Your search resulted in 146 documents. Displaying 25 entries per page.
NIR spectroscopy for rapid determination of permethrin or bifenthrin retention in P. radiata sapwood
2013 - IRG/WP 13-20507
Near infrared spectroscopy of permethrin or bifenthrin treated radiata pine (P. radiata D.Don) has been used to develop calibration models to later predict the active retention in unknown samples. Calibrations were developed for both a laboratory NIR and a portable NIR using laboratory-prepared calibration samples at a range of target retention levels. Correlations were established between the act...
R Meder, N Ebdon
Determination of the natural durability of solid wood against wood-destroying fungi - a European round-robin test
2013 - IRG/WP 13-20511
In Europe the durability of wood against wood-destroying basidiomycetes is tested according to CEN/TS 15083-1 (2005). Hitherto existing experience with this standard is quite heterogeneous and results from previous round-robin tests have stayed unreported or have been reported incompletely. In particular the need for natural pre-weathering of the test specimens to allow potential detoxification of...
C Brischke, C R Welzbacher, A Gellerich, S Bollmus, M Humar, K Plaschkies, W Scheiding, G Alfredsen, J Van Acker, I De Windt
Statistical analysis of durability tests - Part 2: Principles of time-to-failure and application on field test data
2013 - IRG/WP 13-20512
Service life prediction is an important topic in wood research, especially with regard to the Construction Products Regulation (CPR). Both laboratory tests as well as in-service performance testing is therefore essential, in combination with proper monitoring and analysis tools. A crucial concept is variability and the incorporation of variability in tests and analysis. In this paper we focus on t...
J Van den Bulcke, I De Windt, C Brischke, C R Welzbacher, A O Rapp, J Van Acker
Developing Analytical Methods for Determination of Quaternary Ammonium Compounds (DDAC) using HPLC and HPLC-MS (Application to treating solution and preservatives treated wood)
2013 - IRG/WP 13-20516
Korea preservative treating industry has mainly used alkaline copper quaternary (ACQ) expected over 80% of market share in Korea. ACQ employs dodecyl dimethyl ammonium chloride (DDAC) and benzyl dimethyl dodecyl ammonium chloride (DBAC) for active ingredient along with copper. The strongly increasing domestic applications for wood preservatives require developing accurate and reproducible analytic...
Sung-Mo Kang, Kwon-Min Kim, Won-Mo Koo, Myeong-Won Cho
Extraction and analysis of DNA from green and seasoned timber as basic methods for determination of wood species and origin
2013 - IRG/WP 13-20523
Against the background of the European timber trade regulation EUTR, commenced to law by March 2013, the determination of wood species and tracing of its origin is getting a great importance. A promising approach for establishing fast and reliable tracking systems for wood products is DNA analysis. A critical point is the extraction of analysable DNA from the wood and its lignified cell walls. Thu...
K Jacobs, H Mende, W Scheiding
Assessment of Scots pine sapwood susceptibility to moulds by determination of fungi growth and ergosterol content in infested wood
2014 - IRG/WP 14-20540
The susceptibility of wood to filamentous fungi (mould) attack is determine mainly by laboratory methods with descriptive grading of fungal growth on the surface of the wood specimens. It is a lot of different grading scale of fungi growth, but determination of the size of fungi growth is many times not easy, not clear and often difficult. Although the filamentous fungi are not included to microor...
A Fojutowski, A Koziróg, A Kropacz
Nano-Zycosil in MDF. Part I: Gas and Liquid Permeability
2014 - IRG/WP 14-40652
Effects were studied of zycosil nanoparticles, with size range from 20 to 80 nm, on liquid and gas permeability of medium density fiberboard. Nanozycosil was used at four consumption levels of 0, 50, 100, and 150 g/kg dry wood fibers. Density of all treatments was kept constant at 0.67 g/cm3. The obtained results indicated that the addition of zycosil to the mat resulted in a significant increase...
H Reza Taghiyari, A Karimi, P M D Tahir, O Schmidt, E Bari, P Nouri , A Jahangiri
Effect of silver nanoparticles on the rate of heat transfer to the core of the medium-density fiberboard mat
2014 - IRG/WP 14-40653
Effect of silver nanoparticles on the rate of heat transferred to the core section of medium-density fiberboard (MDF) mat was studied here. A 400 ppm aqueous nanosilver suspension was used at three consumption levels of 100, 150, and 200 mL/kg based on the weight of dry wood fibers; the results were then compared with the control MDF panels. The size range of silver nanoparticles was 30-80 nm. Res...
H Reza Taghiyari, O Schmidt, E Bari, P M Tahir, A Karimi, P Nouri, A Jahangiri
Effect of natural variability of European Oak wood on heat treatment process and potential implication on wood durability
2015 - IRG/WP 15-40693
Environmental pressures appeared in France and in most European countries during the last decade has led to the development of more environmentally acceptable preservation methods. In this context, wood heat treatment has been one of the most investigated alternative method during the last years. Treated at temperatures ranging between 180 and 220°C, wood components undergo more or less important...
J Hamada, A Pétrissans, F Mothe, M Pétrissans, P Gérardin
Durability of a willow/plastic composite mat
2016 - IRG/WP 16-20592
Developing uses for wood wastes could enhance utilization of low value renewable materials while creating opportunities for rural development. Small diameter willow stems have little use in China, but they could be combined with high density polyethylene to create wood plastic composite mats for decorative applications. These mats could be used in exterior, above ground exposures, but would still ...
Li Yan, Haiyan Duan, Beizhan Quan, J Cappellazzi, J J Morrell
Effect of Nano-Silane on Permeability in MDF as a Result of Susceptibility to Moulds and Fungi
2016 - IRG/WP 16-40716
Effects were studied of vapor chamber on specific gas permeability of nanosilane-treated medium-density fiberboards (MDF). Size range of nanoparticles was 20 – 80 nm. Nano-silane (NS) was used at four consumption levels of 0, 50, 100, and 150 g/kg dry wood fibers. Density of all treatments was kept constant at 0.67 g/cm3. Specimens were kept for 18 weeks in vaporized chamber; their specific gas ...
H R Taghiyari, J Norton, A Moradiyan, M Sadegh Taher Tolou Del, H Siahposht, B Moradi-Malek, M Noferesti
How intraspecific radial variability of the European Oak’s may influence mild pyrolysis process and durability of the material
2016 - IRG/WP 16-40725
Last decades wood is promoted as building material. Unprotected wood exposed to outdoor conditions undergoes a variety of degradation induced essentially by fungi attacks. Heat treatment of wood by mild pyrolysis (180°C T 240°C under inert atmosphere) is a preservation process with a weak environmental impact, and therefore, is viewed as an interesting alternative to the chemical impregnation me...
J Hamada, A Pétrissans, F Mothe, M Pétrissans, P Gérardin
Moisture content as a quality control parameter in thermally modified timber production
2017 - IRG/WP 17-20622
Quality assurance (QA) or factory production control (FPC) is necessary to ensure a proper production process. The requirements of QA/FPC can result from EN and national standards, quality assurance systems, or producer-specific rules.
TMT producers must ensure that the process was correct, and to ensure traceability of products. In addition to the electronic records, the material should be che...
W Scheiding, H Turkulin, S Stein
On the natural durability of RED MERANTI for window frames as a function of gross density wood
2018 - IRG/WP 18-10927
MERANTI is a wood species belonging to the family Dipterocarpaceae, in the genus SHOREA (Shorea spp.). The genus has approximately 196 species with four subgenera. The subgenus RUBROSHOREA is commonly named RED MERANTI (RM) and is found on the Malayan Island of Sarawak, Indonesia, with approximately 65 varieties (Symington 1943). According to Brazier (1956), the distribution of gross densities wi...
K Hasse, W Unger, T L Woods
The anatomical determination of wood samples found in the “Fürstengräber” from Lübsow (Poland)
2018 - IRG/WP 18-10930
The paper presents the results of anatomical research identifying three wooden fragments from the “Princes Graves” (“Fürstengräber”) in Lübsow, Poland. The research demonstrates that the wooden fragments are typical of wood harvested from European forests.
The physicals conclusions are important for the research of Jan Schuster, from the University of Lodz, Institute of Archeology, Pol...
J Schuster, W Unger, T L Woods
Natural durability of four Tunisian Eucalyptus wood species and their respective compositions in extractives
2019 - IRG/WP 19-10942
In the 50’s, Tunisia government introduced more than 11 Eucalyptus wood species. Eucalyptus species were planted in Tunisia in different arboreta throughout the country for close observation and adaptation to climate and soil. These fast-growing wood species were mainly used as fire wood, for the production of mine wood and to fight against the erosion. These tree species were adapted themselve...
S Ben Ayed, M T Elaieb, S Dumarçay, B De Freitas Homen De Faria, M-F Thévenon, P Gerardin, K Candelier
Using X-ray micro-CT to evaluate density loss in anobiid infested wood
2019 - IRG/WP 19-10956
Considering the relevance of wood borers in construction, the present study had as main objective the evaluation of the impact of anobiid damage on timber elements by establishing an empirical correlation between lost material percentage (LM%, consumed by beetles) and apparent density (original – OTD and residual – RTD). Since the beetles’ attack produces a diffuse damage with a set of tunne...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Validation by micro-computed tomography of an assessment method to measure the residual strength of anobiids infested timber
2019 - IRG/WP 19-20650
In this article a quantitative correlation study of pine timber structural elements, which have been subject to attack by anobiids, is presented. The main objective of the study was to establish a valid empirical correlation between the lost material percentage (consumed by beetles) and original/residual apparent density. Since the beetles’ attack produces a diffuse damage with a set of tunnels ...
J L Parracha, M F Pereira, A Maurício, P Faria, L Nunes
Elucidation of reactive sites of wood modified with acetic anhydride: Insights from density functional theory calculations
2020 - IRG/WP 20-40892
Density functional theory (DFT) was employed to investigate the interaction of cellulose and lignin with acetic anhydride for explaining the wood modification process. Atoms in molecules (AIM) and reduced density gradient (RDG) along with non-covalent interaction (NCI) plots were used to analyse the intermolecular bonding characteristics. Cellulose was modelled with a cellobiose unit (dimer of glu...
V Ponnuchamy, A Sandak, J Sandak, R Herrera Diaz
The impact of pre-drying on treatment level variations of esterified solid wood analysed by X-ray densitometry
2023 - IRG/WP 23-40977
Wood modification requires homogenous treatment levels within the wood matrix to prevent insufficiently treated areas being subject to biodeterioration. Esterification of wood by citric acid and sorbitol can show differences in density caused by uneven chemical distribution during the curing phase and can be detected by x-ray densitometry. This study used density profiling to investigate the influ...
A Treu, S O Amiandamhem, E Larnoy
Effectivity of zinc borate in medium density fiberboard (MDF) for ground proximity testing
2024 - IRG/WP 24-20723
Medium-density fiberboard (MDF) is one of the most used and versatile wood composites. Most of its use has been focused on interior applications. Adhesives such as p-MDI (polymeric methyl diphenyl diisocyanate) provide MDF with a better performance against moisture, but resistance against decay is also required for outdoor use. A mix of wood fibers, p-MDI, and 0.75%-1.5% of ZB was made to produce ...
S M Vega Gutierrez, T Olivadoti