Your search resulted in 964 documents. Displaying 25 entries per page.
Hydrophobic characteristics of pyrolysis oil
2008 - IRG/WP 08-30458
Hydrophobic behavior of pyrolysis oils obtained by pyrolysis of Scots pine wood (Pinus sylvestris L.) by using extruder type pyrolyzer at 450, 550 and 600 ºC was the objective of the study. Sapwood specimens (15×25×50 mm along the grain) were impregnated with the obtained pyrolysis oils by full- and empty cell treatment.
The results indicated that wood impregnated with the studied pyrolysis o...
A Temiz, M Hakki Alma, N Terziev
Validity of above ground testing according to ENV 12037
2008 - IRG/WP 08-20379
The standard ENV 12037 for testing of treated and untreated wood (lap-joint) exposed above ground
was issued in 1996 by The European Committee for Standardization. A draft for the development of the standard was presented by CEN-TC 38/WG 25/DOC N 076 in 2002. For a test to become valid the median rating of decay for untreated control replicates (Scots pine sapwood) must be equal or greater than ...
Ö Bergman, U Råberg, N Terziev
Spruce and pine heartwood treatment by means of microwave radiation
2008 - IRG/WP 08-40411
An easier penetrability and a more even uptake of wood protection agents is aimed for the two most common wood species in Europe, namely Norway spruce (Picea abies) and Scots pine heartwood (Pinus sylvestris), particularly when there is a great difference in absorption behavior of sapwood and heartwood. Microwave conditioning can improve permeability, reduce density and heat conductivity and chang...
A Treu, H Rieche, H Militz
Spruce and pine heartwood treatment by means of microwave radiation
2008 - IRG/WP 08-40411
An easier penetrability and a more even uptake of wood protection agents is aimed for the two most common wood species in Europe, namely Norway spruce (Picea abies) and Scots pine heartwood (Pinus sylvestris), particularly when there is a great difference in absorption behavior of sapwood and heartwood. Microwave conditioning can improve permeability, reduce density and heat conductivity and chang...
A Treu, H Rieche, H Militz
Resistance against basidiomycetes of 1,3-dimethylol-4,5-dihydroxy ethylene urea (DMDHEU)-modified plywood of Pinus sylvestris
2008 - IRG/WP 08-40398
Plywood produced with rotary-cut veneers of Pinus sylvestris impregnated with a solution of 1.3 M 1.3-dimethylol-4.5-dihydroxyethyleneurea (DMDHEU) and glued with a phenolic resin (Prefere 4976 DYNEA) were inoculated with Coniophora puteana, Coriolus versicolor and Pleurotus ostreatus, following the European standard ENV 12038. The specimens were leached following European standard EN 84. The re...
A Dieste, A Pfeffer, S Bollmus, H Militz
Variations of Furfuryl alcohol and Wolmanit CX-8 treatability of pine sapwood within and between trees
2008 - IRG/WP 08-40421
The variations on the ratio of filling (RoF) were investigated on Norwegian grown Scots pine (Pinus sylvestris). The samples were taken from 10 different stands in south-east Norway, and treated with furfuryl alcohol and a copper-containing wood preservative. Both within tree variations, between tree variations and variations between stands were investigated for significant differences. Factors li...
E Larnøy, S Lande, G I Vestøl
Cantilever bending test of furfurylated poles
2008 - IRG/WP 08-40424
Ten, 8 m long poles of Scots pine (Pinus sylvestris) were treated with furfuryl alcohol to a WPG of approximately 40 %. A bending test was performed according to the principles in the draft European standard for wooden poles, prEN 14229 - Structural timber - Wood Poles for overhead lines. The bending strength and stiffness (MOE) for the poles tested were compared to an earlier study by the Swedish Wood Preservation Committee. In the latter study untreated, CCA-treated, ammoniacal Cu-PCP treated and creosoted poles were tested in bending. These types of poles were considered not to differ in strength and stiffness. The results of the furfurylated poles fit well with the results from the previous study. The bending strength and MOE values obtained are compared to the upper and lower 95-percentile values of the results from the previous study and all poles treated with furfuryl alcohol fit within this interval.Thus, this study indicates that a treatment with furfuryl alcohol does not result in a decrease of strength or stiffness. Further testing with a larger population of poles is necessary in order to get a statistically reliable result. In addition to further demonstration of the durability, the
treatment process must be optimised to ensure full sapwood penetration and measures have to be taken to avoid the serious cracking observed in this trial before furfurylation can be considered for treatment of Pinus sylvestris poles.
R Ziethén, J Jermer, A Clang
Control biológico de la mancha azul en madera aserrada de Pinus radiata D. Don.
2008 - IRG/WP 08-10681
Radiata pine wood is highly susceptible to the attack of sapstaining fungi promoting a discoloration which results in important economical losses. The use of chemicals, a customary procedure to prevent its occurrence is becoming nowadays, due to environmental concern, a more questionable practice. The biological control of blue stain fungi with albino isolates of the Ophiostoma genera appear to ...
J Navarrete, A Segura, P Martínez, R Vera, C Segovia, P Herrera, L Reyes, D McNew, T C Harrington, R L Farrell, J M Thwaites, B Held, R A Blanchette
Estudio comparativo entre postes de Eucalyptus saligna Smith, Pinus caribaea Morelet (pino macho) y Hormigón
2008 - IRG/WP 08-40436
As consequence of the Energy Revolution and the amplification of the communication networks, Cuba carries out significant expenditures of foreign currencies in the import of public service posts. It is presented in this work a synthesis of the current problem in Cuba of the public service posts (PSP), since as answer to the stocks of improvement of the national Electric System, the demand of this ...
C Sosa Suárez, I D Velázquez Viera, K Manzanares Ayala
Chemical modification of Scots Pine Sawdust by mixed anhydrides
2008 - IRG/WP 08-40439
By making react mixtures containing acetic-fatty anhydrides on Scots pine sawdust (SPS) without any solvent or catalyst; we synthesized mixed acetic-fatty esters of SPS. Such mixtures were synthesized by reaction between a carboxylic acid and acetic anhydride. These mixtures were obtained after reaction of acetic anhydride and a fatty acid that yields at equilibrium a mixture of five compounds: ac...
J Peydecastaing, E Borredon, S El Kasmi
Durability and fungal colonisation patterns in wood samples after six years in soil contact evaluated with qPCR, microscopy, TGA, chitin- and ergosterol assays
2009 - IRG/WP 09-20402
There is a need to establish new objective and sensitive methods for early detection and quantification of decay fungi in wood materials. Molecular methods have proven to be a useful tool within wood protection issues, however, this field is still poorly explored and so far relatively few have used these methods within the field of wood deterioration. Among the techniques used in the indirect quan...
A Pilgård, G Alfredsen, I Børja, C Björdal
European House Borer Hylotrupes bajulus Linnaeus in Western Australia: the anatomy of an eradication program
2009 - IRG/WP 09-20403
In January 2004, European house borer (EHB) Hylotrupes bajulus Linnaeus was detected in Perth, Western Australia. A containment program was set up and expanded to a full eradication campaign in 2008. The program is projected to eradicate EHB by 2021. This paper describes research work and assumptions on the biology and behaviour of EHB in Western Australia, surveillance and control methods, commun...
M Grimm, R J Cunningham, M Castalanelli, D Collins, L Vagg
Microscopy evaluation of microbial decay patterns in wood stakes after 6 years in soil contact
2010 - IRG/WP 10-10715
Most studies on wood modification have so far been concerned with service life predictions rather than investigating the decay protection mechanism. Very little is known about the mode of action of these new treatments and about the strategies used by wood degraders in order to utilize the wood material despite a treatment. Access to such knowledge would allow further modification and improvement ...
A Pilgård, C G Björdal
Evaluation of ACQ-D treated Chinese fir and Mongolian Scots pine with different post-treatments after 20 months of exposure
2010 - IRG/WP 10-30530
The performance of alkaline copper quat-type D (ACQ-D) treated Chinese fir (Cunninghamia lanceolata Hook.) and Mongolian Scots pine (Pinus sylvestris Linn. var. mongolica Litv.) stakes after 20 months exposure in Chengdu and Guangzhou of southern China were evaluated according to AWPA standard E07-07. The ACQ-D treatments used two concentration levels (0.5 and 1.0%) and four different post-treatme...
Lili Yu, Jinzhen Cao, Wei Gao, Haitao Su
Treatment of Scots pine wood with oil in water and water in oil emulsion systems: Effects on boron leaching and water absorption
2010 - IRG/WP 10-30535
The aim of this study was to investigate the water absorption and water repellent efficiency of oils and oil water emulsions [oil-in-water (O/W) and water-in-oil (W/O)] and possibilities of reducing the amount of boron leaching from treated wood. Scots pine wood samples treated with waste or sunflower oil and water formulations contained 3%BA. The level of water absorption and water repellent effi...
E D Tomak, Ü C Yildiz, A Can
The kinetics of catalytic acetylation of Pinus radiata (D. Don) using conventional and microwave heating
2010 - IRG/WP 10-40485
This study outlines the effect of catalyst and microwave heating on the degree of acetylation in radiata pine. Samples of radiata pine sapwood were impregnated with potassium acetate (KAc) dissolved in two different solvents (water and methanol). Impregnated samples were dried and subjected to acetic anhydride loading followed by conventional and microwave heating. The degree of acetylation was ev...
A Kumar Sethy, P Vinden, G Torgovnikov, S Przewloka
Fungal decay resistance and mechanical properties of plywood panels made from maritime pine (Pinus pinaster) and bonded with cornstarch-quebracho tannin-phenol formaldehyde adhesive
2010 - IRG/WP 10-40490
The aim of this work is to demonstrate the performances of cornstarch-quebracho tannin-based resins designed as adhesive in the plywood production. In this way, the cornstarch and quebracho tannin was introduced in the classic adhesive formulation in order to supply a part of phenol-formaldehyde (PF). In order to evaluate the mechanical performances of optimal cornstarch-quebracho tannin-PF, plywo...
F Charrier, A Moubarik, A Allal, A Pizzi, B Charrier
Biological degradation of acetylated wood after 18 years in ground contact and 10 years in marine water
2010 - IRG/WP 10-40522
This paper addresses the resistance to biological degradation of acetylated wood.
Firstly, it presents results from an EN 252 test after 18 years’ exposure. The test is still running in Nordic NWPC test fields, Simlångsdalen in Sweden and Viikki in Finland. Results from this test were presented after 5 years’ exposure ( IRG/WP 97-30139), and showed that the resistance of acetylated wood wit...
P Larsson Brelid, M Westin
Testing of decay resistance of sapwood and heartwood of thermally modified Scots pine and Norway spruce
2010 - IRG/WP 10-40523
Thermal modification at elevated temperatures changes the chemical, biological and physical properties of wood. One of the main targets of thermal modification is to increase the biological durability and decay resistance of wood. Although the effects of thermal modification on wood have been widely studied, the significance of sapwood and heartwood on the resistance of thermally modified wood has...
H Viitanen, S Metsä-Kortelainen
Combined Effect of Boric Acid and Waste Oil Treatment on Boron Leaching
2010 - IRG/WP 10-50268
In this study it was aimed to investigate the boron leaching amounts in Scots pine wood samples treated with boric acid (BA) and waste oil (WO) alone or by dual treatment. The level of water absorption and water repellent efficiency were determined with cyclical wetting tests, total of 336 hours. Wood samples that have both covered and uncovered transversal section were impregnated with 3% boric a...
Ü C Yildiz, E Dizman
Basidiomycete colonization of Scots pine sapwood quantified by qPCR and TGA
2011 - IRG/WP 11-10750
Scots pine (Pinus sylvestris L.) is an important softwood species in Northern Europe and is frequently used as material for various wood protection systems. In Europe, EN 113 is the standard basidiomycete laboratory durability test method, using mass loss as evaluation criteria. In this paper quantitative real-time PCR (qPCR) and thermogravimetric analysis (TGA) was used to characterize coloniza...
G Alfredsen, S Bollmus, T K Bader, K Hofstetter
Sample Origin Influencing the Leachability of Wood Preservatives
2011 - IRG/WP 11-20474
The aim of this study is to see if the raw material influences fixation and leachability of wood preservatives. Moving towards more eco-friendly and –concious society, the wood industries must adjust itself to new rules and regulations. Greener solutions in wood protection are being tested and introduced, older systems are being improved, but questions still arise concerning some elements curren...
K Kängsepp. E Larnøy, P Meier
Biological and mechanical performances of particleboard panels made from maritime pine (Pinus pinaster) and glued with cornstarch-mimosa tannin-urea formaldehyde adhesive
2011 - IRG/WP 11-40542
The objective of this work was to demonstrate the utility of cornstarch-mimosa tannin-based resins designed for application as an adhesive in the particleboard production. Bond qualities of cornstarch-mimosa tannin- urea formaldehyde (UF) (10:4:86, weight ratios) resins and commercial UF resin were assessed by using an automatic bonding evaluation system, prior to production of particleboard panel...
A Moubarik, F Charrier, A Pizzi, A Allal, B Charrier
Treatability variation of scots pine heartwood from Northern Europe
2011 - IRG/WP 11-40563
Scots pine (Pinus sylvestris L.) is one of the most common construction materials for general exterior applications in northern Europe. It has a wide natural geographical distribution, a good availability and it is low-priced compared to other materials. According to EN 350-2 Scots pine heartwood is considered being “untreatable” and having durability class 3. This means that its durability co...
G Behr, E Larnøy, C-T Bues
Decrease of stiffness properties of degraded wood predicted by means of micromechanical modeling
2011 - IRG/WP 11-40570
Wood exhibits a highly anisotropic mechanical behavior due to its heterogeneous microscopic structure and composition. Its microstructure is organized in a strictly hierarchical manner from a length scale of some nanometers, where the elementary constituents cellulose, hemicelluloses, lignin, and extractives are found, up to a length scale of some millimeters, where growth rings composed of earlyw...
T K Bader, K Hofstetter, G Alfredsen, S Bollmus