Your search resulted in 242 documents. Displaying 25 entries per page.
Conversion by insects – alternative method for wood waste up-cycling
2018 - IRG/WP 18-50337
Building industry is a major consumer of materials and waste generator in Europe. The bio-based building materials are considered as interesting alternative in modern building sector due to their low environmental impact. However, in order to increase confidence for bio-based materials application, they should present satisfying performance during service life allowing at the same time their casca...
A Sandak, J Sandak, M Kutnik, I Paulmier, C Brunet, M Petrillo, P Grossi
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Improvement of analytical methods of wood preservatives and its validation with collaborative testing
2019 - IRG/WP 19-20655
This discussion paper presents on-going collaborative test of analytical methods of wood preservatives according to the standardization process of Japan Agricultural Standard (JAS) by the Ministry of Agriculture, Forestry and Fisheries (MAFF). Food and Agricultural Materials Inspection Center (FAMIC) in close cooperated organization with the MAFF, has wide range of tasks about inspections and anal...
T Miyauchi, K Yamamoto, N Shota, Y Akabori, M Ikeda, J Eisawa, K Kambara, T Osawa, C Igarashi, Y Baba, W Ohmura, M Shimizu, M Samejima
Suggestive remarks for designing of experimental samples and trial devices to treat wood by pre-vacuumed immersion method
2019 - IRG/WP 19-40862
This study was conducted to test the impregnability of wood material according to the pre-vacuumed immersion process and to reveal the usability of cylindrical (plug) samples in impregnation experiments in addition to the cuboid or cubic samples. In this context, cuboids were prepared 30 mm in length, 20 mm in width and 20 mm in thickness, whereas plugs were prepared radially and longitudinally wi...
I Usta
Profiling fungal degradation of Scots pine sapwood by short wave infrared hyperspectral image analysis
2020 - IRG/WP 20-20667
Hyperspectral image analysis of Scots pine sapwood wood affected by decay fungi has been carried out as part of a Ph.D. thesis within the project Remote Inspection of Wooden Utility Poles (RIWUP).
In a lab experiment, Petri-dishes with Scots pine sapwood samples on malt agar medium were infected with two types of decay fungi, a brown rot and a white rot. The wood samples were scanned with a HySpe...
A Jochemsen, G Alfredsen, I Burud
Lab-scale termite damage synthesis using least squares generative adversarial networks
2020 - IRG/WP 20-20674
This manuscript investigated the feasibility of least squares generative adversarial networks (LSGAN) to generate synthetic images of lab-scale termite damage based on AWPA E1 standard, to push machine-learning forward into wood science field and to ameliorate the lack of a termite damage dataset. We leveraged LSGAN to learn the distribution of 203 uniquely termite damaged samples from previous ex...
D J V Lopes
Validating a short-term laboratory method to assess the resistance of timber to biodegradation by marine wood-borers
2021 - IRG/WP 21-10975
Novel approaches to protecting wood in coastal and marine environments are needed as the use of traditional broad-spectrum biocides are now restricted. Wood is widely utilised in marine environments where it can be rapidly degraded by wood-boring organisms, causing billions of dollars of damage per annum. Biocidal compounds such as CCA and creosote have been popular treatments for timber products ...
L S Martin, J R Shipway, G P Malyon, S M Cragg
Preliminary investigation for preservation method of CLT using non-pressure treatment
2021 - IRG/WP 21-40919
Cross-laminated Timber (CLT) is increasingly being used in residential and non-residential construction around the world, and some of these areas are at high risk of biodeterioration. Addition to moisture management of construction, preservative treatment of CLT may be needed to prevent decay and termite attack in the area. Pressure treatment being most reliable, is not feasible due to the large d...
T Miyauchi, Y Ohashi, J Miyazaki, R Takanashi, H Shibui, S Isaji, T Shigeyama, Y Sugai, A Yamamoto, T Hramiishi, T Mori, H Matsunaga
Evaluation of decay and energy properties from thermally modified biomasses during fungal deterioration by NIR-spectrometry
2021 - IRG/WP 21-40922
This study is focused on the prediction of fungal weight loss (WL) and high heating value (HHV) from raw and torrefied waste lignocellulosic feedstocks, according to their exposure duration to wood-destroying fungi, using near infrared spectroscopy (NIR) and chemometrics models.
Sugarcane bagasse, coffee husk, eucalyptus and pine shavings were torrefied at 290 °C in a screw reactor, during 5, 7...
B de Freitas Homem de Faria, P Santana Barbosa, J Valente Roque, A de Cassia Oliveira Carneiro, P Rousset, K Candelier, R F Teofilo
A novel method for assessing radial variation in termite resistance of timber
2023 - IRG/WP 23-11005
Australia has many timbers whose heartwood is highly resistant to fungal and termite attack; however, changing public policies have resulted in restricted access to many native forests where these species are found. Plantations of these same species are expected to replace these resources, but there are questions concerning whether timber from these trees will have the same resistance as the nati...
S Kleinschmidt, R McGavin
Japanese traditional wooden building construction project in Bangkok - Part 2 Verification of termite control method
2023 - IRG/WP 23-11022
We have confirmed the effectiveness in Thailand of chemicals and stainless steel mesh that have been proven effective in Japan.
Stake and container tests were conducted and the following results were obtained:
1. There is no damage on specimens covered with stainless steel mesh, CuAz-treated specimens both stake test and container test.
2. Natural pyrethrin-treated specimens without stainless ...
H Ishiyama, S Murakami
Mini-stakes – an alternative test method for EN 252?
2023 - IRG/WP 23-20691
Market approval of wood treatment products requires knowledge and prove of long-term durability. Efficiency of wood treatment with a specific product is evaluated based on variety of tests, including penetration evaluation, leaching studies as well as decay tests. EN 252 standard test is a core method for wood durability evaluation in a ground contact, both for commercial product approval and scie...
R Digaitis, P Larsson Brelid, N Terziev, M Klamer, A W Christof, J Stenaek, N Morsing
Field durability testing of wood above ground - Part 1: 15 years’ experience with the Bundle method
2023 - IRG/WP 23-20695
A ‘jack of all trades’ method for above-ground wood durability testing has been sought for decades, but until now no method has found its way into standardization. The method of choice shall be applicable for untreated and treated wood – ideally also for wood composites. It shall be reproducible, objective, fast, easy, and inexpensive. Finally, it shall provide high predictive power.
This s...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
Field durability testing of wood above ground - Part 2: The full guideline of the Bundle method
2023 - IRG/WP 23-20696
To determine the biological durability of wood above ground, numerous approaches for test methods have been pursued and tried out in the field in the past. So far, no method has managed to find its way into a European standard. During the last 15 years, experience with the Bundle method has been gained. As described in Part 1 of this paper, the method is recommended as a suitable tool for determin...
C Brischke, G Alfredsen, L Emmerich, M Humar, L Meyer-Veltrup
A simple method for assessing the effects of lyctid beetle attack on longitudinal compressive strength of spotted gum sapwood
2023 - IRG/WP 23-20700
Lyctid beetle attack is commonplace in a significant proportion of spotted gum utility poles that are air seasoned prior to chromated copper arsenate (CCA) treatment. While this damage is allowed, there are no reports quantifying the effects of the beetle galleries on pole properties. Full scale testing would require substantial quantities of poles in order to obtain a range of degrees of damage....
M Powell, J J Morrell
Geopolymer as a fixation method for tannin-based wood preservatives
2023 - IRG/WP 23-30774
This study aims to test if a second step impregnation with a geopolymer solution can fix Colatan GT10, a commercial extract rich in tannins, to wood, reducing their leaching and improving their performance as wood preservatives. Scots pine sapwood specimens of 40×10×5 mm3 were impregnated with Colatan GT10 tannin mix, geopolymer, and as combined treatment Colatan GT10 with subsequent geopolymer ...
Y M López-Gómez, A Barbero-López, A Haapala
Field test method for wood in above ground situation - The full CEN/TC 38 guideline for the Sandwich method. Part 1 - Determining the relative protective effectiveness of a wood preservative
2024 - IRG/WP 24-41013
The attached draft CEN Technical Specification (i.e. pre-EN standard) has been drafted in order to become an alternative to the Lap-Joint test method (EN 12037:23) for testing of wood in above ground situation and the draft CEN/TS Part 1 is specifically intended for determining the relative protective effectiveness of a wood preservative. The new draft CEN/TS is based on a test method developed by...
M Westin, R Ringman, A Christof, F Friese