Your search resulted in 391 documents. Displaying 25 entries per page.
Development of a new method for wood hydrophobizing and fixation of copper compounds by chemical hardening of vegetable based modified oils
2016 - IRG/WP 16-40754
Wood products with ground and direct water contact, but without sufficient biological durability, have to be protected against biological degradation by fungi and other microorganisms. Due to European legislation (Biocidal Products Regulation 528/2012), the selection of possible chemical agents, which are still allowed to be used, is diminishing rapidly. The use of previously widely applied, very ...
C Swaboda, M Fischer, K Jacobs
Development of Wood Modification – High melting point wax and hot oil treatments
2016 - IRG/WP 16-40768
This study covers an introduction to the projects where new facilities were created for developing wood modification. In this new research environment it is possible to treat wood with versatile equipment. First modifications with this equipment are going to be done in high temperature and pressure using high melting point waxes and hot oils.
Earlier studies, tests and commercial products show...
H Turunen, L Linkosalmi, J Peura, O Paajanen
Wood Protection and Environmental Performance of Products - Impacts COST Action FP1407 Aims to Bring
2016 - IRG/WP 16-50323
Though many aspects of wood modification (chemical, thermal, impregnation) treatments are known, the fundamental influence of the process on product performance, the environment, and end of life scenarios remain unknown. To contribute to the low-carbon economy and sustainable development, it is essential to integrate interactive assessment of process parameters, developed product properties, and e...
A Kutnar
Chemical compositions and anti-termite activities of essential oils from Gabonese Canarium schweinfurthii Engl, Dacryodes buettneri Engl and Aucoumea klaineana Pierre wood resins.
2017 - IRG/WP 17-10895
Essential oil extract from resins of Canarium schweinfurthii, Dacryodes buettneri and Aucoumea klaineana woods from Cap Esterias and Oyem areas, Gabon, were prepared by Clevenger - steam distillation. The chemical compositions of these respective essential oils were analyzed by a Gas Chromatography coupled with Mass Spectrometry (GC-MS). Although monoterpenes were the main constituents of the thre...
Chemical compositions and anti-termite activities of essential oils from Gabonese Canarium schweinfurthii Engl, Dacryodes buettneri Engl and Aucoumea klaineana Pierre wood resins.
Weathering protection of European hardwoods through double modification
2017 - IRG/WP 17-30715
Beech and poplar were thermally modified, treated with melamine resin and both treatments were combined. The weathering performance (cracks and general appearance) of modified beech and poplar was assessed in natural weathering and correlated to material properties such as work in bending (WB) and Brinell hardness. In addition, the equilibrium moisture content after exposure of 12 months and subse...
G Behr, A Gellerich, S Bollmus, H Militz
Effects of heat treatment on sound absorption coefficients in nanosilver-impregnated and normal solid woods
2017 - IRG/WP 17-40770
Effects of impregnation with silver nano-suspension as well as heat-treatment on sound absorption coefficients (AC) were studied in tangential direction of five different solid woods based on their importance. AC was measured at two frequencies of 250 and 500 Hz. A 400 ppm nanosuspension was used for the impregnation; silver nanoparticles had a size range of 30-80 nm. Based on the obtained results...
A Esmailpour, J Norton, H R Taghiyari, H Zolfaghari, S Asadi
Commercialisation of DMDHEU Modified Wood in Australasia
2017 - IRG/WP 17-40772
While there is an increasing volume of data for the impregnation and curing of timber using dimethylol dihydroxyethyleneurea (DMDHEU) on species such as Scots Pine, Beech, Slash Pine and Spotted gum, there is limited information available on the impact of the modification process on the performance of Pinus radiata (referred to hence forth as Radiata pine). The variability within material and spec...
B R Derham, T Singh, H Militz
Effect of Particle Size on Wax Distribution in Paraffin Wax Emulsion Impregnated Wood
2017 - IRG/WP 17-40779
Paraffin wax emulsion impregnation has been a common eco-friendly approach for improving water repellency of wood. In this study, southern pine (Pinus spp.) and Scots pine (Pinus sylvesteris L.) samples were impregnated with paraffin wax emulsions of different solid contents and particle sizes, and then the time domain nuclear magnetic resonance (TD-NMR) was used to elucidate the influence of part...
Wang Wang, Jinzhen Cao, Yiheng Huang
The use of new, aqueous chemical wood modifications to improve the durability of wood-plastic composites
2017 - IRG/WP 17-40787
The wood flour used in wood-plastic composites (WPCs) can biologically deteriorate and thus the overall mechanical performance of WPCs decrease when exposed to moisture and fungal decay. Protecting the wood flour by chemical modification can improve the durability of the wood in a nontoxic way so it is not harmful to the environment. WPCs were made with modified wood flour and then evaluated for m...
R E Ibach, C M Clemons, G C Chen
The potential and the challenges of acetylated wood in timber bridges - experiences from an ongoing project
2017 - IRG/WP 17-40792
Acetylated wood is known to be a durable and dimensional stable alternative for high performance materials, and has high potential for exterior timber structures. Research has shown that acetylated wood can be effectively bonded by various adhesive types. However, one of the most common used adhesives for timber constructions, Melamine Urea Formaldehyde (MUF), shows a high degree of delamination o...
A Treu, R Bredesen, F Bongers
Studying Weathering Performance of Coatings on Thermally Modified Wood
2017 - IRG/WP 17-40805
Thermal modification and degree of improved properties depends on wood species and treatment parameters. Southern pine and spruce are the two common wood species for decking, fences and siding in North America. This study was the first to evaluate coating performance when applied on oil-heat-treated southern pine and spruce wood samples. Water uptake, colour and gloss changes of samples were analy...
M Nejad, M Dadbin, P Cooper
Impact of heat treatment on physico-mechanical properties of torrefied Antholceistha djalonensis wood
2017 - IRG/WP 17-40811
Thermal modification at relatively high temperatures is an effective method to improve the dimensional stability and mechanical properties of wood. This study was carried out to investigate the impact of heat treatment on the physic-mechanical properties of torrefied Anthocleistha djalonensis wood. Thirty nine defect-free specimens of dimensions 20 mm × 20 mm × 60 were prepared for the determina...
E A Iyiola, B Olufemi, J A Fuwape, J M Owoyemi
A Green and Novel Technology for Recovering Copper and Wood from Treated Wood Waste – Part II: Optimization, copper metal recovery, and process design
2017 - IRG/WP 17-50326
The US consumes 70 million pounds of copper and produces 580 million cubic feet treated wood annually. The EPA disallows burning and reusing treated wood waste due to health/environmental concerns. Vast quantities of copper and wood are landfilled. Two safe and low cost extraction systems, citric acid and ammonium citrate, were identified in Part I of this study. In Part II of the study, effects o...
S Chen, R Patel
Corrosion verification experiment of the screw driven into CLT
2017 - IRG/WP 17-40816
Japan has abundant forest resources, but we depend on import for 70 percent of the consumed timber. Japan has the vision which promotes the timber self-sufficiency rate 30% to 50% by 2020. Therefore CLT attracts attention as a new timber material. Japan has a climate with high temperature and humidity, and wooden buildings are often treated with chemicals as a measure against biological deteriorat...
N Wada, H Ishiyama, S Yamamoto
Biocontrol of wood decay insects and nematodes as an alternative to traditional chemical treatments
2018 - IRG/WP 18-10914
The protection of wood has been defined until relatively recently, as the application of a chemical to increase its durability. On the other hand, society is becoming more and more demanding in terms of the use of products which have the minimum ecological impact. This has led many countries to reduce the list of biocidal products that can be used (European Biocides Regulation), therefore it is ne...
L Robertson, J F Galván, F Llinares, R Viñambres, M T de Troya
Natural resistance of Bambusa vulgaris to termite and powder-post beetle attack in laboratory and graveyard tests
2018 - IRG/WP 18-10925
Deterioration is the major setback to the utilisation of bamboo products. To enhance bamboo utilization, an understanding of the level of resistance to degradation is important. In this study, level at which Bambusa vulgaris will naturally resistant attack by subterranean termites and powder-post beetles were evaluated. B. vulgaris aged 2, 3 and 4 years were subjected to attack by subterranean ter...
N A Sadiku, S O Bada
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Chemical composition and termiticidal activity of Khaya ivorensis stem bark extracts on woods
2018 - IRG/WP 18-30723
The genus Khaya is extractives rich, but the extractives in the stem bark are among the most abundant, accessible and utilised materials in Nigeria. These extractives are of considerable interest for wood protection because of their pesticidal properties. In this study, the chemical constituents of Khaya ivorensis stem bark (KISB) and their termiticidal activity were investigated on Triplochiton s...
G A Adedeji, O Y Ogunsanwo, F S Eguankun, T O Elufioye
Multiscale modification on water resistance and dimensional stability of Populus cathayana by alkali lignin combined with heat treatment
2018 - IRG/WP 18-40826
The aim of this study was to enhance the water resistance and dimensional stability of fast growing wood by alkali lignin combined with heat treatment. Poplar (Populus cathayana) samples were first impregnated with alkali lignin solution and then subjected to heat treatment at 140, 160, and 180°C respectively for 2h. Properties of leachability, moisture adsorption and water absorption, contact an...
H Zhou, J Li, E Ma
Thermodynamic properties of furfurylated wood during moisture adsorption process
2018 - IRG/WP 18-40828
Furfurylation of wood seems a promising wood modification method considering the wide raw material source of furfuryl alcohol (FA) and overall performance of FA modified wood. However, the modification mechanism of furfurylation is still not clear and needs further investigation. In this study, poplar (Populus cathayana Rehd.) samples with the size of 1(R) mm × Ф4 mm, were impregnated with ...
J Wang, J Cao, T Yang, E Ma, W Wang
An examination of the potential for the use of the Maillard reaction to modify wood
2018 - IRG/WP 18-40829
Finding efficient ways to decrease wood decay caused by fungi and increasing its dimensional stability is an important issue in the timber construction. A possible way to avoid wood decay by fungi is by reducing the water content of wood, since water is a primary condition for fungal growth. Bulking of the wood cell wall by chemical reagents occupies the space where water normally occurs. At the s...
K Peeters, E Larnøy, A Kutnar, Č Tavzes, C A S Hill
Wood Hydrophobic Modification by Mixed Wax Emulsions
2018 - IRG/WP 18-40839
An environmental-friendly, economical and facile method to construct hydrophobic system for improving wood repellency was applied in this study. Using paraffin wax and carnauba mixed wax O/W emulsions can simultaneously fabricate continuous wax films and rough structures in wood internal and external surface under appropriate heat treatment. In the study, single and mixed wax emulsions of 4% solid...
C Chen, W Wang
Improvement of short rotation teak wood properties through thermal modification
2018 - IRG/WP 18-40842
Teak (Tectona grandis L.f) is one of the most popular tropical timber species. Nowadays, the source of long rotation teak is limited in the availability. Many wood processing industries use short rotation teak, which has lower quality especially in durability and dimensional stability. Heat treatment is an eco-friendly method improving dimensional stability and durability of wood. The objectives o...
L A Pratiwi, I W Darmawan, B George, A Merlin, C Gérardin, S Dumarçay, T Priadi, P Gérardin
Developments within COST Action FP1303 related to the modification of wood
2018 - IRG/WP 18-40847
COST Action FP 1303 (Performance of bio-based building materials) was established in 2013 with the main aim to improve the knowledge on the performance of bio-based materials used as building products and the assessment of factors influencing these, with the aim of increasing their service life. This Action has helped in understanding the interlinked relationships between durability, product aesth...
D Jones
Polyesterification of wood using sorbitol and citric acid under aqueous conditions
2018 - IRG/WP 18-40851
The aim of this research is to determine if the polyesterification of sorbitol and citric acid in wood has a future potential as a wood modification process. Pine wood was impregnated with an aqueous solution containing citric acid and sorbitol and was thereafter cured at 103, or 140°C for 18 hours. The dimensional stability and leaching resistance were studied for both modification temperatures....
E Larnøy, A Karaca, L R Gobakken, C A S Hill