Your search resulted in 1048 documents. Displaying 25 entries per page.
Post-layup protection of mass timber elements in above ground protected exposures: 2-year results
2022 - IRG/WP 22-30766
Mass timber has seen increased use as a building material for low and mid-rise construction in recent decades. The durability of mass timber elements has not been fully examined and the effects of wood destroying organisms on this these materials merits attention. The effectiveness of currently labeled soil termiticides and passively applied biocides at post-construction or as remedial agents need...
M E Mankowski, T G Shelton, G T Kirker, J J Morrell
A novel wood preservation technology improving durability and water-related properties
2022 - IRG/WP 22-40926
A newly developed silicone oil (Archroma Management GmbH, Switzerland) was tested for wood modification purposes. Scots pine sapwood was treated with aqueous solutions of this silicone oil and showed a penetration of the modification agent into the wood cell wall. Both, biological durability and moisture-related properties, experienced significant improvements by the modification. Besides, the mod...
L Emmerich, H Militz, M Vila
Durability against fungal decay of sorbitol and citric acid (SorCA) modified wood
2022 - IRG/WP 22-40928
Most European-grown wood species are susceptible to biological degradation, specifically, they suffer from a poor resistance against wood-destroying fungi. Therefore, prior to outdoor exposure, wood has to be treated either by applying a protective coating on its surface or by full-volume impregnation with antifungal chemicals. However, due to environmental and health concerns, the most frequently...
K Kurkowiak, L Emmerich, H Militz
Environmentally Friendly Wood Modification based on Tannin-Furfuryl alcohol - Effect on stabilisation, mechanical properties and decay durability
2022 - IRG/WP 22-40929
Furfurylation is a well-known wood modification technology. This paper studied the effect of tannin addition on the wood furfurylation. Three kinds of dicarboxylic acids, adipic acid, succinic acid, and tartaric acid, as well as glyoxal as a comparing agent, were used to catalyse the polymerisation of furanic or tannin-furanic solutions during wood modification. Impregnation of furanic or tannin-f...
M Mubarok, E Azadeh, F O Akong, S Dumarçay, A Pizzi, C Charbonnier-Gérardin, P Gérardin
The Resistance of Some Commercially Thermally Modified American Hardwoods to Termites and Fungi
2022 - IRG/WP 22-40944
Thermally Modified Wood (TMW) is now being produced in the United States but there are few data on the durability of these materials. In this study, commercially-produced thermally modified yellow poplar (Liriodendron tulipifera), red maple (Acer rubrum), and white ash (Fraxinus americana) were evaluated for fungal and termite resistance. The resistance of the three TMW species against Gloeophyllu...
B Cortes, B Bond, A Taylor, J Lloyd
Effect of densification of Eucalyptus nitens and E. obliqua on moisture uptake, swelling, decay resistance, and fire performance
2022 - IRG/WP 22-40946
Some Australian Eucalyptus species that are abundantly available have low natural durability and poor resistance to fire. These same species are also extremely difficult to treat with preservatives or fire retardants using conventional pressure treatment methods due to a large proportion of refractory heartwood. The aim of this research was to understand whether thermo-mechanical densification had...
B Hassan, J J Morrell, F Wiesner, W Wu, B Belleville, K C Wood
Durability of thermotreated Pinus sylvestris and Eucalyptus nitens against wood decay organisms
2022 - IRG/WP 22-40949
One of the alternative treatments to avoid the application of biocides is thermal modification of wood, which increases the durability of wood against attack by wood decay organisms. The durability of Pinus sylvestris and Eucalyptus nitens thermotreated at 180 and 212 ºC, was studied. The results show that thermotreatment against wood decay fungi in P. sylvestris is slightly more effective than i...
M T Troya, S M Santos, L Robertson, N Pérez-Molina, V Baños, A Dieste
Durability of thermally modified western hemlock lumber against wood decay fungi
2022 - IRG/WP 22-40954
The chemical modification of wood is gaining popularity as a treatment to increase wood durability in the United States. Further standardization and testing of thermally modified North American species is needed to optimize the production of thermally modified products from regionally available resources. This work measures the impact of thermal modification of western hemlock lumber durability ag...
G Presley, J Cappellazzi, I Eastin
Evaluation of Decay Resistance for the Larch Wood Heat-treated with Superheated Steam
2022 - IRG/WP 22-40956
Heat-treatment of wood is a process that involves applying heat ranging 160–260°C to improve its physico-mechanical properties and resistance against wood rot fungi. The level of the changes in the wood properties by heat-treatment differs depending on the temperature and duration of heat-treatment, as well as the types of heat transfer media used for heat-treatment. The heat-treatment on wood ...
Y Park, S-M Yoon, H Kim, W-J Hwang
Novel bio-based tannin/furfurylic alcohol thermosets: application to wood preservation
2022 - IRG/WP 22-40959
This project is integrated within the overall context of sustainable development and targets the valorization the wood industry by-products such as polyphenolic extractives, and in particular tannins. The objective targets the use of the same polymer used for production of tannin-furanic foams, but here for wood preservation to avoid the utilization of biocides. The aims is to the design of copoly...
C Gérardin-Charbonnier, E Azadeh, A Pizzi, P Gerardin
Biological durability for novel composites manufactured from green materials
2022 - IRG/WP 22-40960
Flax and Jute fabrics were used as reinforcements with polyester resin to form composite skins while poplar particleboard was used as a core for making composite sandwich structures by applying vacuum assisted resin transfer molding (VARTM) technique. Mechanical, physical, and biological properties of these novel green composite sandwich structures were evaluated. The results showed that the propo...
A S O Mohareb, A H Hassanin, A A Badr, K T S Hassan, R Farag
Assessment of the Material Durability and Structural Integrity of the Wooden Velodrome in Češča vas, Slovenia
2023 - IRG/WP 23-11012
Wood is a widely used material in the construction industry, and it has been utilized for thousands of years to create buildings and other structures. When wooden structures are designed, built, and maintained properly, they can be safe and long-lasting. Sports facilities, which provide athletes with a space to train, compete, and improve their abilities, are crucial in creating a strong and susta...
D Kržišnik, M Humar, B Lesar
Isolation of the microbiota from wood decay insects and some of their enzymatic activities
2023 - IRG/WP 23-11014
Wood decay organisms have the ability to degrade wood components (cellulose, hemicellulose and lignin) by enzymatic capacities, but these enzymes can belong to the proper organism, or to the associated microbiota. The identification of the microorganisms, as well as their role in the digestion of many substrates not always is very well known.
The wood decay insects produce big damages in wood str...
M T Troya, F Llinares, J Arranz, S Izpura-Luis, S M Santos, L Robertson
Morphological observation of wood at the early stages of decay in brown rot and white rot
2023 - IRG/WP 23-11020
Wood rotting fungi, the fungal species causing biodeterioration for wood building, are generally classified into white-rot, brown-rot and soft-rot fungi based on their decay modes. Since white-rot and brown-rot fungi are known to reduce wood strength significantly, it is important to clarify the mechanisms of their wood degradation. White-rot fungi reduce wood strength as the decay progress and de...
R Tsukida, T Hatano, Y Kojima, Y Horikawa, S Nakaba, R Funada, M Yoshida
Field durability testing of wood above ground - Part 1: 15 years’ experience with the Bundle method
2023 - IRG/WP 23-20695
A ‘jack of all trades’ method for above-ground wood durability testing has been sought for decades, but until now no method has found its way into standardization. The method of choice shall be applicable for untreated and treated wood – ideally also for wood composites. It shall be reproducible, objective, fast, easy, and inexpensive. Finally, it shall provide high predictive power.
This s...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Field durability testing of wood above ground - Part 2: The full guideline of the Bundle method
2023 - IRG/WP 23-20696
To determine the biological durability of wood above ground, numerous approaches for test methods have been pursued and tried out in the field in the past. So far, no method has managed to find its way into a European standard. During the last 15 years, experience with the Bundle method has been gained. As described in Part 1 of this paper, the method is recommended as a suitable tool for determin...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Laboratory durability testing of preservative treated wood products – first attempts and observations
2023 - IRG/WP 23-20697
In the past, durability classes (DC) had been assigned to wood species, sometimes also to homogenously modified wood-based materials such as thermally modified wood. More recently, some standards allow for classifying the biological durability of chemically modified wood, preservative treated wood and wood composites. Even treated products may be subject to durability classification, but necessary...
C Brischke, M Sievert, M Schilling, S Bollmus
Geopolymer as a fixation method for tannin-based wood preservatives
2023 - IRG/WP 23-30774
This study aims to test if a second step impregnation with a geopolymer solution can fix Colatan GT10, a commercial extract rich in tannins, to wood, reducing their leaching and improving their performance as wood preservatives. Scots pine sapwood specimens of 40×10×5 mm3 were impregnated with Colatan GT10 tannin mix, geopolymer, and as combined treatment Colatan GT10 with subsequent geopolymer ...
Y M López-Gómez, A Barbero-López, A Haapala
A six-year ground proximity trial of TRU-CORE treatments at Innisfail, Queensland
2023 - IRG/WP 23-30775
This article describes an H3 (above ground outdoor) ground proximity field trial that compares the performance against decay fungi of TRU-CORE (also known as the Buffered Amine Oxide Enhancement System) Copper Quat (CQ) with CCA and commodity Alkaline Copper Quat (commodity-CQ) treatments, all in Pinus radiata. The retentions achieved reflected commercial practice, where higher mean retentions are...
L Cookson
Suitability of boron preservative treatment of minor species as framing in New Zealand buildings
2023 - IRG/WP 23-30778
The inclusion of alternative species to radiata pine, predominantly exotic species, in the building code (NZS 3602) raises questions as to whether they require preservative treatment and, if so, whether they can be adequately treated using current industry processes.
Early research with boron indicated that the dip/diffusion method for green timber would give adequate preservative retention in sa...
D Page, I Simpson, T Singh
Establishing the minimum effective penetration of wood preservatives in the refractory heartwood of E. nitens
2023 - IRG/WP 23-30780
Conventional pressure treatment of many Australian hardwoods results in little to no penetration of heartwood and a non-uniform envelope treatment of <5 mm surrounding a mostly untreated core. This is a major issue for many of the low durability plantation hardwood timbers that are grown in Tasmania, which contain high percentages of heartwood. Long term studies on softwoods such as spruce decking...
J R Vargas, J J Morrell, L Yermán, K C Wood
Performance of treated Malaysian semantang bamboo (Gigantochloa scortechinii) - field and laboratory durability evaluation
2023 - IRG/WP 23-30788
Field performance of sematan bamboo, Gigantochloa scortechinii was evaluated under the Malaysian tropical climate, along with laboratory evaluation to white-rot fungi and mold. Starch was removed from the bamboo by submerging the bamboo in the river for 6-8 weeks, kiln-dried and cut to 300 mm (L) round bamboo and 25 mm (W) x 50 mm (L) stripe for the field and laboratory test respectively. Bamboo w...
S Lipeh, T Khadiran, Z Jalaludin, M K Anwar U
Above Ground Proximity Decay Field Trial of Modified ACQ-A, Wolman® CA-B and Wolman® CA-C in Taiwan
2023 - IRG/WP 23-30793
An above ground proximity decay field trial was established at Chiayi county, Taiwan in July 2016. The purpose of this study was to generate local field performance data for Taiwan for Slash Pine treated with Wolman® CA-B, Wolman® CA-C and a modified ACQ-A product at AWPA UC3B actives retention. After 6 years of field trial, the efficacy of the wood preservative in preventing decay fungi and ter...
J-Y Gan
Estimation of single shear strength performance of screw joints with decayed wood
2023 - IRG/WP 23-40968
In order to use existing wooden structures for a long term, it is necessary to evaluate appropriately the damage degree of bio-deterioration of the structural performance including the members and joint systems. As one for them, it is necessary to estimate more accurate the single shear strength performance of screw joints with decay. Therefore, we proposed the model considering the yield strength...
R Inoue, K Tanaka, T Mori
Through-boring to improve the performance of low durability Eucalyptus species for utility poles: 10-year field test results of pole stubs exposed in Southeast Queensland
2023 - IRG/WP 23-40972
An impending shortage of naturally durable hardwood electricity pole timbers in Australia has encouraged investigation of alternatives containing less durable, untreatable heartwood. Through-boring or drilling holes perpendicular to the long axis before treatment, has been used successfully on refractory softwood poles in North America and might have application in Australia. The use of through-bo...
J Norton, L P Francis, J J Morrell