Your search resulted in 866 documents. Displaying 25 entries per page.
Selection of heat flux value for wood fire retardants testing using MLC
2018 - IRG/WP 18-40846
One of more crucial elements of investigating treated wood combustion properties with the use of a cone calorimeter is a proper selection of heat flux (HF). The HF level is directly reflected in time to ignition and a thermal degradation degree. The ignition of raw wood or of wood ineffectively protected against fire occurs at a low HF level, i.e. 10-20 kW/m2. By contrast, the ignition of wood whi...
B Mazela, W Perdoch, W Grześkowiak, A Batista
Conversion by insects – alternative method for wood waste up-cycling
2018 - IRG/WP 18-50337
Building industry is a major consumer of materials and waste generator in Europe. The bio-based building materials are considered as interesting alternative in modern building sector due to their low environmental impact. However, in order to increase confidence for bio-based materials application, they should present satisfying performance during service life allowing at the same time their casca...
A Sandak, J Sandak, M Kutnik, I Paulmier, C Brunet, M Petrillo, P Grossi
Green Coloration of Wood in the Forest and Laboratory by Chlorociboria spp. – Applications for Furniture
2019 - IRG/WP 19-10947
Discoloration of wood caused by living saprophytic fungi is commonly found on lumber. These fungi do not destroy the integrity of wood, but the discolorations they cause are often considered undesirable. In Tunbrigde Wells (Great Britain), seldomly found green colored wood, usually considered commercially irrelevant, was valued for use in restoration of wood inlay artwork.
The aim of this researc...
S Krause, W Unger, P Heydeck
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Exploring the use of X-ray micro CT as a tool for the monitoring of moisture production and mass loss during lab-based fungal degradation testing
2019 - IRG/WP 19-20654
Bio-based building materials, such as wood and wood-engineered products, are susceptible to degradation by decay fungi. In-depth knowledge on the intricate material-fungus relationship as well as performance data for many bio-based building materials are still lacking, and especially knowledge on how a material’s structure and moisture properties affect the degradation process is missing. Althou...
L De Ligne, J Van den Bulcke, A De Muynck, J M Baetens, B De Baets, L Van Hoorebeke, J Van Acker
Performance of field cut preservatives above-ground and in ground contact exposures
2019 - IRG/WP 19-30742
Field cut preservatives are needed to protect cut ends and drill holes that expose the untreated interior of preserved wood. A series of field cut preservatives were assessed in ground contact and above-ground exposures. After 10 years in ground contact exposure, all of the untreated controls had failed or exhibited very advanced decay. In contrast, the copper naphthenate (2% Cu in mineral spirits...
R Stirling, D Wong
Suggestive remarks for designing of experimental samples and trial devices to treat wood by pre-vacuumed immersion method
2019 - IRG/WP 19-40862
This study was conducted to test the impregnability of wood material according to the pre-vacuumed immersion process and to reveal the usability of cylindrical (plug) samples in impregnation experiments in addition to the cuboid or cubic samples. In this context, cuboids were prepared 30 mm in length, 20 mm in width and 20 mm in thickness, whereas plugs were prepared radially and longitudinally wi...
I Usta
Durability testing of mass timber building elements: a call for a collaborative trial
2019 - IRG/WP 19-40875
Mass timber buildings have captured the imagination of architects and engineers seeking more environmentally friendly building materials. The mass timber movement has tremendous potential to markedly increase timber use in mid-rise to high rise buildings. With great promise, however, comes great risk. Most mass timber structures that have been built or are being planned use no protective treatm...
J J Morrell
Performance of naturally durable decks after 15 years of field exposure
2020 - IRG/WP 20-10963
A decking test of Canadian species considered to be naturally durable was inspected after 15 years of exposure at test sites in Ontario and British Columbia. Based on the materials used in this experiment, Douglas-fir and yellow cypress had the greatest decay resistance, followed by eastern white cedar and western redcedar, and then by western larch and tamarack. All materials tested were more dur...
R Stirling, D Wong
Resistance against marine borers: About the revision of EN 275 and the attempt for a new laboratory standard for Limnoria
2020 - IRG/WP 20-20669
Wood protection technology in the marine environment has changed over the last decades and will continue to do so. New active ingredients, newer formulations, and novel wood-based materials including physically- and chemically-modified wood, together with increasing concerns over environmental impacts of wood preservatives, urgently demand a major revision of EN 275 “Wood preservatives – Deter...
S Palanti, S Cragg, R Plarre
Application of diverse hyperspectral imaging systems for evaluation of heritage objects
2020 - IRG/WP 20-10971
Advanced imaging techniques are able to non-invasively characterize, monitor and evaluate the impact of conservation treatments on cultural heritage (CH) objects. In this specific field, hyperspectral imaging (HI) allows non-destructive characterization of materials by identifying and characterizing colouring agents, binders and protective coatings as constituents of an object’s original constru...
J Sandak, A Sandak, L Legan, K Retko, M Kavčič, J Kosel, F Poohphajai, R Herrera Diaz, V Ponnuchamy, N Sajinčič, Č Tavzes, P Ropret
The role of specimen format in wood durability testing
2020 - IRG/WP 20-20672
The experimental basis for testing the biological durability of wood are often incubation experiments with wood-destroying basidiomycetes. Numerous parameters can affect the mass loss by fungal decay (MLF) in laboratory durability tests and therefore being decisive for the resulting durability classification. Among others, the dimension of the wood specimen and the time of incubation impact on fun...
C Brischke, L K Grünwald, S Bollmus
Development of procedures for sampling, testing, and classification to determine the biological durability of wood and wood products
2020 - IRG/WP 20-20676
This paper informs about a research project, which deals with several shortcomings and a lack of clarity within EN 350:2016. The project started in January 2020, will run for 3 years, and is operated by the Institute of Wood Technology Dresden (IHD) and the University of Goettingen (UGOE).
Determination and classification of durability of wood and wood products against wood-destroying organisms ...
W Scheiding, K Jacobs, S Bollmus, C Brischke
Durability of acetylated Radiata pine: Laboratory tests and performance in practice
2020 - IRG/WP 20-40899
Wood acetylation is an established process to enhance biological durability and dimensional stability of lower valuable wood species without the use of biocides. Acetylated Radiata pine (ACCOYA® wood) has been on the market for more than 10 years now, starting in 2007.
Numerous lab tests have confirmed the high durability of acetylated Radiata pine. Here, additional data with four Radiata pine ...
K Jacobs, W Scheiding, B Weiß
Preliminary investigation for preservation method of CLT using non-pressure treatment
2021 - IRG/WP 21-40919
Cross-laminated Timber (CLT) is increasingly being used in residential and non-residential construction around the world, and some of these areas are at high risk of biodeterioration. Addition to moisture management of construction, preservative treatment of CLT may be needed to prevent decay and termite attack in the area. Pressure treatment being most reliable, is not feasible due to the large d...
T Miyauchi, Y Ohashi, J Miyazaki, R Takanashi, H Shibui, S Isaji, T Shigeyama, Y Sugai, A Yamamoto, T Hramiishi, T Mori, H Matsunaga
Post-layup protection of mass timber elements in above ground protected exposures: 2-year results
2022 - IRG/WP 22-30766
Mass timber has seen increased use as a building material for low and mid-rise construction in recent decades. The durability of mass timber elements has not been fully examined and the effects of wood destroying organisms on this these materials merits attention. The effectiveness of currently labeled soil termiticides and passively applied biocides at post-construction or as remedial agents need...
M E Mankowski, T G Shelton, G T Kirker, J J Morrell
Above-Ground Termite Resistance of Naturally Durable Species in Ontario and Mississippi
2022 - IRG/WP 22-30767
A collaborative above-ground protected termite field test was initiated by FPInnovations and the USDA Forest Service at sites in Ontario and Mississippi. The aims of the experiment were to compare the rate of attack in protected, above-ground exposures by the subterranean termite species, Reticulitermes flavipes, between northern (Ontario) and southern (Mississippi) test sites and to generate perf...
R Stirling, M Mankowski
Copper Naphthenate – A Data and Capability Update
2022 - IRG/WP 22-30771
The efficacy of copper naphthenate against wood decay fungi and wood destroying organisms has been well documented from international field tests as well as decades of commercial service. The use of copper naphthenate has been dramatically expanded due to its proven performance, non-restricted use, minimal environmental impact, and superior end of life options. Extensive demand and interest has al...
J-W Kim, J D Lloyd
A Comparison of Cross-Laminated Timber (CLT) Floor Panels using Finite Element Analysis and Experimental Fire Testing
2022 - IRG/WP 22-40955
Cross-laminated timber (CLT) is a relatively new timber product and has gained popularity in North America and Europe as a construction material. As a sustainable engineered timber product, CLT offers many advantages over solid wood, concrete, or steel construction. However, the use of timber in medium to high rise buildings is often avoided mainly due to its combustible nature. In this paper, a n...
M Yasir, A Macilwraith, K Ruane
A novel method for assessing radial variation in termite resistance of timber
2023 - IRG/WP 23-11005
Australia has many timbers whose heartwood is highly resistant to fungal and termite attack; however, changing public policies have resulted in restricted access to many native forests where these species are found. Plantations of these same species are expected to replace these resources, but there are questions concerning whether timber from these trees will have the same resistance as the nati...
S Kleinschmidt, R McGavin
Natural durability of 9 tropical species suitable for round wood timber building: fungi and termites laboratory screening tests
2023 - IRG/WP 23-11013
In numerous tropical forest species, wood properties are poorly described and wood is under-valorized. Especially very few is known about small diameter trees although they may be used, directly as round wood, in construction timber building. A selection of abundant species was done and characterization tests were performed to assess their usability as building material. The aim of this work was t...
M Leroy, K Candelier, J Damay, J Bossu, R Lehnebach, M-F Thevenon, J Beauchene, B Clair
Japanese traditional wooden building construction project in Bangkok - Part 2 Verification of termite control method
2023 - IRG/WP 23-11022
We have confirmed the effectiveness in Thailand of chemicals and stainless steel mesh that have been proven effective in Japan.
Stake and container tests were conducted and the following results were obtained:
1. There is no damage on specimens covered with stainless steel mesh, CuAz-treated specimens both stake test and container test.
2. Natural pyrethrin-treated specimens without stainless ...
H Ishiyama, S Murakami
Efficacy of a wide-spectrum plant bio-based anti-termite product - Laboratory trials
2023 - IRG/WP 23-11024
Compared to the number of timbers available, the list of wood species resistant to termites is rather limited and largely composed of tropical timbers. In addition, due to climate change and environmental degradation, together with global trade, a significant global expansion of termites is predicted along with the economic losses due to their activities. Therefore, there is a demand to find produ...
M-F Thévenon, F Chopinet, J Vuillemin, A Robert, S Lafay, D Messaoudi
Mini-stakes – an alternative test method for EN 252?
2023 - IRG/WP 23-20691
Market approval of wood treatment products requires knowledge and prove of long-term durability. Efficiency of wood treatment with a specific product is evaluated based on variety of tests, including penetration evaluation, leaching studies as well as decay tests. EN 252 standard test is a core method for wood durability evaluation in a ground contact, both for commercial product approval and scie...
R Digaitis, P Larsson Brelid, N Terziev, M Klamer, A W Christof, J Stenaek, N Morsing
Glued laminated poles - Progress report after 43 years of testing
2023 - IRG/WP 23-20692
In 1979, a number of glued laminated poles treated with CCA and creosote were placed in a greenhouse in Uppsala, in the Simlångsdalen test field in south-western Sweden and in a power lane in Vuollerim in northern Sweden, in order to study their resistance against biological degradation. The test poles were treated in a two-step process. All laminations of Scots pine (Pinus sylvestris) were first...
J Jermer, M Westin, N Terziev