Your search resulted in 138 documents. Displaying 25 entries per page.
Rapid detection of the Alaska yellow cedar, Callitropsis nootkatensis (Cupressaceae) extractives using Fourier transform infrared (FT-IR) spectroscopy
2017 - IRG/WP 17-20612
Global changes in wood harvesting towards plantation species grown on much shorter rotations has the potential to markedly alter wood quality perceptions. Nowhere is this more risky than with naturally durable species where there is compelling evidence that faster grown woods tend to be less durable. The ability to non-destructively assess durability may allow growers to identify materials that re...
S Lipeh, J J Morrell
Thermal stability of a wood protective biofinish and the influence of flame retardants on Aureobasidium cells
2017 - IRG/WP 17-30716
In general there is an increasing need for sustainable resources, including sustainable building materials. Wood is one of these sustainable resources and is more used as an outdoor building material. Since unprotected wood will usually be degraded during outdoor exposure, many different protection systems are available on the market. Protection systems containing biocides however might create obs...
S Rensink, E A M Klein Rot, M F Sailer
Effects of heat treatment on sound absorption coefficients in nanosilver-impregnated and normal solid woods
2017 - IRG/WP 17-40770
Effects of impregnation with silver nano-suspension as well as heat-treatment on sound absorption coefficients (AC) were studied in tangential direction of five different solid woods based on their importance. AC was measured at two frequencies of 250 and 500 Hz. A 400 ppm nanosuspension was used for the impregnation; silver nanoparticles had a size range of 30-80 nm. Based on the obtained results...
A Esmailpour, J Norton, H R Taghiyari, H Zolfaghari, S Asadi
Water absorption characteristics of CLT
2017 - IRG/WP 17-40817
CLT is initialism of Cross Laminated Timber. CLT is generally large-sized panel which can use many woods efficiently, so it is attracted attention recently in Japan. Therefore, many studies about CLT are carried out. However, there are few studies about durability of CLT. Avoiding water infiltration is important for durability of wooden building. CLT has many edge-glued points which has risk of w...
D Yokoi, H Ishiyama, Y Hirano
Natural durability, ethanol-toluene extractives and phenol content prediction of eight wood species from Madagascar using NIRS multispecific models
2018 - IRG/WP 18-10926
Madagascar has nearly 4000 species of trees and shrubs, but wood properties of only 200 species have been studied. Some properties, such as the natural durability or chemical composition are of importance for adequate and optimal use of these timber species. Since durability tests take long time and chemical analyzes can be very expensive, alternative methods such as near infrared spectroscopy (NI...
A R Razafimahatratra, H Rakotovololonalimanana, M-F Thévenon, C Belloncle, G Chaix, T Ramananantoandro
The Study of the Preparation of Overlaid MDF with the Flame Retardant Impregnated Paper
2018 - IRG/WP 18-40848
The preparation of overlaid medium density fiberboard (MDF) was studied. The flame retardant impregnated papers (FRIP) were overlaid on the surface of the MDF for the fire protection. The results showed that: 1) The production of the FRIP was based on the technology of melamine-impregnated paper, which required the viscosity of the impregnated resin lower than 20s. However, with the addition of th...
W Qu, M Wu, Y-Z Wu
The use of bicine and tricine as possible Maillard reagents in a combined thermal/chemical modification of beech
2019 - IRG/WP 19-40852
The effects of thermal modification have been well established, particularly in terms of reductions in mechanical performance. In recent years, there has been an increase in studies related to the Maillard reaction. More commonly associated with food chemistry, it involves the reaction of amines and reducing sugars during cooking procedures. This paper has attempted to combine the use of amines an...
D Jones, C-M Popescu, D Krzisnik, M Hocevar, M Humar, M-C Popescu
Development of Wooden Fireproof Structures for Mid- and High-rise Buildings in Japan
2021 - IRG/WP 21-30757
When constructing a mid-to-high-rise building more than 4 stories in general in Japan, it is necessary to have a fireproof structure stipulated by the Building Standard Law. The performance required as a fireproof structure in Japan is generally stricter than in other countries, and it is required to be structurally sound after a fire even without fire extinguishing activities. In order to satisfy...
D Kamikawa, M Harada, H Matsunaga, R Takase, N Hattori, Keisuke Ando, M Miyabayashi
Evaluation of decay and energy properties from thermally modified biomasses during fungal deterioration by NIR-spectrometry
2021 - IRG/WP 21-40922
This study is focused on the prediction of fungal weight loss (WL) and high heating value (HHV) from raw and torrefied waste lignocellulosic feedstocks, according to their exposure duration to wood-destroying fungi, using near infrared spectroscopy (NIR) and chemometrics models.
Sugarcane bagasse, coffee husk, eucalyptus and pine shavings were torrefied at 290 °C in a screw reactor, during 5, 7...
B de Freitas Homem de Faria, P Santana Barbosa, J Valente Roque, A de Cassia Oliveira Carneiro, P Rousset, K Candelier, R F Teofilo
Carbon nanotubes and multifunctional silane additive as fillers in PF resin and their effect on the composite flammability
2023 - IRG/WP 23-30783
Adhesive bonds are the most readily modifiable and, at the same time, give the greatest scope for modification of components of lignocellulosic composites. A study of a manufactured lignocellulosic composite based on a phenol-formaldehyde resin and pine veneer with additives modifying the properties of the resin was made. The multifunctional commercial silicon oxide Protectosil 851 and multi-walle...
W L Grzeskowiak, B Mazela, T Prowadzisz
Failure characteristics of thermally modified poplar wood subjected to mechanical tests
2023 - IRG/WP 23-40983
Poplar (Populus spp.) are among the fastest growing timber species and have been widely planted for use in plywood, composites, pallets, furniture components and paper production. However, the low density of the wood limits many structural applications and the wood has little resistance to biodegradation. Thermal modification represents one approach to improving durability by changing the moistur...
E Bari, M Ghorbanian Far, N Moradi, J J Morrell, G Daniel, B Mohebby, R Hosseinpourpia, M Humar
Short-term absorption of water and coatings on thermally modified blue-stained spruce wood
2023 - IRG/WP 23-40984
The importance of wood has been increasing in the last decades. Among conifers, predominantly spruce (Picea abies) wood is often used in building constructions in Europe. Namely for construction and facades of buildings, decking and fences. Due to the increased public concerns about biocides, alternative techniques for protection, such as thermal modification and protection by construction, are ga...
R Hasanagic, M Bahmani, M Humar, L Fathi, L Cai
Evaluation of the water exclusion ability and inherent bioactivity of heartwood against decay in Japanese and European wood species via above-ground exposure and water absorption tests
2024 - IRG/WP 24-40998
The natural durability of wood has been thought to mainly depend on bioactive extractives and the water exclusion ability. To clarify the contribution of each factor to wood durability, above-ground exposure tests were conducted on Japanese and European wood species. A double-layer test was carried out using heartwood specimens of four wood species, i.e., Japanese cedar, Japanese cypress, Scots pi...
T Osawa, R Noda, K Yamamoto