylinder (T4). Two varnish we...
R Garay, M Inostroza
Search for an anti-sapstain treatment for fresh radiata pine wood in compliance with European BPD norms: Field Tests
2015 - IRG/WP 15-30673
In response to the impending restrictions on the use of pesticide active ingredients developed to control the staining of fresh wood, as a result of regulation issued in 2009 by the European Union, a project was proposed to test an alternative anti-sapstain treatment that meets both the European restrictions and the performance required for an export-quality radiata pine fresh wood treatment. A se...
P Montes C, T Hanke W
Formation of biofinishes on outdoor exposed wood; the impact of wood-oil combination and geographical location
2016 - IRG/WP 16-10864
Growth of dark moulds enables the use of a decorative and protective biofinish for wood, showing advantages compared to traditional wood-coatings in terms of sustainability and self-repair. Based on the formation of a uniform mould covering on oil treated wood during outdoor exposure, the utilisation of a biofinish is in development. Basic information is lacking on the correlation between exposure...
E J van Nieuwenhuijzen, L Ross Gobakken, M F Sailer, R A Samson, O C G Adan
A Comparison on Penetration of Silica Sol in Scots pine and Southern pine wood
2016 - IRG/WP 16-40722
Penetration is one of the most important issues to be considered in wood impregnation with various kinds of chemicals in liquid form. Scots pine (Pinus sylvestris) and Southern pine (Pinus spp.) are two frequently used wood species for treatment, such as preservative treatment. With the development of treating systems, some micro- or nano-sized aqueous modifiers are emerging in the market, which p...
Mingyang Sun, Jinzhen Cao
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Thermally modified timber treated with methacrylate
2018 - IRG/WP 18-40849
Thermally modified timber (TMT) from Scots pine sapwood similar to Thermo-D quality was impregnated with methacrylate resin by the hot-and-cold method and subsequently cured at elevated temperatures. The results showed that methacrylate resin could be used to reduce colouring of painted TMT wood during accelerated weathering probably by hindering the migration of extractives. The resin itself did ...
O Karlsson, O Myronycheva, DJones, D Elustondo, D Sandberg
The development of a suitable fire retardant for Radiata pine and other species
2019 - IRG/WP 19-30744
The use of fire retardant chemicals, with the overarching aim of creating a safer environment is not a new one, however it is generally under-developed and is often afflicted with an image of environmental and health issues and misperceived high costs. There is an ever-increasing need and desire for effective fire retardancy in timbers to inhibit or suppress the combustion process. This is paramou...
B R Derham, M R Fortune
The anti-weathering mechanism of extractives in thermally modified Scots pine
2019 - IRG/WP 19-40880
Results from the electron spin-resonance spectroscopy (ESR) analysis indicated that thermally modification of wood can inhibit the generation of phenoxyl radicals during UV irradiation and consequently lead to the increase of the color stability of wood. In order to clarify the evolution and role of extractives in thermally modified wood during the process of weathering, the compositions of aceton...
H Shen, J Cao
Terrestrial laser scanning (TLS) – a potential tool for improved utilisation of the natural durability of Scots pine for solid wood products
2019 - IRG/WP 19-50358
The natural durability of sapwood of most species is generally low, while heartwood can be more resistant to biodeterioration. For the sawmill industry various lumber products require certain diameters and lengths of the logs in addition to requirements for wood properties. When utilising the heartwood, it is therefore important to acquire information already in the forest about which trees that c...
P-O Flaete
Different levels of acetylation lead to groupwise upregulation of non-enzymatic wood degradation genes of Rhodonia placenta during initial brown-rot decay
2020 - IRG/WP 20-10958
Rhodonia placenta, often used as a model fungus to represent brown rot fungi, uses a two-stepped degradation mechanism to degrade wood. Regarding the overcoming of wood protection systems the initial degradation phase seems to be the crucial point. A new laboratory test enables the separation of the non-enzymatic oxidative and the enzymatic degradation phases, which has previously been proven chal...
M Kölle, R Ringman, A Pilgård