Your search resulted in 475 documents. Displaying 25 entries per page.
Influence of pressure phase impregnation time on the uptake and distribution of wood preservatives in Scots pine material of diverse treatability
2016 - IRG/WP 16-40752
In spite of the general opinion that Scots pine sapwood is easy to impregnate considerable variations in treatability are reported. In order to study impregnation results of diverse Scots pine sapwood treated with increasing process times, Scots pine sapwood from two different predefined treatability groups was impregnated. A copper solution was used as impregnation agent in ten different vacuum p...
K Zimmer, B Kerfriden
Dynamics of biofilm formation on wood impregnated with vegetable oils
2016 - IRG/WP 16-40769
Biofilms can be used as a living protective coating for wood, showing advantages compared to traditional wood-coatings regarding sustainability and self-repair. Biofilms can be formed on oil impregnated wood. Such an oil-biofilm system has the potential of protecting the wood against UV and bio degradation, creating a homogeneously black surface with self-healing properties. Results of biofilm for...
K Filippovych, H Huinink, L van der Ven, O C G Adan
Bio-deterioration of Southern Pine Stakes at Geographically Different Testing Sites
2017 - IRG/WP 17-20609
Southern pine (SP) sapwood is commonly used in preparing the standardized stakes for performance testing as referenced in the American Wood Protection Association (AWPA) Book of Standards. For example, the standardized above ground test methods E16/E18 and the standardized ground contact test method E7 all use sapwood of SP as the preferred wood species for preservative performance test. In this...
Jun Zhang, J Horton
Three-Dimensional Digital Image Correlation of Strains in Profiled Wood Decking Exposed to Wetting & Drying
2017 - IRG/WP 17-20611
We use three dimensional digital image correlation to measure the strains that develop at the surface of profiled radiata pine (Pinus radiata D. Don) deck boards subjected to a wetting and drying cycle. We hypothesise that surface profiling will change the pattern of strain distribution at the surface of deck boards by concentrating stresses at the base of profile grooves. Five groups of three deck board samples were produced from five different pieces of machine stress-graded radiata pine wood. Two wavy profiles, ribble or ripple, were tested. Flat unprofiled boards acted a control. Each board was fixed to a rigid frame and subjected to a wetting and drying cycle. Full field surface strain data was collected using 3D digital image correlation. Strains varied across the surface of both flat and profiled boards. Profiling changed surface strain patterns; strain maxima and minima developed in the profile ridges and grooves during wetting, respectively, but this pattern of strains reversed during drying. Such a pronounced reversal of strains was not observed when flat boards were exposed to wetting and drying, although there was a shift towards negative strains when flat boards were dried. We conclude that profiling changes surface strain distribution in deck boards exposed to wetting and drying, and causes high strains to develop in the grooves of profiled boards. These findings help explain why checks in profiled deck boards are mainly confined to profile grooves where they are difficult to see, and the success of profiling at reducing the negative effects of checking on the appearance of wood decking.
J Mallet, S Kalyanasundaram, P D Evansa
Decay Resistance of Scotch pine Wood Impregnated with Agaricus campestris Bio-Protective Extract
2017 - IRG/WP 17-30714
In this study it was investigated that the possibilities of the use of fungal extract as wood protection solution against wood destroying fungus. For that purpose; the decay resistance of Scotch pine wood samples, impregnated with Agaricus campestris (field mushroom) fungal extract, was examined against the brown rot fungi “Coniophora puteana”. Impregnation procedure was applied in accordance ...
S Yildiz, Ü C Yildiz, A Yilmaz
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Dimensional Stability of Melamine Formaldehyde-Treated Southern Pine
2017 - IRG/WP 17-40774
The objective of this preliminary study was to evaluate the influence of different levels of melamine formaldehyde (MF) and curing cycle on the dimensional properties of southern pine. Thirty samples for each combination of treatment and curing regimen plus untreated controls and controls subjected to the same curing regimen were tested. Shrinkage/swelling coefficients showed that up to 60% ASE c...
H M Barnes, L S Sites, T S F A França, M G Sanders, F J N França
Is the SPM 15 effective? Survival of Pine Wood Nematode under thermal treatments
2017 - IRG/WP 17-40775
The pine wood nematode Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle (PWN) is the causal agent of “Pine wilt disease” affecting coniferous forests, and since its detection in 1999 in Portugal, has obligated the European Union to take action to prevent its spread (Decision 2006/133/CE). The main measure applied is the International Standard for Phytosanitary Measures ISPM No. 15 (ISPM ...
L Robertson, M Conde, J C Cabrero, F Llinares, M T Troya
The potential and the challenges of acetylated wood in timber bridges - experiences from an ongoing project
2017 - IRG/WP 17-40792
Acetylated wood is known to be a durable and dimensional stable alternative for high performance materials, and has high potential for exterior timber structures. Research has shown that acetylated wood can be effectively bonded by various adhesive types. However, one of the most common used adhesives for timber constructions, Melamine Urea Formaldehyde (MUF), shows a high degree of delamination o...
A Treu, R Bredesen, F Bongers
Plasma-assisted bleaching of blue-stain from lodgepole pine wood
2017 - IRG/WP 17-40799
We hypothesize that plasma will etch wood and fungal hyphae in blue-stained lodgepole pine, and increase the ability of hypochlorite bleach to remove discolouration from blue-stained wood. Blue-stained lodgepole pine wood was exposed to a glow-discharge plasma derived from water, and the surface wettability, permeability and colour of the treated wood was measured. Plasma-treated wood was dipped i...
A Jamali, P D Evans
A summary of history and use of timber bridges in New Zealand
2017 - IRG/WP 17-40801
Wooden bridges have been an important part of road and rail networks in New Zealand. While wooden structures have largely been replaced by concrete and steel on major arteries they still have a place where lightweight, easily assembled structures are needed. These timber bridges may also be a cheaper alternative to other materials in roads which carry relatively low traffic loads. In the last ten ...
D Page, T Singh
Penetration behaviour of different hydrophobic carrier substances for oily wood preservatives in Beech and Scots pine sapwood
2017 - IRG/WP 17-40804
The use of creosote as a wood preservative has a long history. Current areas of application are railway sleepers, transmission poles, timber bridges and marine applications. If the approval for creosote will not be prolonged, alternative wood preservatives will be needed. As the penetration behaviour after pressure impregnation of different alternative oily products in this fields of application i...
M Starck, A Gellerich, H Militz
Decay resistance of beams made from thermally modified Scots pine and Norway spruce after 6 years’ exposure in ground contact
2017 - IRG/WP 17-40806
In the present study the resistance of beams treated by ThermoWood® process was studied in ground contact and the results given are based on a “modified” EN 252 test. After six years’ exposure clear differences were found between untreated Scots pine and Norway spruce beams and treated ones. In all cases thermal modification improved the performance. Thermally modified pine heartwood showed...
S Metsä-Kortelainen, H Viitanen
Multivariate modeling of mould growth in relation to extractives in dried Scots pine sapwood
2017 - IRG/WP 17-20629
Influence of extractives on mould growth on Scots pine sapwood dried in air or in kiln was studied. Boards were sprayed with water mixtures of spores of the fungal species Penicillium sp., Aspergillus sp., Mucor sp., Paecilomyces sp., Trichoderma sp., treated at a temperature of 22ºC at 90% RH, classified into a percentage of covered area. Acetone and water extracts were isolated and analyzed for...
O Karlsson, O Myronycheva, M Sehlstedt-Persson, M Öhman, D Sandberg
Impact of sapwood portions on the durability of adjacent heartwood of Pinus sylvestris, Pseudotsuga menziesii and Quercus robur. Part 1: Laboratory studies
2018 - IRG/WP 18-10922
Sapwood is generally considered as non-durable and assigned to durability class DC 5 according to European standards independent from the wood species. It is commonly agreed that sapwood decays faster than adjacent heartwood, but it is controversially discussed whether sapwood serves as feeder material and thus accelerates onset and progress of decay in more durable heartwood or decays independent...
C Brischke, P Homann, A Gellerich
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
An examination of the potential for the use of the Maillard reaction to modify wood
2018 - IRG/WP 18-40829
Finding efficient ways to decrease wood decay caused by fungi and increasing its dimensional stability is an important issue in the timber construction. A possible way to avoid wood decay by fungi is by reducing the water content of wood, since water is a primary condition for fungal growth. Bulking of the wood cell wall by chemical reagents occupies the space where water normally occurs. At the s...
K Peeters, E Larnøy, A Kutnar, Č Tavzes, C A S Hill
Thermally modified timber treated with methacrylate
2018 - IRG/WP 18-40849
Thermally modified timber (TMT) from Scots pine sapwood similar to Thermo-D quality was impregnated with methacrylate resin by the hot-and-cold method and subsequently cured at elevated temperatures. The results showed that methacrylate resin could be used to reduce colouring of painted TMT wood during accelerated weathering probably by hindering the migration of extractives. The resin itself did ...
O Karlsson, O Myronycheva, DJones, D Elustondo, D Sandberg
Performance of untreated timbers in above ground decking tests: Preliminary results from an international collaborative trial
2019 - IRG/WP 19-10940
The ability to accurately predict wood decay risks under varying environmental conditions has long been of interest to timber users. Accurate predictions are difficult owing to the myriad of variables associated with the decay process including wood species, wood inhabiting organisms, timber building element design and environmental conditions. Despite these difficulties, decay predictions have be...
L P Francis, J Norton, E Melcher, A H H Wong, J Kok Lai, M Klamer, M J Konkler, J J. Morrell
Accumulation of copper in parenchyma cells in southern pine wood treated with micronized and amine-copper preservatives
2019 - IRG/WP 19-20657
Our previous research used X-ray micro-computed tomography to examine the micro-distribution of copper in southern pine wood treated with a micronized wood preservative (MCA) and an amine-copper preservative (ACQ). We found that copper in wood treated with MCA was mainly concentrated in fusiform rays (rays containing resin canals), and in vertical (axial) resin canals. A similar, although not iden...
D Feng, M L Turner, A Limaye, M A Knackstedt, P D Evans
Efficacy of microwave treatments against Pine Wood Nematode
2019 - IRG/WP 19-20658
The pine wood nematode Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle (PWN) is the causal agent of “Pine wilt disease” affecting coniferous forests, and since its detection in 1999 in Portugal, has obliged the European Union to take action to prevent its spread (Decision 2006/133/CE). One of the main measures applied is the International Standard for Phytosanitary Measures ISPM No. 15 ...
L Robertson, M T Troya, F Llinares, J C Cabrero
The development of a suitable fire retardant for Radiata pine and other species
2019 - IRG/WP 19-30744
The use of fire retardant chemicals, with the overarching aim of creating a safer environment is not a new one, however it is generally under-developed and is often afflicted with an image of environmental and health issues and misperceived high costs. There is an ever-increasing need and desire for effective fire retardancy in timbers to inhibit or suppress the combustion process. This is paramou...
B R Derham, M R Fortune
Chemical Analysis of Southern Pine Pole Stubs Sixty Months Following Treatment with a Methylisothiocyanate-Based Solid Fumigant Stick
2019 - IRG/WP 19-30740
Methylisothiocyanate-based fumigants have been commercially used in the United States for over 35 years to control internal decay in utility poles and other wooden structures with little technological advancement. The most recently commercialized methylisothiocyanate-based fumigant is chemically known as dazomet. Dazomet is a free-flowing powder or granule that decomposes in the presence of mois...
D J Herdman, T Pope, R R Browning
The anti-weathering mechanism of extractives in thermally modified Scots pine
2019 - IRG/WP 19-40880
Results from the electron spin-resonance spectroscopy (ESR) analysis indicated that thermally modification of wood can inhibit the generation of phenoxyl radicals during UV irradiation and consequently lead to the increase of the color stability of wood. In order to clarify the evolution and role of extractives in thermally modified wood during the process of weathering, the compositions of aceton...
H Shen, J Cao
Terrestrial laser scanning (TLS) – a potential tool for improved utilisation of the natural durability of Scots pine for solid wood products
2019 - IRG/WP 19-50358
The natural durability of sapwood of most species is generally low, while heartwood can be more resistant to biodeterioration. For the sawmill industry various lumber products require certain diameters and lengths of the logs in addition to requirements for wood properties. When utilising the heartwood, it is therefore important to acquire information already in the forest about which trees that c...
P-O Flaete