Your search resulted in 230 documents. Displaying 25 entries per page.
Susceptibility of wood substrates to Aurebasidium pullulans at different temperatures
2016 - IRG/WP 16-10863
There is an increasing awareness of how the aesthetical performance of wood exposed outdoors changes over time and especially in the first few years after installation. Mould and blue stain fungi are biological agents that contribute to the weather grey colour on a wooden façade, and the blue stain fungi Aureobasidium pullulans is commonly identified as colonizer on coated and uncoated wood expos...
L Ross Gobakken, G Alfredsen
Durability of a willow/plastic composite mat
2016 - IRG/WP 16-20592
Developing uses for wood wastes could enhance utilization of low value renewable materials while creating opportunities for rural development. Small diameter willow stems have little use in China, but they could be combined with high density polyethylene to create wood plastic composite mats for decorative applications. These mats could be used in exterior, above ground exposures, but would still ...
Li Yan, Haiyan Duan, Beizhan Quan, J Cappellazzi, J J Morrell
Distribution and penetration of the tung oil in wood studied by high-resolution magnetic resonance imaging
2016 - IRG/WP 16-20593
Water repellents as environment-friendly treatments are gaining their popularity as non-biocidal solutions for wood protection. One of the most important water repellents for wood besides waxes and organosilicon compounds are drying oils. Tung oil is one of the best performing oil. However, tung oil, similarly as other oils, does not penetrate deeply into wood, due to its high viscosity. In order...
M Žlahtič, U Mikac, I Serša, M Merela, M Humar
Effects of fungal exposure on air and liquid permeability of nanosilver- and nanozincoxide-impregnated Paulownia wood
2016 - IRG/WP 16-30680
Effects of aqueous dispersion of silver and zinc-oxide nano-particles on air and liquid permeability of Paulownia wood exposed to T. versicolor were studied in the present research project. Specimens were also heat-treated at 100 and 150°C and compared with the control specimens. Permeability values were measured when the moisture content of the specimens was 12%. Results showed significant incre...
H R Taghiyari, A Kalantari, M Ghorbani Kookandeh, F Bavaneghi, M Akhtari
A Comparison on Penetration of Silica Sol in Scots pine and Southern pine wood
2016 - IRG/WP 16-40722
Penetration is one of the most important issues to be considered in wood impregnation with various kinds of chemicals in liquid form. Scots pine (Pinus sylvestris) and Southern pine (Pinus spp.) are two frequently used wood species for treatment, such as preservative treatment. With the development of treating systems, some micro- or nano-sized aqueous modifiers are emerging in the market, which p...
Mingyang Sun, Jinzhen Cao
Modifying wood with paraffin wax emulsion impregnation and thermal modification: hydrophobization effect and mechanism of the combined treatment
2016 - IRG/WP 16-40726
The aim of this study was to enhance the water repellency of wood by a combined treatment of paraffin wax emulsion (PWE) impregnation and thermal modification. Two different treating procedures were used to modify the southern pine (pinus spp.). One is first PWE impregnation and then thermal modification, another is first thermal modification and then PWE impregnation. The treated samples were imm...
Wang Wang, Jinzhen Cao, Cong Chen
Fabrication and characterization of MicroPCMs filled wood-plastic composites: Effects of polyethylene glycol on melamine–formaldehyde shell material
2016 - IRG/WP 16-40728
Microencapsulated phase change materials (MicroPCMs) containing dodecanol were fabricated using melamine-formaldehyde (MF) or polyethylene glycol 200 modified melamine-formaldehyde (PMF) resin as the shell materials by in situ polymerization. Wood flour/high-density polyethylene (WF/HDPE) composites with MF shell MicroPCMs (MF-MicroPCMs) or PMF shell MicroPCMs (PMF-MicroPCMs) were prepared, respec...
Xi Guo, Jinzhen Cao
Superhydrophobic treatment of Norway spruce wood for improvement of its resistance against brown rot and moulds
2016 - IRG/WP 16-40734
Water repellence of wood can be increased and its some other properties influenced by introduction of hydrophobic chemicals into and on cell walls without affecting the wood’s bulk density due to lumen filling. Herein, a simple dipping method to insert octadecyltrichlorosilane (OTS) into cell walls and to deposit the self-assembled hydrophobic monolayers (SAMs) of OTS is reported. It was found o...
A Kumar, P Ryparová, P Hajek, B Kričej, M Pavlič, A S Škapin, M Šernek, J Tywoniak, J Žigon, M Petrič
The influence of log soaking temperature and thermal modification on the properties of birch veneers
2016 - IRG/WP 16-40749
In veneer manufacture the logs are routinely soaked in heated water baths in order to soften the wood prior to peeling. The temperature of the water may vary greatly between batches; however, the influence of log soaking temperature on veneer properties has had little research attention. Uncontrolled moisture is known to cause problems in wood-based materials, while thermal modification offers a m...
S Källbom, K Laine, M S Moghaddam, A Rohumaa, K Segerholm, M Wålinder
Development of Wood Modification – High melting point wax and hot oil treatments
2016 - IRG/WP 16-40768
This study covers an introduction to the projects where new facilities were created for developing wood modification. In this new research environment it is possible to treat wood with versatile equipment. First modifications with this equipment are going to be done in high temperature and pressure using high melting point waxes and hot oils.
Earlier studies, tests and commercial products show...
H Turunen, L Linkosalmi, J Peura, O Paajanen
Effects of climatic factors and material properties on mould growth on untreated wooden claddings
2017 - IRG/WP 17-10884
Mould growth is an important contributor to colour change of untreated wood exposed outdoors. Predicting the development of mould growth is therefore important to ensure successful use of untreated wood as a façade material. More knowledge about the factors affecting mould growth on outdoor exposed wood is required to give better predictions. In this study, climatic factors and material propertie...
S Karlsen Lie, G I Vestøl, O Høibø, L Ross Gobakken
Effect of Particle Size on Wax Distribution in Paraffin Wax Emulsion Impregnated Wood
2017 - IRG/WP 17-40779
Paraffin wax emulsion impregnation has been a common eco-friendly approach for improving water repellency of wood. In this study, southern pine (Pinus spp.) and Scots pine (Pinus sylvesteris L.) samples were impregnated with paraffin wax emulsions of different solid contents and particle sizes, and then the time domain nuclear magnetic resonance (TD-NMR) was used to elucidate the influence of part...
Wang Wang, Jinzhen Cao, Yiheng Huang
Moisture behaviour and biological durability of high performance flax fibre reinforced composites
2017 - IRG/WP 17-40803
For natural fibre composites in structural and load bearing applications long reinforcing fibres are required. Therefore, much research is performed on flax fibre reinforced composites to optimize them for high performance use. In most cases such research focuses on the mechanical properties, yet the assessment of moisture behaviour, dimensional stability and biological durability is an important ...
N Defoirdt, J Van den Bulcke, F Bensadoun, J Ivens, I Verpoest, J Van Acker
Influence of hygro-thermal treatment temperature and duration on dimensional stabilisation of wood modified with poly(butylene succinate)
2017 - IRG/WP 17-40813
To improve wood properties, especially dimensional stability, a treatment based on poly(butylene succinate) oligomers (OBS) was experimented. After impregnation in wood, a further hygro-thermal treatment (HTT) was carried out in a pressurized reactor at 100% relative humidity (RH) at differing temperatures for differing durations. The aim of HTT is to induce partial swelling of wood cell walls so ...
C Grosse, M Noël, L Rautkari, P Gérardin
Fipronil Concentrations in Soil after Vertical Termiticide Applications Using the “Termidor®H•P High Precision Injection System”
2017 - IRG/WP 17-20630
Termidor®H•P II High Precision Termiticide concentrations in sandy-loam and sandy-clay-loam building foundation soil were measured 1.0-hour after high-pressure vertical liquid injections into the soil using the Termidor®H•P High Precision Injection System. Cylindrical, vertical 30.5-cm-deep soil cores were extracted and separated into four 7.6-cm-long sequential partitions, and fipronil res...
B M Kard
Impact of temperature and relative humidity on spatio-temporal fungal growth dynamics of Basidiomycetes
2018 - IRG/WP 18-10905
Basidiomycetes can cause considerable damage to wood and other bio-based building materials. Knowing at which environmental conditions these decay fungi generally thrive, and how the environmental conditions affect fungal growth characteristics, is therefore of particular interest. In this paper, we use image analysis to assess the impact of the environmental conditions on the growth dynamics of C...
L De Ligne, G Vidal-Diez de Ulzurrun, J Van den Bulcke, J M Baetens, B De Baets, J Van Acker
Wood Hydrophobic Modification by Mixed Wax Emulsions
2018 - IRG/WP 18-40839
An environmental-friendly, economical and facile method to construct hydrophobic system for improving wood repellency was applied in this study. Using paraffin wax and carnauba mixed wax O/W emulsions can simultaneously fabricate continuous wax films and rough structures in wood internal and external surface under appropriate heat treatment. In the study, single and mixed wax emulsions of 4% solid...
C Chen, W Wang
A Synergistically Stabilized Oil-in-Water Paraffin Pickering Emulsion Used in Wood Treatment
2018 - IRG/WP 18-40840
Pickering emulsions (emulsions stabilized by solid particles) are attractive as they have strong similarities with traditional surfactant-stabilized emulsions. In this study, an oil-in-water (O/W) paraffin Pickering emulsion system with satisfying stability and small droplet size distribution was developed by hydrophilic silica particles and traditional surfactants as mixed emulsifiers. The drople...
J Jiang, J Cao
Monitoring of the building made of CLT in Ljubljana
2019 - IRG/WP 19-40860
Wood is one of the most important construction materials and its use in building applications has further expanded in recent decades, predominately due to development of the modern composites, like cross-laminated timber. In order to enable even more extensive and reliable use of wood in outdoor applications, factors affecting wood’s service life need to be understood. It is well known that fung...
M Humar, D Krzisnik, B Lesar, N Thaler, B Dujic
Promoting Commercially Available Epoxy Resins for Non-biocidal Wood Preservation
2019 - IRG/WP 19-40877
Commercially available epoxy and polyamine resins were evaluated with the aim of developing new non-biocidal wood preservation treatments. A simple method allowing the impregnation of wood by vacuum double impregnation followed by a curing process was developed for two reference species, beech Fagus sylvatica and Scots pine Pinus sylvestris. The tested products were evaluated for their ability to ...
P Poveda, M Mubarok, S Dumarcay, M Montibus, I Le Bayon, M Kutnik, P Gerardin, F Simon
Wood veneer with high flexible decorated with nanoparticles for highly efficient water treatment
2019 - IRG/WP 19-50347
Natural wood is mainly comprised of numerous long, partially aligned channels (lumens) as well as nanochannels. Wood with these quick and effective passages is suitable for a membrane/separation material. However, a suitable thickness range of wood along its growth direction is essential to effectively separate small molecular, and the wood membrane is too thick to clean easily. In this paper, woo...
S Chang, D Xu, G Liu, J Hu, X Li, Y Liu
Moisture and temperature conditions in an old, highly moisture-loaded timber building in the Røros municipality, Norway
2020 - IRG/WP 20-10966
A 150 years old log building near Røros, Norway, has been in active use as a cowshed since its erection. The animals are kept inside the cowshed all winter and this causes a situation of a high moisture load on the wooden floor, wooden walls and ceiling. Logging of temperature and humidity over one year shows that there are favourable levels of moisture in the wood and air for development of moul...
M Sand Austigard, J Mattsson
Development of Wooden Fireproof Structures for Mid- and High-rise Buildings in Japan
2021 - IRG/WP 21-30757
When constructing a mid-to-high-rise building more than 4 stories in general in Japan, it is necessary to have a fireproof structure stipulated by the Building Standard Law. The performance required as a fireproof structure in Japan is generally stricter than in other countries, and it is required to be structurally sound after a fire even without fire extinguishing activities. In order to satisfy...
D Kamikawa, M Harada, H Matsunaga, R Takase, N Hattori, Keisuke Ando, M Miyabayashi
Premature adhesion failure of exterior wood coatings – The influence of substrate temperature at coating application and moisture accumulation during storage
2022 - IRG/WP 22-40937
The present study aimed at extending the knowledge about premature coating failures of industrially finished wood cladding. Two potential factors were studied: the influence of substrate temperature at coating application and moisture accumulation during storage on the adhesion of waterborne coating systems. In the first experiment, 4 batches of wood specimens were submitted to 4 different tempera...
U Hundhausen
Joints design considerations in indoor high humidity conditions
2022 - IRG/WP 22-40950
In recent years, a number of cases of degradation by wood destroying fungi have been detected in covered timber structures such as pools, wineries, bathrooms, etc. – in fact, any building where indoor air may reach high humidity values during certain periods of time.
The origin of this kind of decay was not related to water leaks, but to the condensation of the water vapor over the steel connec...
A Lozano, D Lorenzo, M Alonso, F Álvarez, J E Martínez